>Workers should not be elevated on the forks of a forklift. A forklift
>doesn't have a holding (lock) valve in the lift system and is not designed
>for a person to be on or under forks if elevated. If some one gets hurt
>you will be open to some major legal problems if in the U.S.. You can rent
>"manlifts" and "safety harness plus lanyard" for hoisting personal.
Or you can review the regs. It's ok to lift people with a forklift if
a) They are on a lifting platform that is secured to the lift
<<and>>
b) That platform has a proper guardrail.
With the proper rail, a harness isn't required.
http://www.osha.gov/pls/oshaweb/owadisp.show_document?p_table=INTERPRETATIONS&p_id=21322
Running out to rent a scissor lift or some equivilent peice of
machinery every time a lightbulb needed changing would really put a
ding in a small shop's budget.
>Workers should not be elevated on the forks of a forklift. A forklift
>doesn't have a holding (lock) valve in the lift system and is not designed
>for a person to be on or under forks if elevated. If some one gets hurt
>you will be open to some major legal problems if in the U.S.. You can rent
>"manlifts" and "safety harness plus lanyard" for hoisting personal.
Or you can review the regs. It's ok to lift people with a forklift if
a) They are on a lifting platform that is secured to the lift
<<and>>
b) That platform has a proper guardrail.
With the proper rail, a harness isn't required.
http://www.osha.gov/pls/oshaweb/owadisp.show_document?p_table=INTERPRETATIONS&p_id=21322
Running out to rent a scissor lift or some equivilent peice of
machinery every time a lightbulb needed changing would really put a
ding in a small shop's budget.
couillion wrote:
> "stoutman" <.@.> wrote in message
> news:[email protected]...
> >
> >> If some one gets hurt you will be open to some major legal
> >> problems if in the U.S..
> >
> > Not if he is employing illegal aliens. They are not likely to sue.
> >
>
> not necessarily so....
>
> http://www.libertymatters.org/newsservice/2005/faxback/2873_Ranch.htm
Given that two of the defendants didn't even defend themselves and
the third settled out of court that isn't much of a 'precedent'.
Back in the early days of the Icelandic Allthing there were basicly
two punishments. One was a fine. For example, if someone murdered
your brother they might be required to pay you 200 pieces of gold.
But if you wound up supporting his widow and children, or if the
murder was particularly foul, like backstabbing then that might
be increased. OTOH, if your brother was kind of a jerk the fine
might be reduced and if he had it comming to him, no compensation
would be required.
The second punishment was outlawry. If the wrongdoer could not
pay or refused to pay the fine then he was declared an outlaw which
meant you could kill him and not be fined.
Outlawry has long passed into the history books. Today, no matter
how evil a person is, it is still possible to commit a crime (or a
tort)
against him and be punished for it.
Not to conclude that the defendants in the suit above actually did
committ the tort in question but if someone does commit a tort
agains an illegal alien there is no reason why they should not be
allowed to sue, same as anybody else, and then be deported right
after they collect.
--
FF
On Wed, 26 Apr 2006 13:11:06 GMT, "Evon Barvinchack"
<[email protected]> wrote:
>Does anyone know the approx. wt of a treated 4x8 3/4" sheet of plywood? I'm
>making a box for my forklift and need to figure my max wt lift. Thanks in
>advance.
Since the species and moisture content are unknown the worst case
would be to assume it's 100% water. The volume is 2 cu ft, so figure
the weight as 2 * 62 lb.
"stoutman" <.@.> wrote in message
news:[email protected]...
>
>> If some one gets hurt you will be open to some major legal
>> problems if in the U.S..
>
> Not if he is employing illegal aliens. They are not likely to sue.
>
not necessarily so....
http://www.libertymatters.org/newsservice/2005/faxback/2873_Ranch.htm
"Evon Barvinchack" <[email protected]> wrote in message
news:[email protected]...
> Does anyone know the approx. wt of a treated 4x8 3/4" sheet of plywood?
> I'm
> making a box for my forklift and need to figure my max wt lift. Thanks in
> advance.
>
>
> ----------------------------------------------------------------------------
> ----
80-100lbs if still wet
That said, if you are operating your fork lift to within the weight of a
piece of plywood of its limits, you are operation in dangerous territory.
[email protected] wrote:
>> Workers should not be elevated on the forks of a forklift. A forklift
>> doesn't have a holding (lock) valve in the lift system and is not designed
>> for a person to be on or under forks if elevated. If some one gets hurt
>> you will be open to some major legal problems if in the U.S.. You can rent
>> "manlifts" and "safety harness plus lanyard" for hoisting personal.
>
> Or you can review the regs. It's ok to lift people with a forklift if
>
> a) They are on a lifting platform that is secured to the lift
> <<and>>
> b) That platform has a proper guardrail.
And shame if you don't.
Like the guys in this German safety video.
http://media.hugi.is/hahradi/fyndnar/STAPLERFAHRERKLAUSDERERSTEA.wmv
Endure the opening scenes,
the real fun starts around 01:45.
--
TomH [ antonomasia <at> gmail <dot> com ]
Thanks for your replies. I want to plug in the wt of a worker, tools,
material and the wt of plywood box. I wanted to make sure that the total
weight did'nt exceed it's safe lift capacity. As the plywood dries it will
become lighter. Just trying to out smart "Murphy's Law"!
"Wes Stewart" <n7ws*@*yahoo.com> wrote in message
news:[email protected]...
> On Wed, 26 Apr 2006 13:11:06 GMT, "Evon Barvinchack"
> <[email protected]> wrote:
>
> >Does anyone know the approx. wt of a treated 4x8 3/4" sheet of plywood?
I'm
> >making a box for my forklift and need to figure my max wt lift. Thanks
in
> >advance.
>
> Since the species and moisture content are unknown the worst case
> would be to assume it's 100% water. The volume is 2 cu ft, so figure
> the weight as 2 * 62 lb.
----------------------------------------------------------------------------
----
On Wed, 26 Apr 2006 14:38:02 +0000, Evon Barvinchack wrote:
> Thanks for your replies. I want to plug in the wt of a worker, tools,
> material and the wt of plywood box. I wanted to make sure that the total
> weight did'nt exceed it's safe lift capacity. As the plywood dries it will
> become lighter. Just trying to out smart "Murphy's Law"!
Workers should not be elevated on the forks of a forklift. A forklift
doesn't have a holding (lock) valve in the lift system and is not designed
for a person to be on or under forks if elevated. If some one gets hurt
you will be open to some major legal problems if in the U.S.. You can rent
"manlifts" and "safety harness plus lanyard" for hoisting personal.
Check with a local forklift dealer or a rental outfit that supplies
construction equipment for more info. It's worth having the right tool for
the job in the first place.