My brother has 17 doors in his house that need mortise locks installed.
He wishes to cut the mortises with the doors hanging. I would like to
know if there is a cheap, simple way to bore for the mortises that is
better than hand-drilling. I have bored out many mortises with my drill
press, but never free-hand.
On Apr 10, 2:43=A0pm, Han <[email protected]> wrote:
> This afternoon's excitement upstairs of my son's:
> She locked herself out. =A0Neede help calling a locksmith. =A0Locksmith c=
ame
> really fast (~20 min) and drilled out the lock (didn't go to see the
> process). =A0Charged $340. =A0Girl was happy, then locked herself out aga=
in. =A0
> Putty knife did the job this time.
> Wipe your monitor.
LMAO!!
No kidding... after that first bill, I'll bet creative thinking was in
full gear!
Robert
This is pretty much the industry standard for <<mortise>> locks, and
has been for many decades. Nice piece of equipment!
http://www.amazon.com/Porter-Cable-513-Horsepower-Lock-Mortiser/dp/B0000224LA
If you are talking about plain drilled out locks with only the tongue
and strike mortised out, in the industry these aren't considered
"mortise" locks. Just plain door locks.
There are a dozen versions of this model, which will do the standard 2
3/8 backset with 15/16" or 1" tongue cylinder hole.
If he isn't good with a chisel, I think Amazon has an IRWIN model that
has a router guide that will attach to the door and you can router out
the small mortise on the tongue cylinder instead of chiseling it out.
For an installer, an chisel would no doubt be faster, but for someone
that doesn't use tools a lot, chiseling out those little mortises can
take a lot of time.
Robert
On Apr 10, 10:38=A0pm, "DanG" <[email protected]> wrote:
> Robert, I agree on the Porter Cable. =A0Mine is a 1950's version. =A0I
> wouldn't loan it out and I'm not aware of anyone who would rent
> one. =A0I also would not care to take on multiple mortise locks with
> speed bore and chisel.
If I had the PC version of that vintage, I wouldn't even let anyone
touch it, much less use it. I have only seen a small few over the
years, and the old ones are much better made and to tighter tolerances
than the newer ones.
And no one rents those things.
I don't have one myself, regardless of the age.
And in fact, I only install from scratch a box lock about every 18
months or so. It seems clients started spending more money on the
castings and finishes, and less on the mechanical workings of
locksets. Just doesn't seem to be much call for that type of
installation anymore.
Robert
On Apr 10, 11:18=A0am, scritch <[email protected]> wrote:
> I know, I know. =A0I would take the doors off, myself. =A0My brother does
> things his own way.
FWIW, I do this for a living. I never bore, mortise and fit unless
the door is hung.
I actually don't know anyone that does unless they are working at the
door plant.
Robert
On Apr 10, 12:48=A0pm, -MIKE- <[email protected]> wrote:
> Have you found it to be easier that way, or what?
A great deal easier, and more important, less hard on the door. If I
am re-locking or retrofitting, I go in after the finishing or painting
is done.
I will not go in, fit locks and install them, then take them off,
store them, then go reinstall them after finishing. So when you "lock
out" a house, you are tail end charlie.
1) You cannot take a chance on scuffing or scratching finishes from
handling doors when removing or reinstalling. No matter how careful
you are, you will slip somewhere and the door will need a refinish.
So you leave them on the hinges, then put the locks on in place
2) When you install a door, the installation of the frame and the door
reveals, final placement of the door in the jamb, etc., are more of a
feel you get rather than installing with a level or square. Twisted
jambs, uneven floors, etc., all make the tongue/strike relation very
relative. In a perfect world, the door is in a square frame that is
plumb and level. You can get close, but no cigar most of the time.
If you are in a tract home or production home, the "close" tolerance
rule applies. You move the strike, fill the screw hole with a sliver,
them mortise out to the new position. This is common with shop built
doors that are fitted door-to-jamb in a plant and bored and mortised
accordingly.
If you have the door hung on site and it looks great, reveals all
perfect, tight fit against the jambs, etc., you can mark the door for
lock/strike location, and since you aren't moving the door, when it
closes it will always return to the same exact place. This makes your
measured and carefully marked door and jamb line up every time.
If you mark the door and the jamb and remove the door from the jamb,
it may not hang back the same way. With today's crappy hardware, I
have seen many, many bent hinge pins that still work fine, but hold
the door a certain way. If I take a door off the hinges by pin
removal, I now label the pins. I learned this the hard way, and you
can't seem to spot "those" hinges until it is too late. So now, look
at the three hinged doors that are so popular. These hinges are
pretty flimsy since they now use three instead of just two. NOTE: The
third hinge BTW is to assist in keeping the masonite/particle board
doors from warping in the jamb, not to make it a better door. I have
removed doors for refinishing (oops... trim carpenter error!) that
were these 6 panel masonite doors, and found that after working on
them for a couple of hours they have warped on the saw horses.
I don't want to wrestle with rehanging a potentially warped door,
wagging around a door in a house to get it to my work area, or winding
up with doors have a less than *click* close when I am finished with
the hardware.
For a guy like me, it is easier to mark, drill and chisel once to get
a good fit. I mark, drill, then sit on a five gallon paint bucket and
do the rest of the fitting. Also, when drilling the tongue cylinder,
I find it much easier to gauge left and right by keeping the drill
parallel to the door by doing it this way.
Depending on the lock/latch/strike, I can go start to finish (marking
to final adjustment) in +/- 30 minutes.
In the end, the door isn't moved so the finish isn't in danger (no $$$
for finish repair, even if it someone else that knocks over the door
or drags their nail bags across it), and it always goes back to the
original spot after the hardware is prepped and installed.
Robert
Robert, I agree on the Porter Cable. Mine is a 1950's version. I
wouldn't loan it out and I'm not aware of anyone who would rent
one. I also would not care to take on multiple mortise locks with
speed bore and chisel.
--
______________________________
Keep the whole world singing . . . .
DanG (remove the sevens)
[email protected]
<[email protected]> wrote in message
news:233aa9bf-84a6-45ea-b069-6be01de0d7db@z14g2000yqa.googlegroups.com...
> This is pretty much the industry standard for <<mortise>> locks,
> and
> has been for many decades. Nice piece of equipment!
>
> http://www.amazon.com/Porter-Cable-513-Horsepower-Lock-Mortiser/dp/B0000224LA
>
> If you are talking about plain drilled out locks with only the
> tongue
> and strike mortised out, in the industry these aren't considered
> "mortise" locks. Just plain door locks.
>
> There are a dozen versions of this model, which will do the
> standard 2
> 3/8 backset with 15/16" or 1" tongue cylinder hole.
>
> If he isn't good with a chisel, I think Amazon has an IRWIN
> model that
> has a router guide that will attach to the door and you can
> router out
> the small mortise on the tongue cylinder instead of chiseling it
> out.
>
> For an installer, an chisel would no doubt be faster, but for
> someone
> that doesn't use tools a lot, chiseling out those little
> mortises can
> take a lot of time.
>
> Robert
I work for a major school district. The only kind of locks we use
on new or old are full mortise. When I went to work for them,
they had not ever seen the Porter Cable, so I brought mine in.
The project had over 60 doors. Once they saw how mine operated,
they purchased the current model. Not an everyday use, but
indispensable. I've never looked for one on Craiglist or Ebay.
--
______________________________
Keep the whole world singing . . . .
DanG (remove the sevens)
[email protected]
<[email protected]> wrote in message
news:[email protected]...
On Apr 10, 10:38 pm, "DanG" <[email protected]> wrote:
> Robert, I agree on the Porter Cable. Mine is a 1950's version. I
> wouldn't loan it out and I'm not aware of anyone who would rent
> one. I also would not care to take on multiple mortise locks
> with
> speed bore and chisel.
If I had the PC version of that vintage, I wouldn't even let
anyone
touch it, much less use it. I have only seen a small few over the
years, and the old ones are much better made and to tighter
tolerances
than the newer ones.
And no one rents those things.
I don't have one myself, regardless of the age.
And in fact, I only install from scratch a box lock about every 18
months or so. It seems clients started spending more money on the
castings and finishes, and less on the mechanical workings of
locksets. Just doesn't seem to be much call for that type of
installation anymore.
Robert
"Swingman" wrote:
> Bingo ... and ONLY until _you_ get finished will the bank release
> the remainder of the construction loan, something they will not do
> with a construction door still on.
My father's words still ring in my ears on the subject of bankers.
"If you can prove to the SOB's you don't need the money, the skies the
limit on how much they will loan you, but God forbid you need the
money, you're between a rock and a hard place."
(The cleaned up version<Grin>).
Lew
"[email protected]" <[email protected]> wrote in news:fd364295-
[email protected]:
> On Apr 10, 1:28 pm, "Lew Hodgett" <[email protected]> wrote:
>> "scritch" wrote:
>>
>> .
>>
>> > I would like to know if there is a cheap, simple way to bore for
>> > the mortises that is better than hand-drilling.
>>
>> This is a case where "cheap" & "simple" are mutually exclusive terms.
>>
>> Lew
>
> No kidding. That's a real understatement. I knew a lock guy that I
> used to run into that sub contracted installation of full mortise
> locks. He only installed top line Baldwins, etc. NO bored locks,
> ever.
> Full box mortises were all he did.
>
> He did one to two a day in the upscale neighborhoods for several of
> the high end remodelers. I was stunned when he told me what the PC
> mortising machine cost and I thought he was kidding me. Nope.
>
> Then he told me what he charged for the installation of full mortise
> lock and matching deadbolt. $375 - $425.
>
> He had a three week wait. I thought he was a pretty sharp old guy
> after that!
>
> Robert
>
This afternoon's excitement upstairs of my son's:
She locked herself out. Neede help calling a locksmith. Locksmith came
really fast (~20 min) and drilled out the lock (didn't go to see the
process). Charged $340. Girl was happy, then locked herself out again.
Putty knife did the job this time.
Wipe your monitor.
--
Best regards
Han
email address is invalid
"[email protected]" <[email protected]> wrote in news:01ebe6e2-
[email protected]:
> On Apr 10, 2:43 pm, Han <[email protected]> wrote:
>
>> This afternoon's excitement upstairs of my son's:
>> She locked herself out. Neede help calling a locksmith. Locksmith c
> ame
>> really fast (~20 min) and drilled out the lock (didn't go to see the
>> process). Charged $340. Girl was happy, then locked herself out aga
> in.
>> Putty knife did the job this time.
>> Wipe your monitor.
>
> LMAO!!
>
> No kidding... after that first bill, I'll bet creative thinking was in
> full gear!
>
> Robert
>
Seemed like a sweet smart college kid, but more I will not say ...
--
Best regards
Han
email address is invalid
<[email protected]> wrote in
> I will not go in, fit locks and install them, then take them off,
> store them, then go reinstall them after finishing. So when you "lock
> out" a house, you are tail end charlie.
Bingo ... and ONLY until _you_ get finished will the bank release the
remainder of the construction loan, something they will not do with a
construction door still on.
I've had houses that were *completely* finished but for the damn
construction door that only qualified for 70% release of funds as long as it
was still in place ... on a $400K project that's a damned expensive door and
hardware!
<and I hope those particular bankers are rotting somewhere in bailout hell>
--
www.e-woodshop.net
Last update: 10/22/08
KarlC@ (the obvious)
On Fri, 10 Apr 2009 22:40:03 -0700 (PDT), "[email protected]"
<[email protected]> wrote:
>On Apr 10, 10:38 pm, "DanG" <[email protected]> wrote:
>> Robert, I agree on the Porter Cable. Mine is a 1950's version. I
>> wouldn't loan it out and I'm not aware of anyone who would rent
>> one. I also would not care to take on multiple mortise locks with
>> speed bore and chisel.
>
>If I had the PC version of that vintage, I wouldn't even let anyone
>touch it, much less use it. I have only seen a small few over the
>years, and the old ones are much better made and to tighter tolerances
>than the newer ones.
>
>And no one rents those things.
>
>I don't have one myself, regardless of the age.
>
>And in fact, I only install from scratch a box lock about every 18
>months or so. It seems clients started spending more money on the
>castings and finishes, and less on the mechanical workings of
>locksets. Just doesn't seem to be much call for that type of
>installation anymore.
>
>Robert
...I bought my PC 'bout 10 years ago when I had alot of hotel
work...used it for a half-dozen box lock installs and it was
wonderful...and it still *is* wonderful as it sits in my shop waiting
to be utilized again!
cg
>
>
On Apr 10, 3:42=A0pm, "Swingman" <[email protected]> wrote:
> I've had houses that were *completely* finished but for the damn
> construction door that only qualified for 70% release of funds as long as=
it
> was still in place ... on a $400K project that's a damned expensive door =
and
> hardware!
Well, not only is that stupid on their part, but just brutal on
yours. I would probably have a stroke on the spot of that happened to
me...
I'm tellin' ya.... I ain't that strong!
> <and I hope those particular bankers are rotting somewhere in bailout hel=
l>
>
I always used to fantasize about a banker's head as a cover for a 2"
ball hitch. Think of the fun you could have with that one!
Personally, there are a few I know that I am hoping found gainful
employment in the janitorial industry. It would sure suit their skill
sets.
Robert
On Apr 10, 1:28=A0pm, "Lew Hodgett" <[email protected]> wrote:
> "scritch" wrote:
>
> .
>
> > =A0I would like to know if there is a cheap, simple way to bore for
> > the mortises that is better than hand-drilling.
>
> This is a case where "cheap" & "simple" are mutually exclusive terms.
>
> Lew
No kidding. That's a real understatement. I knew a lock guy that I
used to run into that sub contracted installation of full mortise
locks. He only installed top line Baldwins, etc. NO bored locks,
ever.
Full box mortises were all he did.
He did one to two a day in the upscale neighborhoods for several of
the high end remodelers. I was stunned when he told me what the PC
mortising machine cost and I thought he was kidding me. Nope.
Then he told me what he charged for the installation of full mortise
lock and matching deadbolt. $375 - $425.
He had a three week wait. I thought he was a pretty sharp old guy
after that!
Robert
scritch wrote:
> My brother has 17 doors in his house that need mortise locks installed.
> He wishes to cut the mortises with the doors hanging. I would like to
> know if there is a cheap, simple way to bore for the mortises that is
> better than hand-drilling. I have bored out many mortises with my drill
> press, but never free-hand.
A door lock mortising router jig sounds like what you're looking for,
but the ones made strong and safe enough to be used on a hanging door
are probably $400.
Whereas, there are several decent, inexpensive jigs meant to be used on
a door on its side.
A pair of homemade door blocks to hold the door on its side costs less
than a cup of coffee.
I can't think of too many woodworking tasks that are easier than taking
a door on and off of it's hinges. :-)
If you're installing simple cylindrical locks, you can find a decent jig
for those, that work on a hung door, for well under 50 bucks.
What are you installing?
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
-MIKE- wrote:
> scritch wrote:
>> My brother has 17 doors in his house that need mortise locks
>> installed. He wishes to cut the mortises with the doors hanging. I
>> would like to know if there is a cheap, simple way to bore for the
>> mortises that is better than hand-drilling. I have bored out many
>> mortises with my drill press, but never free-hand.
>
> A door lock mortising router jig sounds like what you're looking for,
> but the ones made strong and safe enough to be used on a hanging door
> are probably $400.
> Whereas, there are several decent, inexpensive jigs meant to be used on
> a door on its side.
>
> A pair of homemade door blocks to hold the door on its side costs less
> than a cup of coffee.
> I can't think of too many woodworking tasks that are easier than taking
> a door on and off of it's hinges. :-)
>
> If you're installing simple cylindrical locks, you can find a decent jig
> for those, that work on a hung door, for well under 50 bucks.
>
> What are you installing?
>
>
I know, I know. I would take the doors off, myself. My brother does
things his own way.
[email protected] wrote:
>> I know, I know. I would take the doors off, myself. My brother does
>> things his own way.
>
> FWIW, I do this for a living. I never bore, mortise and fit unless
> the door is hung.
>
> I actually don't know anyone that does unless they are working at the
> door plant.
>
> Robert
There ya go.
Have you found it to be easier that way, or what?
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
[email protected] wrote:
>
>> Have you found it to be easier that way, or what?
>
> A great deal easier, and more important, less hard on the door. If I
> am re-locking or retrofitting, I go in after the finishing or painting
> is done.
>
> I will not go in, fit locks and install them, then take them off,
> store them, then go reinstall them after finishing. So when you "lock
> out" a house, you are tail end charlie.
>
> 1) You cannot take a chance on scuffing or scratching finishes from
> handling doors when removing or reinstalling. No matter how careful
> you are, you will slip somewhere and the door will need a refinish.
> So you leave them on the hinges, then put the locks on in place
>
> 2) When you install a door, the installation of the frame and the door
> reveals, final placement of the door in the jamb, etc., are more of a
> feel you get rather than installing with a level or square. Twisted
> jambs, uneven floors, etc., all make the tongue/strike relation very
> relative. In a perfect world, the door is in a square frame that is
> plumb and level. You can get close, but no cigar most of the time.
> If you are in a tract home or production home, the "close" tolerance
> rule applies. You move the strike, fill the screw hole with a sliver,
> them mortise out to the new position. This is common with shop built
> doors that are fitted door-to-jamb in a plant and bored and mortised
> accordingly.
>
> If you have the door hung on site and it looks great, reveals all
> perfect, tight fit against the jambs, etc., you can mark the door for
> lock/strike location, and since you aren't moving the door, when it
> closes it will always return to the same exact place. This makes your
> measured and carefully marked door and jamb line up every time.
>
> If you mark the door and the jamb and remove the door from the jamb,
> it may not hang back the same way. With today's crappy hardware, I
> have seen many, many bent hinge pins that still work fine, but hold
> the door a certain way. If I take a door off the hinges by pin
> removal, I now label the pins. I learned this the hard way, and you
> can't seem to spot "those" hinges until it is too late. So now, look
> at the three hinged doors that are so popular. These hinges are
> pretty flimsy since they now use three instead of just two. NOTE: The
> third hinge BTW is to assist in keeping the masonite/particle board
> doors from warping in the jamb, not to make it a better door. I have
> removed doors for refinishing (oops... trim carpenter error!) that
> were these 6 panel masonite doors, and found that after working on
> them for a couple of hours they have warped on the saw horses.
>
> I don't want to wrestle with rehanging a potentially warped door,
> wagging around a door in a house to get it to my work area, or winding
> up with doors have a less than *click* close when I am finished with
> the hardware.
>
> For a guy like me, it is easier to mark, drill and chisel once to get
> a good fit. I mark, drill, then sit on a five gallon paint bucket and
> do the rest of the fitting. Also, when drilling the tongue cylinder,
> I find it much easier to gauge left and right by keeping the drill
> parallel to the door by doing it this way.
> Depending on the lock/latch/strike, I can go start to finish (marking
> to final adjustment) in +/- 30 minutes.
>
> In the end, the door isn't moved so the finish isn't in danger (no $$$
> for finish repair, even if it someone else that knocks over the door
> or drags their nail bags across it), and it always goes back to the
> original spot after the hardware is prepped and installed.
>
> Robert
Next time, be more thorough, will ya? :-)
I suppose with 17 doors, the OP should start on the least seen door,
and 3-4 doors in, will have the drill down and the rest will be perfect.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
[email protected] wrote:
> On Apr 10, 3:42Â pm, "Swingman" <[email protected]> wrote:
>
>> I've had houses that were *completely* finished but for the damn
>> construction door that only qualified for 70% release of funds as long as
>> it was still in place ... on a $400K project that's a damned expensive
>> door and hardware!
>
> Well, not only is that stupid on their part, but just brutal on
> yours. I would probably have a stroke on the spot of that happened to
> me...
>
> I'm tellin' ya.... I ain't that strong!
>
>> <and I hope those particular bankers are rotting somewhere in bailout
>> hell>
>>
>
> I always used to fantasize about a banker's head as a cover for a 2"
> ball hitch. Think of the fun you could have with that one!
>
> Personally, there are a few I know that I am hoping found gainful
> employment in the janitorial industry. It would sure suit their skill
> sets.
>
> Robert
I once got over good on a bank. I felt good for years. It was all legal and
knew they didn't know what a piece of equipment was worth. I ended up
getting 3 pieces that were worth 60,000.00 for 6800.00. Ive told the story
at least 100 times and it still brings a smile to my face. :)
--
"You can lead them to LINUX
but you can't make them THINK"
Running Mandriva release 2008.0 free-i586 using KDE on i586
Website Address http://rentmyhusband.biz/
"scritch" <[email protected]> wrote in message news:[email protected]...
> -MIKE- wrote:
>> scritch wrote:
>>> My brother has 17 doors in his house that need mortise locks installed.
>>> He wishes to cut the mortises with the doors hanging. I would like to
>>> know if there is a cheap, simple way to bore for the mortises that is
>>> better than hand-drilling. I have bored out many mortises with my drill
>>> press, but never free-hand.
>>
>> A door lock mortising router jig sounds like what you're looking for,
>> but the ones made strong and safe enough to be used on a hanging door
>> are probably $400.
>> Whereas, there are several decent, inexpensive jigs meant to be used on
>> a door on its side.
>>
>> A pair of homemade door blocks to hold the door on its side costs less
>> than a cup of coffee.
>> I can't think of too many woodworking tasks that are easier than taking
>> a door on and off of it's hinges. :-)
>>
>> If you're installing simple cylindrical locks, you can find a decent jig
>> for those, that work on a hung door, for well under 50 bucks.
>>
>> What are you installing?
>>
>>
> I know, I know. I would take the doors off, myself. My brother does
> things his own way.
LOL. I think I would let him do things.
Max