The job that inspired my previous posts about drawer slides and
soft-close adapters has been completed with great success and client
satisfaction.
I ended up taking accurate measurements of the inside width of the
cabinet boxes, calculating the space needed for the drawers/slides
combined width, and fabricating custom spacers in my shop. I also had
to do a bit of surgery on one cabinet because the drawer opening was
about 1/8" too narrow. Fein MultiMaster to the rescue!!
Thanks to everyone for the advice and recommendations.
The KV8500 slides were indeed very heavy duty and up to the task. I
have some reservations about the plastic parts on them, but I'll hold
off judgment until I get called back because one of them broke. :-)
The jury is also still out on the soft-close adapters but they seem to
function well. Time will tell.
Everything took me thrice as long as I initially thought it would-- par
for the course for new ventures like this. But I picked up some skills
and knowledge that will help the next repair job go a lot faster.
Bottom line is the client was thrilled. Check out this review they left
for me on the Thumbtack website I use for leads...
-------------------------------
5/5 Stars
"He redid our slides for our cabinets. They were breaking constantly and
we didn't know if they were fixable. When Mike came to look at them, he
talked to us about everything that was wrong with them and what he could
do to make them work again. He was AMAZING! If anyone were to ask for a
handyman contact I would give them his information immediately. He is
VERY trustworthy & works very hard. You can also tell he loves what he
does and he wants to make sure every job he does he completes 110%. He
is amazing!!!"
-------------------------------
I'll take it. :-)
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On 2/24/2016 3:45 PM, -MIKE- wrote:
> I also had
> to do a bit of surgery on one cabinet because the drawer opening was
> about 1/8" too narrow. Fein MultiMaster to the rescue!!
In that situation I have been known to set the table saw blade the same
height as the drawer side drawer slide, set the fence, run the whole
drawer though, shaving off 1/16" off each drawer side.
That 1/16" deep "dado" just cut is nicely hidden by the drawer slide.
> Thanks to everyone for the advice and recommendations.
> The KV8500 slides were indeed very heavy duty and up to the task. I
> have some reservations about the plastic parts on them, but I'll hold
> off judgment until I get called back because one of them broke. :-) The
> jury is also still out on the soft-close adapters but they seem to
> function well. Time will tell.
Been using KV's exclusively for years and have never had a call back due
to the plastic bits.
I have indeed broken some when forcing improperly installed drawers open
as a last resort, but, with the non-handed design, it is usually an
easy, no adjustment, replacement.
> Everything took me thrice as long as I initially thought it would-- par
> for the course for new ventures like this. But I picked up some skills
> and knowledge that will help the next repair job go a lot faster. Bottom
> line is the client was thrilled. Check out this review they left for me
> on the Thumbtack website I use for leads...
>
> -------------------------------
> 5/5 Stars
> "He redid our slides for our cabinets. They were breaking constantly and
> we didn't know if they were fixable. When Mike came to look at them, he
> talked to us about everything that was wrong with them and what he could
> do to make them work again. He was AMAZING! If anyone were to ask for a
> handyman contact I would give them his information immediately. He is
> VERY trustworthy & works very hard. You can also tell he loves what he
> does and he wants to make sure every job he does he completes 110%. He
> is amazing!!!"
> -------------------------------
>
> I'll take it. :-)
Nothing more, other than that the check went through, need be said. ;)
Good job!
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
On Thu, 25 Feb 2016 15:28:24 -0500, "Lee Michaels"
<leemichaels*nadaspam* at comcast dot net> wrote:
>
>
>"Leon" <lcb11211@swbelldotnet> wrote
>>
>> I am just now realizing that anything I do takes 3 times as long as it
>> seems that it should. LOL
>>
>Yep, standard rule of thumb for me. figure out how long it takes to do the
>job. Multiply times three. That is about right. Except anything that my
>wife is involved with. You can tack on another 50% to those jobs.
I had a boss once tell me that for a realistic development schedule,
one should double the digits and increment the units, so a job that we
think should take a day, gets double to two days, then the days
incremented so the estimate should be two weeks. Somehow, he never
bought it when we used the process, though.
>
>And then there are those jobs that never seem to get done. Those are
>referred to as the FOREVER JOBS.
>
>
"-MIKE-" <[email protected]> wrote
>
> Everything took me thrice as long as I initially thought it would-- par
> for the course for new ventures like this. But I picked up some skills
> and knowledge that will help the next repair job go a lot faster. Bottom
> line is the client was thrilled. Check out this review they left for me
> on the Thumbtack website I use for leads...
>
> -------------------------------
> 5/5 Stars
> "He redid our slides for our cabinets. They were breaking constantly and
> we didn't know if they were fixable. When Mike came to look at them, he
> talked to us about everything that was wrong with them and what he could
> do to make them work again. He was AMAZING! If anyone were to ask for a
> handyman contact I would give them his information immediately. He is VERY
> trustworthy & works very hard. You can also tell he loves what he does and
> he wants to make sure every job he does he completes 110%. He is
> amazing!!!"
> -------------------------------
>
> I'll take it. :-)
>
It doesn't get better than this for a recommendation. Kudos to you Mike.
You earned it.
"Leon" <lcb11211@swbelldotnet> wrote
>
> I am just now realizing that anything I do takes 3 times as long as it
> seems that it should. LOL
>
Yep, standard rule of thumb for me. figure out how long it takes to do the
job. Multiply times three. That is about right. Except anything that my
wife is involved with. You can tack on another 50% to those jobs.
And then there are those jobs that never seem to get done. Those are
referred to as the FOREVER JOBS.
On 2/25/2016 2:28 PM, Lee Michaels wrote:
> And then there are those jobs that never seem to get done. Those are
> referred to as the FOREVER JOBS.
Around here they're known as "if you want that done, do it yourself" jobs.
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
On 2/24/2016 4:57 PM, Swingman wrote:
> On 2/24/2016 3:45 PM, -MIKE- wrote:
>
>> I also had
>> to do a bit of surgery on one cabinet because the drawer opening was
>> about 1/8" too narrow. Fein MultiMaster to the rescue!!
>
> In that situation I have been known to set the table saw blade the same
> height as the drawer side drawer slide, set the fence, run the whole
> drawer though, shaving off 1/16" off each drawer side.
Exactly! ;~) and just one more good reason to mount the drawer side of
the slide near or at the bottom of the drawer vs. midway.
>
> That 1/16" deep "dado" just cut is nicely hidden by the drawer slide.
Now you lost me. Dado? I was thinking sort'a of a rabbet.
On 2/24/2016 3:45 PM, -MIKE- wrote:
> The job that inspired my previous posts about drawer slides and
> soft-close adapters has been completed with great success and client
> satisfaction.
>
> I ended up taking accurate measurements of the inside width of the
> cabinet boxes, calculating the space needed for the drawers/slides
> combined width, and fabricating custom spacers in my shop. I also had
> to do a bit of surgery on one cabinet because the drawer opening was
> about 1/8" too narrow. Fein MultiMaster to the rescue!!
>
> Thanks to everyone for the advice and recommendations.
> The KV8500 slides were indeed very heavy duty and up to the task. I
> have some reservations about the plastic parts on them, but I'll hold
> off judgment until I get called back because one of them broke. :-) The
> jury is also still out on the soft-close adapters but they seem to
> function well. Time will tell.
FWIW all slides have plastic parts, at least all of the ones that I have
seen.
>
> Everything took me thrice as long as I initially thought it would-- par
> for the course for new ventures like this. But I picked up some skills
> and knowledge that will help the next repair job go a lot faster. Bottom
> line is the client was thrilled. Check out this review they left for me
> on the Thumbtack website I use for leads...
I am just now realizing that anything I do takes 3 times as long as it
seems that it should. LOL
>
> -------------------------------
> 5/5 Stars
> "He redid our slides for our cabinets. They were breaking constantly and
> we didn't know if they were fixable. When Mike came to look at them, he
> talked to us about everything that was wrong with them and what he could
> do to make them work again. He was AMAZING! If anyone were to ask for a
> handyman contact I would give them his information immediately. He is
> VERY trustworthy & works very hard. You can also tell he loves what he
> does and he wants to make sure every job he does he completes 110%. He
> is amazing!!!"
> -------------------------------
>
> I'll take it. :-)
>
>
You sure should!!! Did you explain that completing 110% is a benefit
for you too? ;~) No go backs! Glad to hear you had a great out come.
On Wednesday, February 24, 2016 at 3:45:55 PM UTC-6, -MIKE- wrote:
> The KV8500 slides were indeed very heavy duty and up to the task. I=20
> have some reservations about the plastic parts on them, but I'll hold=20
> off judgment until I get called back because one of them broke. :-)=20
> The jury is also still out on the soft-close adapters but they seem to=20
> function well. Time will tell.
I am glad you like them. The client with the picture of the floating drawe=
r was in touch with me this week and he told me that it is still in perfect=
alignment and working as designed, even on full extension. I was trying t=
o remember back a few decades when KV was about the only drawer slides read=
ily available in small quantities, and it seems to me even back in the 70's=
they had plastic parts. They were white plastic stops on the rear end of =
the slide and black plastic on the front. Couldn't say for sure, but I can=
say I would seriously doubt you will have any problems with those slides.
Good on 'ya for the good work and excellent review. Nothing sells more wor=
k like a happy client, and no doubt you deserved the pat on the back!
Robert
On Wed, 24 Feb 2016 15:45:49 -0600, -MIKE- <[email protected]>
wrote:
>The job that inspired my previous posts about drawer slides and
>soft-close adapters has been completed with great success and client
>satisfaction.
>
>I ended up taking accurate measurements of the inside width of the
>cabinet boxes, calculating the space needed for the drawers/slides
>combined width, and fabricating custom spacers in my shop. I also had
>to do a bit of surgery on one cabinet because the drawer opening was
>about 1/8" too narrow. Fein MultiMaster to the rescue!!
>
>Thanks to everyone for the advice and recommendations.
>The KV8500 slides were indeed very heavy duty and up to the task. I
>have some reservations about the plastic parts on them, but I'll hold
>off judgment until I get called back because one of them broke. :-)
>The jury is also still out on the soft-close adapters but they seem to
>function well. Time will tell.
>
>Everything took me thrice as long as I initially thought it would-- par
>for the course for new ventures like this. But I picked up some skills
>and knowledge that will help the next repair job go a lot faster.
>Bottom line is the client was thrilled. Check out this review they left
>for me on the Thumbtack website I use for leads...
>
>-------------------------------
>5/5 Stars
>"He redid our slides for our cabinets. They were breaking constantly and
>we didn't know if they were fixable. When Mike came to look at them, he
>talked to us about everything that was wrong with them and what he could
>do to make them work again. He was AMAZING! If anyone were to ask for a
>handyman contact I would give them his information immediately. He is
>VERY trustworthy & works very hard. You can also tell he loves what he
>does and he wants to make sure every job he does he completes 110%. He
>is amazing!!!"
>-------------------------------
>
>I'll take it. :-)
And you should, congratulations!
On 2/24/16 4:57 PM, Swingman wrote:
> On 2/24/2016 3:45 PM, -MIKE- wrote:
>
>> I also had
>> to do a bit of surgery on one cabinet because the drawer opening was
>> about 1/8" too narrow. Fein MultiMaster to the rescue!!
>
> In that situation I have been known to set the table saw blade the same
> height as the drawer side drawer slide, set the fence, run the whole
> drawer though, shaving off 1/16" off each drawer side.
>
> That 1/16" deep "dado" just cut is nicely hidden by the drawer slide.
>
I did that last time I changed slides in my own house!!
In this case, I would've had to take the drawer back to the shop and do
that.
The cut is all sanded smooth, so you can hardly tell unless you look
very close at it. The drawer fronts cover it, too.
>> Thanks to everyone for the advice and recommendations.
>> The KV8500 slides were indeed very heavy duty and up to the task. I
>> have some reservations about the plastic parts on them, but I'll hold
>> off judgment until I get called back because one of them broke. :-) The
>> jury is also still out on the soft-close adapters but they seem to
>> function well. Time will tell.
>
> Been using KV's exclusively for years and have never had a call back due
> to the plastic bits.
>
Good to hear!
> I have indeed broken some when forcing improperly installed drawers open
> as a last resort, but, with the non-handed design, it is usually an
> easy, no adjustment, replacement.
>
>> Everything took me thrice as long as I initially thought it would-- par
>> for the course for new ventures like this. But I picked up some skills
>> and knowledge that will help the next repair job go a lot faster. Bottom
>> line is the client was thrilled. Check out this review they left for me
>> on the Thumbtack website I use for leads...
>>
>> -------------------------------
>> 5/5 Stars
>> "He redid our slides for our cabinets. They were breaking constantly and
>> we didn't know if they were fixable. When Mike came to look at them, he
>> talked to us about everything that was wrong with them and what he could
>> do to make them work again. He was AMAZING! If anyone were to ask for a
>> handyman contact I would give them his information immediately. He is
>> VERY trustworthy & works very hard. You can also tell he loves what he
>> does and he wants to make sure every job he does he completes 110%. He
>> is amazing!!!"
>> -------------------------------
>>
>> I'll take it. :-)
>
> Nothing more, other than that the check went through, need be said. ;)
>
> Good job!
>
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On 2/25/16 8:25 AM, Lee Michaels wrote:
>
>
> "-MIKE-" <[email protected]> wrote
>>
>> Everything took me thrice as long as I initially thought it would--
>> par for the course for new ventures like this. But I picked up some
>> skills and knowledge that will help the next repair job go a lot
>> faster. Bottom line is the client was thrilled. Check out this review
>> they left for me on the Thumbtack website I use for leads...
>>
>> -------------------------------
>> 5/5 Stars
>> "He redid our slides for our cabinets. They were breaking constantly
>> and we didn't know if they were fixable. When Mike came to look at
>> them, he talked to us about everything that was wrong with them and
>> what he could do to make them work again. He was AMAZING! If anyone
>> were to ask for a handyman contact I would give them his information
>> immediately. He is VERY trustworthy & works very hard. You can also
>> tell he loves what he does and he wants to make sure every job he does
>> he completes 110%. He is amazing!!!"
>> -------------------------------
>>
>> I'll take it. :-)
>>
> It doesn't get better than this for a recommendation. Kudos to you
> Mike. You earned it.
>
Plus, I got a tip! :-)
Thanks.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On 2/25/16 9:35 PM, [email protected] wrote:
> On Wednesday, February 24, 2016 at 3:45:55 PM UTC-6, -MIKE- wrote:
>
>> The KV8500 slides were indeed very heavy duty and up to the task.
>> I have some reservations about the plastic parts on them, but I'll
>> hold off judgment until I get called back because one of them
>> broke. :-) The jury is also still out on the soft-close adapters
>> but they seem to function well. Time will tell.
>
> I am glad you like them. The client with the picture of the floating
> drawer was in touch with me this week and he told me that it is still
> in perfect alignment and working as designed, even on full extension.
> I was trying to remember back a few decades when KV was about the
> only drawer slides readily available in small quantities, and it
> seems to me even back in the 70's they had plastic parts. They were
> white plastic stops on the rear end of the slide and black plastic on
> the front. Couldn't say for sure, but I can say I would seriously
> doubt you will have any problems with those slides.
>
Good to hear!
I told them I'd stand by my work and the slides had a 15 year
manufacture warranty.
> Good on 'ya for the good work and excellent review. Nothing sells
> more work like a happy client, and no doubt you deserved the pat on
> the back!
>
> Robert
>
Tanks a rot.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply