Hello Looking for advise. I posted here a while ago about a wobble in the
blade on my tablesaw. I bought a new blade , but no different. Below are
emails I traded with Ridgid. Do you think this could be the case? Start with
the bottom email from me 1st.
Thanks for any feedback. Chris
Chris:
A lot of the blades on the market these days have laser cuts to aid in
balance and cooling, so the wobble appearance you are seeing is normal, and
the service centers determination that the arbor is not the cause is
somewhat confirmed by your visual verification of an appeared wobble on slow
down. A blade with laser cuts trues up at full RPM, but appears to have a
wobble upon start up and slow down.
The burning you are experiencing is possibly due to a needed adjustment.
With the blade elevated all the way up, take and measure from the edge of
the miter slot in the table over to a tooth at the front of the blade. Then
measure to a tooth at the rear of the blade. You possibly will find a
difference in the measurement.
Now measure from the same tooth at the front of the blade, mark it with a
marker and rotate it to the rear position. If the measurement is not the
same front and back to the same tooth, the blade carriage/cradle needs to be
adjusted (see manual) to bring the face of the blade into square with the
slot.
Let me know what you find.
T.Clinkscales
Technical Services
One World Technologies, Inc.
-----Original Message-----
From: Chris Fitzpatrick [mailto:[email protected]]
Sent: Wednesday, February 16, 2005 10:27 AM
To: [email protected]
Subject: RE: RGDChris Fitzpatrick:RE: Table Saw
Hello Tom,
Thanks for your prompt response. I am not at home now, so I will have to get
back to you with the model # of the saw. The blade is not the original, as I
said I bought a new blade when I realized I had a problem, I'll be happy to
tell you what that is too. You should be able to trust your service center I
agree, but it's not a perfect world and things happen. I had not even
mentioned it, but the top of the saw is a mess now, I don't now where they
had it or what they had on it but I will have a big job cleaning the cast
iron top. I am certain the wobble is NOT the blade. This wobble is not
noticeable when the saw is running full speed, at least not to me. As the
saw coasts to a stop you can see what it wobble. I don't have an Inca tool
for measuring the blade distance as it turns, but when I place a piece a
wood against the blade and rotate it by hand, I would say there is about 1/8
th of a difference from one side to another. I tried to figure out why I was
having problems with my saw, so I consulted other woodworkers to see if my
experience was normal. I now believe it's not. You must have someone who
could look at the saw for me. I will be happy to pay for their time if I'm
wrong, but I truly believe I'm not. I really want to continue to use it, and
if I was a contractor ripping rough lumber maybe I could, but cutting oak,
maple etc is just way to difficult. I read of other people cutting these
woods easily without burning. A blade should not wobble as it moves. A
tolerance a a few hundredths of an inch is unavoidable, but not an 1/8.
Thanks,
Chris
>From: Tom Clinkscales <[email protected]>
>To: "'[email protected]'" <[email protected]>
>Subject: RGDChris Fitzpatrick:RE: Table Saw
>Date: Wed, 16 Feb 2005 08:55:02 -0500
>
>Mr. Fitzpatrick:
>
>If a Ridgid authorized warranty service dealer determined there was nothing
>wrong with the arbor, we have to stand by their determination since they
are
>our eyes and ears out there in the field. If they determined the wobble is
>not coming from the arbor, then it may be the blade flanges, which they
>should have also checked. It could also be the set up of the saw causing
the
>burning, not necessarily what appears as wobble with the blade.
>
>What is the model number of the saw? Are you using the stock blade? When
are
>you seeing the wobble in the blade, at full speed or as it starts up or
>slows down?
>
>T.Clinkscales
>Technical Services
>One World Technologies, Inc.
>
>
>
>
>
>
>
>
>-----Original Message-----
>From: [email protected] [mailto:[email protected]]
>Sent: Tuesday, February 15, 2005 9:22 PM
>To: [email protected]
>Subject: Table Saw
>
>
>Hello , I purchased a table saw from HD about 2 1/2 years ago when I
thought
>I would be interested in woodworking. My interest has grown and I realized
a
>while ago that my table saw should be able to cut oak etc without burn
marks
>etc. After a close inspection I realized there was a wobble in the blade,
so
>I bougt a new blade, still a wobble. It would seem there is a problem with
>the arbor? I called customer service and was told to bring the saw to a
>ridgid service center in my area. THe place is A&T tool in Huntington. I
>dropped off my saw before Christmas as I was going away on vacation for 6
>weeks. When I returned I called & they said it was all done. So I picked it
>up, asked what they found, but the guy who worked on it was off and all
they
>said was it was done. I came home plugged it in, still wobbles. I've now
>found out they found nothing wrong with it. Can you imagine how hard it was
>for me to move my table saw to this place, then bring it home to find out
>they did nothing? What am I to do? Anyone who knows anything about a table
>saw would know that for a blade to wobble means trouble. I'm really into
>woodwork now & this is a problem. Can you please help me? I can't even sell
>it because I would feel bad about sending someone thru what I've been thru.
Chris wrote:
> Hello Looking for advise. I posted here a while ago about a wobble in
the
> blade on my tablesaw. I bought a new blade , but no different. Below
are
> emails I traded with Ridgid. Do you think this could be the case?
Start with
> the bottom email from me 1st.
Chris, something is way off - either in Home depot response or in your
assessment of the problem.
I had some early experience chasing alignment problems with my table
saw and learned a lot. I'd be happy to share with you what I know. It
would be more efficient in email or on the phone. I was so successful
in documenting the problem that Jet replaced my whole saw and set it up
for me at no charge.
Contact me by direct email. I'll be happy to call and talk it over with
you.
My email address is wrobertdavis AT yahoo DOT com.
Bob Davis
Chris wrote:
>
> Hello Looking for advise. I posted here a while ago about a wobble in the
> blade on my tablesaw. I bought a new blade , but no different. Below are
> emails I traded with Ridgid. Do you think this could be the case? Start with
> the bottom email from me 1st.
>
> Thanks for any feedback. Chris
Far too long and disjointed to go through the entirety but...
Any chance the arbor isn't turned all the way to the plate or the blade
hole isn't completely reamed? Ran into the latter w/ an Incra blade
(from the Orange Box place) that was apparently slightly under
5/8"--wouldn't <quite> pull up on the shaft of my old Powermatic 66--in
30 years, only blade that ever happened with so am pretty sure can't
blame it on the saw... :)
I seem to have seen something wrt to Ridgid that there were a few models
w/ a groove on the arbor that allowed a blade to drop into...Ridgid will
replace that--seems like I saw that in recent FWW comments page.
If there's 1/8" runout on a blade turning it by hand it shouldn't be at
all difficult to detect where it's coming from w/ only a modicum of
inspection and measurement. If, otoh there's no perceptible runout at
speed (as I infer from a later point in the quick scan) then it doesn't
seem there's a problem of such a large magnitude...
Chris
Did you over tighten the nut? Loosen it and see if the wobble goes away or
gets better.
max
> Chris wrote:
>>
>> Hello Looking for advise. I posted here a while ago about a wobble in the
>> blade on my tablesaw. I bought a new blade , but no different. Below are
>> emails I traded with Ridgid. Do you think this could be the case? Start with
>> the bottom email from me 1st.
>>
>> Thanks for any feedback. Chris
>
> Far too long and disjointed to go through the entirety but...
>
> Any chance the arbor isn't turned all the way to the plate or the blade
> hole isn't completely reamed? Ran into the latter w/ an Incra blade
> (from the Orange Box place) that was apparently slightly under
> 5/8"--wouldn't <quite> pull up on the shaft of my old Powermatic 66--in
> 30 years, only blade that ever happened with so am pretty sure can't
> blame it on the saw... :)
>
> I seem to have seen something wrt to Ridgid that there were a few models
> w/ a groove on the arbor that allowed a blade to drop into...Ridgid will
> replace that--seems like I saw that in recent FWW comments page.
>
> If there's 1/8" runout on a blade turning it by hand it shouldn't be at
> all difficult to detect where it's coming from w/ only a modicum of
> inspection and measurement. If, otoh there's no perceptible runout at
> speed (as I infer from a later point in the quick scan) then it doesn't
> seem there's a problem of such a large magnitude...
Thanks a lot, I will contact you shortly.
Chris
<[email protected]> wrote in message
news:[email protected]...
>
> Chris wrote:
> > Hello Looking for advise. I posted here a while ago about a wobble in
> the
> > blade on my tablesaw. I bought a new blade , but no different. Below
> are
> > emails I traded with Ridgid. Do you think this could be the case?
> Start with
> > the bottom email from me 1st.
>
> Chris, something is way off - either in Home depot response or in your
> assessment of the problem.
>
> I had some early experience chasing alignment problems with my table
> saw and learned a lot. I'd be happy to share with you what I know. It
> would be more efficient in email or on the phone. I was so successful
> in documenting the problem that Jet replaced my whole saw and set it up
> for me at no charge.
>
> Contact me by direct email. I'll be happy to call and talk it over with
> you.
>
> My email address is wrobertdavis AT yahoo DOT com.
>
> Bob Davis
>
On Wed, 16 Feb 2005 16:05:46 -0500, "Chris" <[email protected]>
wrote:
>Hello Looking for advise. I posted here a while ago about a wobble in the
>blade on my tablesaw. I bought a new blade , but no different. Below are
>emails I traded with Ridgid. Do you think this could be the case? Start with
>the bottom email from me 1st.
>
>Thanks for any feedback. Chris
Sorry to hear of your problems.
If the saw is not under warranty, see if you can find a reputable
shop in your area that will work on it. Have them check it out and
give you an estimate.
If it is still under warranty you may want to do the same thing.
Ask what they will charge to diagnose the problem. If it's affordable
enough, have them give you a written report. If they do find a
problem you can present this info to Rigid for the warranty work.
Mike O.
Sure. It could be.
No one can know if the arbor has run-out without measuring it.
Either trust them and accept that the problem is in the blade, or have it
checked by someone capable of checking it.
-j
"Chris" <[email protected]> wrote in message
news:cFOQd.5068$%[email protected]...
> Hello Looking for advise. I posted here a while ago about a wobble in the
> blade on my tablesaw. I bought a new blade , but no different. Below are
> emails I traded with Ridgid. Do you think this could be the case? Start
with
> the bottom email from me 1st.
>
> Thanks for any feedback. Chris
>
>
>
> Chris:
>
> A lot of the blades on the market these days have laser cuts to aid in
> balance and cooling, so the wobble appearance you are seeing is normal,
and
> the service centers determination that the arbor is not the cause is
> somewhat confirmed by your visual verification of an appeared wobble on
slow
> down. A blade with laser cuts trues up at full RPM, but appears to have a
> wobble upon start up and slow down.
>
> The burning you are experiencing is possibly due to a needed adjustment.
>
> With the blade elevated all the way up, take and measure from the edge of
> the miter slot in the table over to a tooth at the front of the blade.
Then
> measure to a tooth at the rear of the blade. You possibly will find a
> difference in the measurement.
>
> Now measure from the same tooth at the front of the blade, mark it with a
> marker and rotate it to the rear position. If the measurement is not the
> same front and back to the same tooth, the blade carriage/cradle needs to
be
> adjusted (see manual) to bring the face of the blade into square with the
> slot.
>
> Let me know what you find.
>
> T.Clinkscales
> Technical Services
> One World Technologies, Inc.
>
>
>
>
>
>
>
> -----Original Message-----
> From: Chris Fitzpatrick [mailto:[email protected]]
> Sent: Wednesday, February 16, 2005 10:27 AM
> To: [email protected]
> Subject: RE: RGDChris Fitzpatrick:RE: Table Saw
>
>
> Hello Tom,
>
> Thanks for your prompt response. I am not at home now, so I will have to
get
> back to you with the model # of the saw. The blade is not the original, as
I
> said I bought a new blade when I realized I had a problem, I'll be happy
to
> tell you what that is too. You should be able to trust your service center
I
> agree, but it's not a perfect world and things happen. I had not even
> mentioned it, but the top of the saw is a mess now, I don't now where they
> had it or what they had on it but I will have a big job cleaning the cast
> iron top. I am certain the wobble is NOT the blade. This wobble is not
> noticeable when the saw is running full speed, at least not to me. As the
> saw coasts to a stop you can see what it wobble. I don't have an Inca tool
> for measuring the blade distance as it turns, but when I place a piece a
> wood against the blade and rotate it by hand, I would say there is about
1/8
> th of a difference from one side to another. I tried to figure out why I
was
> having problems with my saw, so I consulted other woodworkers to see if my
> experience was normal. I now believe it's not. You must have someone who
> could look at the saw for me. I will be happy to pay for their time if I'm
> wrong, but I truly believe I'm not. I really want to continue to use it,
and
> if I was a contractor ripping rough lumber maybe I could, but cutting oak,
> maple etc is just way to difficult. I read of other people cutting these
> woods easily without burning. A blade should not wobble as it moves. A
> tolerance a a few hundredths of an inch is unavoidable, but not an 1/8.
>
>
>
> Thanks,
>
> Chris
>
>
>
>
>
> >From: Tom Clinkscales <[email protected]>
> >To: "'[email protected]'" <[email protected]>
> >Subject: RGDChris Fitzpatrick:RE: Table Saw
> >Date: Wed, 16 Feb 2005 08:55:02 -0500
> >
> >Mr. Fitzpatrick:
> >
> >If a Ridgid authorized warranty service dealer determined there was
nothing
> >wrong with the arbor, we have to stand by their determination since they
> are
> >our eyes and ears out there in the field. If they determined the wobble
is
> >not coming from the arbor, then it may be the blade flanges, which they
> >should have also checked. It could also be the set up of the saw causing
> the
> >burning, not necessarily what appears as wobble with the blade.
> >
> >What is the model number of the saw? Are you using the stock blade? When
> are
> >you seeing the wobble in the blade, at full speed or as it starts up or
> >slows down?
> >
> >T.Clinkscales
> >Technical Services
> >One World Technologies, Inc.
> >
> >
> >
> >
> >
> >
> >
> >
> >-----Original Message-----
> >From: [email protected] [mailto:[email protected]]
> >Sent: Tuesday, February 15, 2005 9:22 PM
> >To: [email protected]
> >Subject: Table Saw
> >
> >
> >Hello , I purchased a table saw from HD about 2 1/2 years ago when I
> thought
> >I would be interested in woodworking. My interest has grown and I
realized
> a
> >while ago that my table saw should be able to cut oak etc without burn
> marks
> >etc. After a close inspection I realized there was a wobble in the blade,
> so
> >I bougt a new blade, still a wobble. It would seem there is a problem
with
> >the arbor? I called customer service and was told to bring the saw to a
> >ridgid service center in my area. THe place is A&T tool in Huntington. I
> >dropped off my saw before Christmas as I was going away on vacation for 6
> >weeks. When I returned I called & they said it was all done. So I picked
it
> >up, asked what they found, but the guy who worked on it was off and all
> they
> >said was it was done. I came home plugged it in, still wobbles. I've now
> >found out they found nothing wrong with it. Can you imagine how hard it
was
> >for me to move my table saw to this place, then bring it home to find out
> >they did nothing? What am I to do? Anyone who knows anything about a
table
> >saw would know that for a blade to wobble means trouble. I'm really into
> >woodwork now & this is a problem. Can you please help me? I can't even
sell
> >it because I would feel bad about sending someone thru what I've been
thru.
>
>
>