Gooey wrote the following:
> On Jun 10, 2:33 pm, busbus <[email protected]> wrote:
>
>> I am in the market and this one seems intriguing. I have some clamps
>> and such from them and they are okay--I am not so sure about things
>> like air compressors.
>>
>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-ir...
>>
>
> bought oe of their pancake compressors - for a spare, light-duty work
> at a "second" shop. But would buy a Porter Cable (had for nearly ten
> years now doing lots of projects without issues) or similar for my
> first pancake compressor. I had a 30G Craftsman that has lasted twenty
> years ad still looks new and works just fine. Must admit that I am not
> a contractor, just a hobbyist.
>
> WARNING, HFT Heat Guns suck. Not only suck air in the rear and blow it
> out hot from the front as you might expect, but fail with very little
> use. On my second unit and it hasn't lasted six months! If you do get
> one, beware teh duty cycle. I suspect it's less than thirty seconds of
> continuous operating at High Heat setting.
>
I have a more minutes of operation than seconds. Still works.
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeroes after @
On Jun 11, 1:52=A0pm, Larry Jaques <[email protected]>
wrote:
> On Sat, 11 Jun 2011 09:44:59 -0700 (PDT), Angela Sekeris
>
> <[email protected]> wrote:
> >On Jun 11, 12:14=A0pm, Larry Jaques
>
> >> That was probably not more than 3bar, not the 10 we're talking with a
> >> compressor. =A0But the point is made.
>
> >I'm usually pretty well toasted after 10 bars.
>
> Hi, Angie. Have Toy take some nice pictures and email 'em, OK?
> Say, after 2 bars? =A0<wink>
>
Weiner style?
On Sunday, December 17, 2017 at 3:18:25 AM UTC-6, [email protected] wro=
te:
> I have used a <a href=3D"https://bestaircompressorstore.com/central-pneum=
atic-air-compressor-review/">central pneumatic 3-gallon air compressor</a> =
for three years for my little car. It is best portable and small but energy=
efficient. But I need a big model from my current models such as 8 or 10 g=
allons. Which will be suitable for my little car?
Don't know about the 10 gallon compressor. I think HF has two 8 gallon mo=
dels.
I've used the Model 69667 for a few years.... no problems with it. I just =
bought another for my Mother's home, so that I don't have to load/carry min=
e, there. Assembly is easy, 5 minutes. This model is on sale for $99 at=
my local HF.... might be on sale at your local store, also. I think a few=
years ago it cost $129.
It has to be plugged directly into the wall outlet, otherwise it won't run =
properly. If you want to use an extension cord, get one with 12 gauge or =
larger wire. 14 or 16 gauge wire is not sufficient. A 12 gauge wire cord=
needs to be 15' or less, in length, or the compressor won't work properly.=
I bought (Walmart - $25) an 8' 12 gauge wire surge protector power strip =
for Mom's compressor. Larger than 12 gauge wire will allow for using a lo=
nger than 15' cord, but I don't know a maximum length/range.
From what I've heard/learned, DIYers don't think/remember to drain the wate=
r from their tanks, hence, they end up having related issues with their "wo=
rk".... or have some sort of moisture issues for particular uses. Remembe=
r to drain the tank, often. There's a drain valve on the bottom of the ta=
nk. And use a catch basin, when you drain it.
Sonny
On 3/2/2014 12:05 PM, [email protected] wrote:
> I am wondering if you guys should just call the OP and see if he is still alive. Responding to posts that are nearly THREE years old aren't always productive use of your time.
>
> Of course, he could still be waiting to hear from you...
LMAO ...
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
On Jun 10, 2:33=A0pm, busbus <[email protected]> wrote:
> I am in the market and this one seems intriguing. =A0I have some clamps
> and such from them and they are okay--I am not so sure about things
> like air compressors.
>
> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-ir...
bought oe of their pancake compressors - for a spare, light-duty work
at a "second" shop. But would buy a Porter Cable (had for nearly ten
years now doing lots of projects without issues) or similar for my
first pancake compressor. I had a 30G Craftsman that has lasted twenty
years ad still looks new and works just fine. Must admit that I am not
a contractor, just a hobbyist.
WARNING, HFT Heat Guns suck. Not only suck air in the rear and blow it
out hot from the front as you might expect, but fail with very little
use. On my second unit and it hasn't lasted six months! If you do get
one, beware teh duty cycle. I suspect it's less than thirty seconds of
continuous operating at High Heat setting.
On 3/2/2014 12:05 PM, [email protected] wrote:
> I am wondering if you guys should just call the OP and see if he is still alive. Responding to posts that are nearly THREE years old aren't always productive use of your time.
>
> Of course, he could still be waiting to hear from you...
>
> Robert
>
And probably running out of breath. ;~)
[email protected] wrote:
> Working with Harbor
> Frieght tools is like sawing wood with a dull blade . . . You may
> eventually get the job done, but it won't look be easy, and the
> result may not be what your looking for. But then . . . are you
> building a birdhouse or a church?
Some are indeed like that, but others just are not. I don't buy many HF
tools with cords on them but I do own a couple. I use their 4 1/2 angle
grinders and consider them to be disposable. I keep two in my cabinet so
I'm never stranded if one bites the bullet. They work fine and take a lot
of abuse, but they do die. Then again, so did the Snap On grinder that
preceeded them. At least with these, I can replace them cheap, and keep on
working.
The other corded tool I have was a present - and it flat out works as it
should. It's a chain saw grinder. I generally file by hand and can both
keep and restore a chain with just a round file, with the best of them, but
there are times when it pays to reset the grind on a chain. I received the
tool as a gift, and I have to say that it works just as it should. I might
hit some chains once or twice a year (both my own and those of others), and
I defy anyone to tell the difference between what it produces, and what any
other more expensive unit would cost.
There are a lot of other things at HF that have served me well for years.
But then again - I do stay away from some categories of tools they sell.
--
-Mike-
[email protected]
Larry W wrote the following:
> In article <[email protected]>,
> CW <[email protected]> wrote:
> <...snipped...>
>
>> 150 PSI Chinese bomb. Considering the quality level of HF merchandise
>> (everywhere from not bad to total crap) I wouldn't trust them with my life
>> and that's what you are doing using their air compressor. Odds are though
>> you won't get the one welded together by the pissed off slave labor. Feeling
>> lucky?
>>
>>
>>
>
> Yes, it would be _so_much_better_ to buy one from Campbell Hausfield,
> Husky, or some other name-brand- ALSO made in China!
>
I replaced my CH compressor which died, with a HF compressor. I figured
the cheaper price offsets the assumed longevity of the more expensive
compressors.
My CH compressor was only used for topping off tires and pool equipment.
>
>
> To the OP:
>
> I can't speak for that particular compressor but I have used one of their
> smaller 8 gal horizontal tank models for weekend warrior use for about
> 6 years now without trouble.
>
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeroes after @
Bill wrote the following:
> -MIKE- wrote:
>> On 6/10/11 3:21 PM, CW wrote:
>>> "busbus"<[email protected]> wrote in message
>>> news:27a2f258-121a-4097-b274-4b82018ccf6f@w36g2000vbi.googlegroups.com...
>>>
>>>> I am in the market and this one seems intriguing. I have some clamps
>>>> and such from them and they are okay--I am not so sure about things
>>>> like air compressors.
>>>>
>>>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>>>>
>>>>
>>>
>>> 150 PSI Chinese bomb. Considering the quality level of HF merchandise
>>> (everywhere from not bad to total crap) I wouldn't trust them with my
>>> life
>>> and that's what you are doing using their air compressor. Odds are
>>> though
>>> you won't get the one welded together by the pissed off slave labor.
>>> Feeling
>>> lucky?
>>>
>>
>> So you're one of those guys who thinks an air talk can explode like a
>> bomb, huh?
>>
>
> I assume it's got a safety valve of some sort. What's the skinny?
>
> Bill
Chinese stuff is presumed to be crap, like Japanese stuff was in the 50s.
Does he know that Japanese products, like US products, have been
outsourced to China for years?
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeroes after @
On 06/10/2011 07:39 PM, k-nuttle wrote:
> On 6/10/2011 7:57 PM, RonB wrote:
>> On Jun 10, 1:33 pm, busbus<[email protected]> wrote:
>>> I am in the market and this one seems intriguing. I have some clamps
>>> and such from them and they are okay--I am not so sure about things
>>> like air compressors.
>>>
>>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-ir...
>>
>> I am not a big HF fan, but I have had pretty good luck with some of
>> their stuff. I have had one of their $99 special mortise machines for
>> several years. The hold down hardware sucks but the machine has
>> plenty of power and cuts square holes and slots with help of clamps.
>> I have some of their smaller tools that work well. 18 Gage nailer
>> won't wear out -- $20.
>>
>> No air compressor experience.
>>
>> Ron
>
> I have one of their small tire inflators, It normally went for about
> $29, but was on special for $15. I have been using it for several years
> now and am completely happy with it. Its volume is good and while I use
> it principally for my JD garden tractor, I have used it on my van which
> has 40psi in the tires.
>
> I would recommend it to anyone who asked.
>
> While I have bought other things at HF and never been disappointed, this
> is the only electrical tool I have.
I have this one for airing up tires on the 54th wheel and occasional
brad nailer use when out of range of the "big 240V" compressor. On sale
and with a 20% off coupon, got it for under $40.
<http://www.harborfreight.com/3-gallon-100-psi-oilless-pancake-air-compressor-95275.html>
Noisy, but works great.
On 06/10/2011 07:53 PM, Doug Winterburn wrote:
> On 06/10/2011 07:39 PM, k-nuttle wrote:
>> On 6/10/2011 7:57 PM, RonB wrote:
>>> On Jun 10, 1:33 pm, busbus<[email protected]> wrote:
>>>> I am in the market and this one seems intriguing. I have some clamps
>>>> and such from them and they are okay--I am not so sure about things
>>>> like air compressors.
>>>>
>>>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-ir...
>>>>
>>>
>>> I am not a big HF fan, but I have had pretty good luck with some of
>>> their stuff. I have had one of their $99 special mortise machines for
>>> several years. The hold down hardware sucks but the machine has
>>> plenty of power and cuts square holes and slots with help of clamps.
>>> I have some of their smaller tools that work well. 18 Gage nailer
>>> won't wear out -- $20.
>>>
>>> No air compressor experience.
>>>
>>> Ron
>>
>> I have one of their small tire inflators, It normally went for about
>> $29, but was on special for $15. I have been using it for several years
>> now and am completely happy with it. Its volume is good and while I use
>> it principally for my JD garden tractor, I have used it on my van which
>> has 40psi in the tires.
>>
>> I would recommend it to anyone who asked.
>>
>> While I have bought other things at HF and never been disappointed, this
>> is the only electrical tool I have.
>
> I have this one for airing up tires on the 54th wheel and occasional
> brad nailer use when out of range of the "big 240V" compressor. On sale
> and with a 20% off coupon, got it for under $40.
>
> <http://www.harborfreight.com/3-gallon-100-psi-oilless-pancake-air-compressor-95275.html>
>
>
> Noisy, but works great.
That'd be 5th wheel...
"busbus" wrote:
> I am in the market and this one seems intriguing. I have some clamps
> and such from them and they are okay--I am not so sure about things
> like air compressors.
> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
-------------------------------------
Consider it as a throw away.
Anything beyond a year and you are ahead of the game.
Lew
On Sat, 01 Mar 2014 13:11:04 -0500, woodchucker wrote:
> On 3/1/2014 12:57 PM, [email protected] wrote:
>> On Friday, June 10, 2011 11:33:40 AM UTC-7, busbus wrote:
>>> I am in the market and this one seems intriguing. I have some clamps
>>> and such from them and they are okay--I am not so sure about things
>>> like air compressors.
>>>
>>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-
iron-vertical-air-compressor-67847.html
>>
>> I bought this air compressor on the Richland washington store. It had a
>> special sign on it for $100.00 ! I bit and bought it. I plugged it
>> in and tried it. It would not work. I tried and tried and finally it
>> came on. Then it froze up. That has been a year ago. I dug out my
>> receipt to take it back. BUT, the receipt said "AS IS "! Nothing
>> about that before I bought it. Not a thing on the sign outside. Am
>> thinking Harbor Freight is not on the up and up ?
>>
> Sounds like it was a return and the as is was intended on getting rid of
> it, maybe for parts.
I bought a similar HF compressor years and years ago. When it arrived the
starting capacitor had become disconnected in shipping. Fixed it and the
compressor has worked fine every since.
Also, does it has oil?
[email protected] wrote:
>> I am wondering if you guys should just call the OP and see if he is
>> still alive. Responding to posts that are nearly THREE years old
>> aren't always productive use of your time.
>>
>> Of course, he could still be waiting to hear from you...
-----------------------------------------------------------
"Mike Marlow" wrote:
> Why do people get so damned anal about this stuff? Most of us - or
> maybe, some of us don't look at headers to see date stamps. Was it
> really such a bother to you that some of us replied?
-----------------------------------------------------------
Picked up a case of upstate New York cabin fever Bunky?
Only a couple of more months.
Lew
On Sat, 11 Jun 2011 09:44:59 -0700 (PDT), Angela Sekeris
<[email protected]> wrote:
>On Jun 11, 12:14Â pm, Larry Jaques
>>
>> That was probably not more than 3bar, not the 10 we're talking with a
>> compressor. Â But the point is made.
>
>I'm usually pretty well toasted after 10 bars.
Hi, Angie. Have Toy take some nice pictures and email 'em, OK?
Say, after 2 bars? <wink>
--
The ultimate result of shielding men from the
effects of folly is to fill the world with fools.
--Herbert Spencer
On Jun 10, 1:33=A0pm, busbus <[email protected]> wrote:
> I am in the market and this one seems intriguing. =A0I have some clamps
> and such from them and they are okay--I am not so sure about things
> like air compressors.
>
> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-ir...
I am not a big HF fan, but I have had pretty good luck with some of
their stuff. I have had one of their $99 special mortise machines for
several years. The hold down hardware sucks but the machine has
plenty of power and cuts square holes and slots with help of clamps.
I have some of their smaller tools that work well. 18 Gage nailer
won't wear out -- $20.
No air compressor experience.
Ron
On Friday, June 10, 2011 11:33:40 AM UTC-7, busbus wrote:
> I am in the market and this one seems intriguing. I have some clamps
> and such from them and they are okay--I am not so sure about things
> like air compressors.
>=20
> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-v=
ertical-air-compressor-67847.html
I bought this air compressor on the Richland washington store. It had a spe=
cial sign on it for $100.00 ! I bit and bought it. I plugged it in and t=
ried it. It would not work. I tried and tried and finally it came on. The=
n it froze up. That has been a year ago. I dug out my receipt to take it b=
ack. BUT, the receipt said "AS IS "! Nothing about that before I bought =
it. Not a thing on the sign outside. Am thinking Harbor Freight is not on t=
he up and up ?
On Jun 11, 12:44=A0pm, Angela Sekeris <[email protected]> wrote:
> On Jun 11, 12:14=A0pm, Larry Jaques
>
>
>
> > That was probably not more than 3bar, not the 10 we're talking with a
> > compressor. =A0But the point is made.
>
> I'm usually pretty well toasted after 10 bars.
I HAVE TO learn to check and see who the hell used this laptop
last......
busbus wrote:
> I am in the market and this one seems intriguing. I have some clamps
> and such from them and they are okay--I am not so sure about things
> like air compressors.
>
> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
For a broader view, check out Harbor Freight Reviews (not affiliated with
the company).
http://hfreviews.com/
For example, their pancake compressor got a 4-out-of-5 review.
On the other hand, if you buy it and it doesn't meet your expectations, take
it back for a full refund. HF has a VERY liberal returns policy.
Doug Winterburn wrote:
<snip>
>> I have this one for airing up tires on the 54th wheel and occasional
>> brad nailer use when out of range of the "big 240V" compressor. On sale
>> and with a 20% off coupon, got it for under $40.
>>
>> <http://www.harborfreight.com/3-gallon-100-psi-oilless-pancake-air-compressor-95275.html>
>>
>>
>> Noisy, but works great.
>
> That'd be 5th wheel...
Would you believe my old brain actually read that as "5th wheel" the
first time? I had to go back to see what you were correcting.
--
Gerald Ross
Cochran, GA
Tried to play my shoehorn... all I got
was footnotes!
Harbor Freight specs all thier tools to meet minimum requirements. In the
case of a clamp, screw driver, hand wrench or other item of that type,
disposable is ok if your on a budget. I have my share of junk tools for
purposes that are "one time" or "Infrequent" use, and they are fine for
that. When it comes to a big ticket tool like a compressor, table saw, drill
press or the like . . . I always save up and go for name brand. I've never
been sorry that I spent the extra money for a top grade tool, or at least
the ones that matter. I ended up with a Rigid compressor, only for the fact
that I plan to use it very infrequently, but still wanted a name brand tool
to ensure a safety margin and some reliability. I don't even think of Harbor
Frieght when I am considering a serious purchase. Thier stuff is strictly
for one time, very infrequent, or when it doesn't matter if the tool works
properly. I did purchase one of the Mini Machine lathes they sell . . . And
it operates just like the piece of junk I paid for . . . But it did manage
to do the job it was bought for, even if it took twice as long to get the
accuracy that a good machine would have achieved with very little effort.
Working with Harbor Frieght tools is like sawing wood with a dull blade . .
. You may eventually get the job done, but it won't look be easy, and the
result may not be what your looking for. But then . . . are you building a
birdhouse or a church?
--
Offered in the spirit of friendship and respect :)
busbus wrote the following:
> I am in the market and this one seems intriguing. I have some clamps
> and such from them and they are okay--I am not so sure about things
> like air compressors.
>
> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>
I have no experience with that large one, but the smaller one works.
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeroes after @
[email protected] wrote:
> On Friday, June 10, 2011 11:33:40 AM UTC-7, busbus wrote:
>> I am in the market and this one seems intriguing. I have some clamps
>> and such from them and they are okay--I am not so sure about things
>> like air compressors.
>>
>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>
> I bought this air compressor on the Richland washington store. It had a special sign on it for $100.00 ! I bit and bought it. I plugged it in and tried it. It would not work. I tried and tried and finally it came on. Then it froze up. That has been a year ago. I dug out my receipt to take it back. BUT, the receipt said "AS IS "! Nothing about that before I bought it. Not a thing on the sign outside. Am thinking Harbor Freight is not on the up and up ?
It looks like a direct drive (no belt). Those tend to be very noisy.
I had a similar one and it later needed a part. It took 2 months to
get it as it had to come from China. Sold it and bought a used belt
driven one and have not had any problems with that one.
--
GW Ross
Every vision has an equal and
opposite revision.
In article <[email protected]>,
<[email protected]> wrote:
>On Fri, 10 Jun 2011 11:33:40 -0700 (PDT), busbus <[email protected]>
>wrote:
>
>You should ask on the Welding Web forum http://weldingweb.com/ where
>they have branches for "HF tools that don't suck" and "HF tools that
>suck". There's probably someone there who has used this compressor.
Rumor mill says that HF vacuum cleaners are one of the few pieces of
power equipment on the _first_ list. *grin*
On 3/1/2014 12:57 PM, [email protected] wrote:
> On Friday, June 10, 2011 11:33:40 AM UTC-7, busbus wrote:
>> I am in the market and this one seems intriguing. I have some clamps
>> and such from them and they are okay--I am not so sure about things
>> like air compressors.
>>
>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>
> I bought this air compressor on the Richland washington store. It had a special sign on it for $100.00 ! I bit and bought it. I plugged it in and tried it. It would not work. I tried and tried and finally it came on. Then it froze up. That has been a year ago. I dug out my receipt to take it back. BUT, the receipt said "AS IS "! Nothing about that before I bought it. Not a thing on the sign outside. Am thinking Harbor Freight is not on the up and up ?
>
Take the motor off and see if it runs for 20 minutes w/o a load, the
motor might be the problem.
If not, then find out what is going on in the compressor section.
Take that apart might be a bad ring.. they use rubberized, (silicone o,
teflon, or others for rings and that's how they stay oil free. Maybe the
ring broke and is binding.
--
Jeff
On 3/1/2014 12:57 PM, [email protected] wrote:
> On Friday, June 10, 2011 11:33:40 AM UTC-7, busbus wrote:
>> I am in the market and this one seems intriguing. I have some clamps
>> and such from them and they are okay--I am not so sure about things
>> like air compressors.
>>
>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>
> I bought this air compressor on the Richland washington store. It had a special sign on it for $100.00 ! I bit and bought it. I plugged it in and tried it. It would not work. I tried and tried and finally it came on. Then it froze up. That has been a year ago. I dug out my receipt to take it back. BUT, the receipt said "AS IS "! Nothing about that before I bought it. Not a thing on the sign outside. Am thinking Harbor Freight is not on the up and up ?
>
Sounds like it was a return and the as is was intended on getting rid of
it, maybe for parts.
--
Jeff
On 3/3/2014 4:23 AM, Mike Marlow wrote:
> Lew Hodgett wrote:
>> [email protected] wrote:
>>
>>>> I am wondering if you guys should just call the OP and see if he is
>>>> still alive. Responding to posts that are nearly THREE years old
>>>> aren't always productive use of your time.
>>>>
>>>> Of course, he could still be waiting to hear from you...
>> -----------------------------------------------------------
>> "Mike Marlow" wrote:
>>
>>> Why do people get so damned anal about this stuff? Most of us - or
>>> maybe, some of us don't look at headers to see date stamps. Was it
>>> really such a bother to you that some of us replied?
>> -----------------------------------------------------------
>> Picked up a case of upstate New York cabin fever Bunky?
>>
>> Only a couple of more months.
>>
>
> Funny! Almost so true too! I will tell you that this is probably the first
> year ever that I just can't wait for winter to be over. Tired of the cold,
> had enough snow, just want to be able to pee out on my front lawn again...
>
Had an orange tabby cat named Bill (named after the Breathed character).
He absolutely loved to get out onto the deck with a couple feet of
snow on it. He would dig tunnels, make snow angels, and before he came
in, would have a poop and a pee. Wonderful. The stuff would freeze and
as long as I got to it before the big melt, it didn't stink or stain.
Miss that cat.
mahalo,
jo4hn
On 3/3/2014 7:23 AM, Mike Marlow wrote:
> Lew Hodgett wrote:
>> [email protected] wrote:
>>
>>>> I am wondering if you guys should just call the OP and see if he is
>>>> still alive. Responding to posts that are nearly THREE years old
>>>> aren't always productive use of your time.
>>>>
>>>> Of course, he could still be waiting to hear from you...
>> -----------------------------------------------------------
>> "Mike Marlow" wrote:
>>
>>> Why do people get so damned anal about this stuff? Most of us - or
>>> maybe, some of us don't look at headers to see date stamps. Was it
>>> really such a bother to you that some of us replied?
>> -----------------------------------------------------------
>> Picked up a case of upstate New York cabin fever Bunky?
>>
>> Only a couple of more months.
>>
>
> Funny! Almost so true too! I will tell you that this is probably the first
> year ever that I just can't wait for winter to be over. Tired of the cold,
> had enough snow, just want to be able to pee out on my front lawn again...
>
woof woof
--
Jeff
I have used a <a href=3D"https://bestaircompressorstore.com/central-pneumat=
ic-air-compressor-review/">central pneumatic 3-gallon air compressor</a> fo=
r three years for my little car. It is best portable and small but energy e=
fficient. But I need a big model from my current models such as 8 or 10 gal=
lons. Which will be suitable for my little car?
On Jun 11, 1:45=A0am, Larry Jaques
> wot?
Problem is, that when people try to imagine what an air tank failure
would look like, their imaginations become filled with fuel/grenade/
gasoline/actionmoviebullshit type explosions.
The escape of normal (135psig?) air pressure out of a failed metal
tank will not be accompanied by a full perimeter failure releasing a
rather benign quantity of stored energy. It will release in a fart-
like measured amount.
It will be a big howling puff, but no bang, and any shit flying will
be because of the startle factor, not due to released energy.
For giggles, my mechanic and his friends hooked up a motorcycle inner
tube to a 165psig line in a garage and just let it get bigger and
bigger. So big in fact that a huge hernia appeared which became almost
see-through thin. When it failed, it made a bang, much louder than a
balloon, but not mortar launch grade. The flying remnants did knock
over a beer, much to the chagrin of one the participants. Yes alcohol
was involved. No blown-out windows. The hose-end with the metal nipple
did fly around for quite a while till the main valve was shut off.
On Sat, 1 Mar 2014 09:57:15 -0800 (PST), [email protected]
wrote:
>On Friday, June 10, 2011 11:33:40 AM UTC-7, busbus wrote:
>> I am in the market and this one seems intriguing. I have some clamps
>> and such from them and they are okay--I am not so sure about things
>> like air compressors.
>>
>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>
>I bought this air compressor on the Richland washington store. It had a special sign on it for $100.00 ! I bit and bought it. I plugged it in and tried it. It would not work. I tried and tried and finally it came on. Then it froze up. That has been a year ago. I dug out my receipt to take it back. BUT, the receipt said "AS IS "! Nothing about that before I bought it. Not a thing on the sign outside. Am thinking Harbor Freight is not on the up and up ?
I'm thinking you were asleep at the switch. When the price sounds
too good to be true, it usually is. Deep discounts from their already
"discount" prices are almost always "as is".
On Fri, 10 Jun 2011 15:18:27 -0400, [email protected] wrote:
>On Fri, 10 Jun 2011 11:33:40 -0700 (PDT), busbus <[email protected]>
>wrote:
>
>>I am in the market and this one seems intriguing. I have some clamps
>>and such from them and they are okay--I am not so sure about things
>>like air compressors.
>>
>>http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>
>I have one of their smaller compressors and it works fine for my
>needs.
I have one of their 47065 (4.65 peak horsies on 120v <giggle>, 21
gallon vertical) compressors and it works fine. 2+ years old, not used
a whole lot, doesn't leak much. They're loud but serviceable
beasties.
If I had it to do over, I might buy a pump, motor, and tank
separately, for improved CFM.
This looks like the same comp, rebadged with TALL AD LETTERING.
Same price/capacity.
WOW, HF now has a gasoline powered compressor for $599.
http://goo.gl/Tu8u2 Has anyone used one yet?
--
The ultimate result of shielding men from the
effects of folly is to fill the world with fools.
--Herbert Spencer
On Jun 16, 1:32=A0am, "Mike Marlow" <[email protected]>
wrote:
> [email protected] wrote:
> > Working with Harbor
> > Frieght tools is like sawing wood with a dull blade . . . You may
> > eventually get the job done, but it won't look be easy, and the
> > result may not be what your looking for. But then . . . are you
> > building a birdhouse or a church?
>
> Some are indeed like that, but others just are not.
I agree: some are worth it and some are not. The thing is, I
physically looked at a bunch of other pancake compressors and felt
that this one from HF would probably serve ME best. The darn four-
gallon tank is filled with air and ready to go in a little over 30
seconds. A buddy of mine has a smallish Porter Cable and he says it
takes him about four minutes load fill a three-gallon tank. Of
course, his cost about $60 at a big box store, so you know it's not
anything special.
I am an infrequent user, to say the least. I do have plans on putting
on a new roof but, other than that, I don't plan on using it every day
or even every week...maybe most weeks but not every week. And, at
$67, it is also a disposable tool. I know it won't last forever but I
am hoping it lasts long enough.
If my ivelihood or my life depended on it, I don't think I would have
bought it. But for what I want/need, this thing seems like it will be
okay.
On Jun 10, 10:53=A0pm, Doug Winterburn <[email protected]> wrote:
> On 06/10/2011 07:39 PM, k-nuttle wrote:
>
>
>
>
>
>
>
>
>
> > On 6/10/2011 7:57 PM, RonB wrote:
> I have this one for airing up tires on the 54th wheel and occasional
> brad nailer use when out of range of the "big 240V" compressor. =A0On sal=
e
> and with a 20% off coupon, got it for under $40.
>
> <http://www.harborfreight.com/3-gallon-100-psi-oilless-pancake-air-com...=
>
>
> Noisy, but works great.
I ended up getting one of these:
http://www.harborfreight.com/merchandising-promotions/merchandising/parking=
-lot-sale-6-11-html/2-hp-4-gallon-115-psi-pancake-compressor-95499.html
I got it for $60, so if it lasts a year or two, I have to be ahead of
the game. I will be using it to inflate tires and basketballs and
such plus a new roof. If it lasts thru the roof, anyways, I will have
gotten my money's worth. It is a noisy little bugger but I can deal
with it for 60 bucks.
I know it is a Chinese throwaway tool and, yes, it will certainly
develop a leak sooner rather than later but I have no fears that it
will explode. There is a relief valve and it works just peachy. Why
are people so afraid of something that will (statistically) never
happen? I know the quality is not top notch but if these things
failed and actually BLEW UP, then I don't think HF would still be
around. Nor would Crapsman or Campbell-Hausfeld or just about any
company!
busbus
On 2011-06-11 23:15:04 -0400, busbus <[email protected]> said:
> Why
> are people so afraid of something that will (statistically) never
> happen?
You mean, like, why the hell do we let TSA get away with their
nonsensical empire-building?
On 2011-06-13 11:26:06 -0400, Larry Jaques
<[email protected]> said:
> I think you misspelled "The Government", Steve. And Homeland Security
> owns the TSA.
Ok, maybe I was giving TSA too much credit.
On Mon, 13 Jun 2011 23:50:39 -0400, Steve
<[email protected]> wrote:
>On 2011-06-13 11:26:06 -0400, Larry Jaques
><[email protected]> said:
>
>> I think you misspelled "The Government", Steve. And Homeland Security
>> owns the TSA.
>
>Ok, maybe I was giving TSA too much credit.
Some people think giving them _any_ credit would be too much.
--
To know the road ahead, ask those coming back.
-- Chinese Proverb
On Sun, 12 Jun 2011 18:55:24 -0400, Steve
<[email protected]> wrote:
>On 2011-06-11 23:15:04 -0400, busbus <[email protected]> said:
>
>> Why
>> are people so afraid of something that will (statistically) never
>> happen?
>
>You mean, like, why the hell do we let TSA get away with their
>nonsensical empire-building? ^^^
I think you misspelled "The Government", Steve. And Homeland Security
owns the TSA.
--
The ultimate result of shielding men from the
effects of folly is to fill the world with fools.
--Herbert Spencer
On Fri, 10 Jun 2011 11:33:40 -0700 (PDT), busbus <[email protected]>
wrote:
>I am in the market and this one seems intriguing. I have some clamps
>and such from them and they are okay--I am not so sure about things
>like air compressors.
>
>http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
I have one of their smaller compressors and it works fine for my
needs.
You should ask on the Welding Web forum http://weldingweb.com/ where
they have branches for "HF tools that don't suck" and "HF tools that
suck". There's probably someone there who has used this compressor.
John
On Sat, 11 Jun 2011 08:33:52 -0700 (PDT), Robatoy
<[email protected]> wrote:
>On Jun 11, 1:45Â am, Larry Jaques
>> wot?
NOW yer snippin'.
>Problem is, that when people try to imagine what an air tank failure
>would look like, their imaginations become filled with fuel/grenade/
>gasoline/actionmoviebullshit type explosions.
Like watching the guy plant a single ounce of C4 with a detanator and
then seeing (and hearing) seventeen discrete charges blow up the
house, all from 3 angles? Yeah, that's them.
>The escape of normal (135psig?) air pressure out of a failed metal
>tank will not be accompanied by a full perimeter failure releasing a
>rather benign quantity of stored energy. It will release in a fart-
>like measured amount.
>It will be a big howling puff, but no bang, and any shit flying will
>be because of the startle factor, not due to released energy.
Wow, whose farts make your ears pop? No...I don't want to know.
Maybe I _won't_ visit Canada.
>For giggles, my mechanic and his friends hooked up a motorcycle inner
>tube to a 165psig line in a garage and just let it get bigger and
>bigger. So big in fact that a huge hernia appeared which became almost
>see-through thin. When it failed, it made a bang, much louder than a
>balloon, but not mortar launch grade. The flying remnants did knock
>over a beer, much to the chagrin of one the participants. Yes alcohol
>was involved. No blown-out windows. The hose-end with the metal nipple
>did fly around for quite a while till the main valve was shut off.
That was probably not more than 3bar, not the 10 we're talking with a
compressor. But the point is made.
--
The ultimate result of shielding men from the
effects of folly is to fill the world with fools.
--Herbert Spencer
On Mon, 13 Jun 2011 15:53:13 -0700 (PDT), Robatoy
<[email protected]> wrote:
>On Jun 12, 10:57Â pm, Larry Jaques <[email protected]>
>wrote:
>> On Sun, 12 Jun 2011 11:36:27 -0700 (PDT), Robatoy
>>
>> <[email protected]> wrote:
>> >On Jun 12, 12:04Â am, Larry Jaques <[email protected]>
>> >wrote:
>> >> I was thinking Penthouse style, unless you like much older women.
>>
>> >There is an 18 year difference between Ang and I, so 'older' isn't my
>> >bag.
>>
>> "Ang and me", and where the -hell- are thos pics? Â <g>
>>
>Ang and I need to go through and select which pictures are
>publishable.
I want copies of those which AREN'T, got it? <evil grinne>
--
You are today where your thoughts have brought you;
you will be tomorrow where your thoughts take you.
-- James Lane Allen
In article <[email protected]>,
CW <[email protected]> wrote:
<...snipped...>
>150 PSI Chinese bomb. Considering the quality level of HF merchandise
>(everywhere from not bad to total crap) I wouldn't trust them with my life
>and that's what you are doing using their air compressor. Odds are though
>you won't get the one welded together by the pissed off slave labor. Feeling
>lucky?
>
>
Yes, it would be _so_much_better_ to buy one from Campbell Hausfield,
Husky, or some other name-brand- ALSO made in China!
To the OP:
I can't speak for that particular compressor but I have used one of their
smaller 8 gal horizontal tank models for weekend warrior use for about
6 years now without trouble.
--
Make it as simple as possible, but not simpler. (Albert Einstein)
Larry Wasserman - Baltimore Maryland - lwasserm(a)sdf. lonestar. org
On 6/10/11 3:21 PM, CW wrote:
> "busbus"<[email protected]> wrote in message
> news:27a2f258-121a-4097-b274-4b82018ccf6f@w36g2000vbi.googlegroups.com...
>> I am in the market and this one seems intriguing. I have some clamps
>> and such from them and they are okay--I am not so sure about things
>> like air compressors.
>>
>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>
> 150 PSI Chinese bomb. Considering the quality level of HF merchandise
> (everywhere from not bad to total crap) I wouldn't trust them with my life
> and that's what you are doing using their air compressor. Odds are though
> you won't get the one welded together by the pissed off slave labor. Feeling
> lucky?
>
So you're one of those guys who thinks an air talk can explode like a
bomb, huh?
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
-MIKE- wrote:
> On 6/10/11 3:21 PM, CW wrote:
>> "busbus"<[email protected]> wrote in message
>> news:27a2f258-121a-4097-b274-4b82018ccf6f@w36g2000vbi.googlegroups.com...
>>> I am in the market and this one seems intriguing. I have some clamps
>>> and such from them and they are okay--I am not so sure about things
>>> like air compressors.
>>>
>>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>>>
>>
>> 150 PSI Chinese bomb. Considering the quality level of HF merchandise
>> (everywhere from not bad to total crap) I wouldn't trust them with my
>> life
>> and that's what you are doing using their air compressor. Odds are though
>> you won't get the one welded together by the pissed off slave labor.
>> Feeling
>> lucky?
>>
>
> So you're one of those guys who thinks an air talk can explode like a
> bomb, huh?
>
I assume it's got a safety valve of some sort. What's the skinny?
Bill
>
On 6/10/2011 7:57 PM, RonB wrote:
> On Jun 10, 1:33 pm, busbus<[email protected]> wrote:
>> I am in the market and this one seems intriguing. I have some clamps
>> and such from them and they are okay--I am not so sure about things
>> like air compressors.
>>
>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-ir...
>
> I am not a big HF fan, but I have had pretty good luck with some of
> their stuff. I have had one of their $99 special mortise machines for
> several years. The hold down hardware sucks but the machine has
> plenty of power and cuts square holes and slots with help of clamps.
> I have some of their smaller tools that work well. 18 Gage nailer
> won't wear out -- $20.
>
> No air compressor experience.
>
> Ron
I have one of their small tire inflators, It normally went for about
$29, but was on special for $15. I have been using it for several years
now and am completely happy with it. Its volume is good and while I use
it principally for my JD garden tractor, I have used it on my van which
has 40psi in the tires.
I would recommend it to anyone who asked.
While I have bought other things at HF and never been disappointed, this
is the only electrical tool I have.
"busbus" wrote in message
news:27a2f258-121a-4097-b274-4b82018ccf6f@w36g2000vbi.googlegroups.com...
I am in the market and this one seems intriguing. I have some clamps
and such from them and they are okay--I am not so sure about things
like air compressors.
http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
==========
I am thinking this unit looks exactly like the unit I purchased a few years
ago under the Campbell and Hausfeld brand name.
The units works well but the noise will drive you out of house and home!! I
have the unit in my garage and if it kicks in while in the garage you would
jump out of your skin. I am so glad I wear earmuffs while operating my mitre
saw when it kicks in or I would probably have cut my hand off by now. I have
thought of boxing it in when I move it to a more permanent place and sound
insulate the monster. I know my EU2000i Honda Generator will not start it,
run it yes but not start it again...big electric surge!
Knowing the noise factor I would look for another unit. Some of the newer
pancake units are half the noise and quarter the size.
--
Eric
On 6/11/11 12:45 AM, Larry Jaques wrote:
> On Fri, 10 Jun 2011 19:32:17 -0400, Bill<[email protected]> wrote:
>
>> -MIKE- wrote:
>>> On 6/10/11 3:21 PM, CW wrote:
>>>> "busbus"<[email protected]> wrote in message
>>>> news:27a2f258-121a-4097-b274-4b82018ccf6f@w36g2000vbi.googlegroups.com...
>>>>> I am in the market and this one seems intriguing. I have some clamps
>>>>> and such from them and they are okay--I am not so sure about things
>>>>> like air compressors.
>>>>>
>>>>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>>>>>
>>>>
>>>> 150 PSI Chinese bomb. Considering the quality level of HF merchandise
>>>> (everywhere from not bad to total crap) I wouldn't trust them with my
>>>> life
>>>> and that's what you are doing using their air compressor. Odds are though
>>>> you won't get the one welded together by the pissed off slave labor.
>>>> Feeling
>>>> lucky?
>>>>
>>>
>>> So you're one of those guys who thinks an air talk can explode like a
>>> bomb, huh?
>>>
>>
>> I assume it's got a safety valve of some sort. What's the skinny?
>
> I haven't checked the stats, but my SWAG is that 98.99% of tanks
> develop pinhole leaks which expand, )1% blow at the seams sans
> shrapnel, and the other 0.01% have pressure relief valves stick (how
> much overpressure can a cheap pump put out, anyway?) and they actually
> explode, hurting someone. Here's the nastiest one I could find in ten
> minutes.<giggle> http://goo.gl/I5ab8
>
You're using paintball guns for your air tools?
> Seam ruptures on a 21 gallon tank put (15psia empty, 150psi full) 210
> gallons of air into the shop in a short amount of time, blowing out
> the windows and making the ears smart a bit, wot?
>
No. Weakest link in the chain (hole) breaks first, not the whole chain.
The hole blows out the pressure. Worst that can happen is is shoots
across the room like a rocket, not an explosion.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
"Larry Jaques" <[email protected]> wrote in message
news:[email protected]...
> On Fri, 10 Jun 2011 19:32:17 -0400, Bill <[email protected]> wrote:
>
>>-MIKE- wrote:
>>> On 6/10/11 3:21 PM, CW wrote:
>>>> "busbus"<[email protected]> wrote in message
>>>> news:27a2f258-121a-4097-b274-4b82018ccf6f@w36g2000vbi.googlegroups.com...
>>>>> I am in the market and this one seems intriguing. I have some clamps
>>>>> and such from them and they are okay--I am not so sure about things
>>>>> like air compressors.
>>>>>
>>>>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>>>>>
>>>>
>>>> 150 PSI Chinese bomb. Considering the quality level of HF merchandise
>>>> (everywhere from not bad to total crap) I wouldn't trust them with my
>>>> life
>>>> and that's what you are doing using their air compressor. Odds are
>>>> though
>>>> you won't get the one welded together by the pissed off slave labor.
>>>> Feeling
>>>> lucky?
>>>>
>>>
>>> So you're one of those guys who thinks an air talk can explode like a
>>> bomb, huh?
>>>
>>
>>I assume it's got a safety valve of some sort. What's the skinny?
>
> I haven't checked the stats, but my SWAG is that 98.99% of tanks
> develop pinhole leaks which expand, )1% blow at the seams sans
> shrapnel, and the other 0.01% have pressure relief valves stick (how
> much overpressure can a cheap pump put out, anyway?) and they actually
> explode, hurting someone. Here's the nastiest one I could find in ten
> minutes. <giggle> http://goo.gl/I5ab8
>
> Seam ruptures on a 21 gallon tank put (15psia empty, 150psi full) 210
> gallons of air into the shop in a short amount of time, blowing out
> the windows and making the ears smart a bit, wot?
>
Used to do mechanical QA on tubing. We pumped it full of liquid until it
burst. One end was fixed and the other plugged and free and the whole mess
was in a shrapnel proof cabinet. Goal was to get the burst pressure which,
for the stuff we were testing, was in the neighborhood of 35,000 psi. First
time I did one I got to 60,000 psi and pinholed. Let it sit for a while
dropping, then it stopped around 50,000. Couldn't find the pressure release
valve and hunted down the boss. Deal was you took an asbestos glove and
wrench, reached in the cabinet and eased off the fixture until the fluid
escaped at the fixed end. Told him I didn't sign up for that ...
On 6/11/11 10:15 PM, busbus wrote:
> Why are people so afraid of something that will (statistically) never
> happen?
>
> busbus
Statistically or physically.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On Sat, 1 Mar 2014 09:57:15 -0800 (PST), [email protected]
wrote:
>On Friday, June 10, 2011 11:33:40 AM UTC-7, busbus wrote:
>> I am in the market and this one seems intriguing. I have some clamps
>> and such from them and they are okay--I am not so sure about things
>> like air compressors.
>>
>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>
>I bought this air compressor on the Richland washington store. It had a special sign on it for $100.00 ! I bit and bought it. I plugged it in and tried it. It would not work. I tried and tried and finally it came on. Then it froze up. That has been a year ago. I dug out my receipt to take it back. BUT, the receipt said "AS IS "! Nothing about that before I bought it. Not a thing on the sign outside. Am thinking Harbor Freight is not on the up and up ?
Was there a sign stating that it was as-is? If not, I'd take it back
and argue the point. HF is particularly good about returns. If they
don't take it back without questions, buck it up the chain.
On Sat, 11 Jun 2011 09:52:47 -0700 (PDT), Robatoy
<[email protected]> wrote:
>On Jun 11, 12:44Â pm, Angela Sekeris <[email protected]> wrote:
>> On Jun 11, 12:14Â pm, Larry Jaques
>>
>>
>>
>> > That was probably not more than 3bar, not the 10 we're talking with a
>> > compressor. Â But the point is made.
>>
>> I'm usually pretty well toasted after 10 bars.
>
>I HAVE TO learn to check and see who the hell used this laptop
>last......
Wait until you see my last reply, suckah!
<gd&r>
P.S: ...but if she's up for it... ;)
--
The ultimate result of shielding men from the
effects of folly is to fill the world with fools.
--Herbert Spencer
[email protected] wrote:
> I am wondering if you guys should just call the OP and see if he is
> still alive. Responding to posts that are nearly THREE years old
> aren't always productive use of your time.
>
> Of course, he could still be waiting to hear from you...
>
Why do people get so damned anal about this stuff? Most of us - or maybe,
some of us don't look at headers to see date stamps. Was it really such a
bother to you that some of us replied?
--
-Mike-
[email protected]
Lew Hodgett wrote:
> [email protected] wrote:
>
>>> I am wondering if you guys should just call the OP and see if he is
>>> still alive. Responding to posts that are nearly THREE years old
>>> aren't always productive use of your time.
>>>
>>> Of course, he could still be waiting to hear from you...
> -----------------------------------------------------------
> "Mike Marlow" wrote:
>
>> Why do people get so damned anal about this stuff? Most of us - or
>> maybe, some of us don't look at headers to see date stamps. Was it
>> really such a bother to you that some of us replied?
> -----------------------------------------------------------
> Picked up a case of upstate New York cabin fever Bunky?
>
> Only a couple of more months.
>
Funny! Almost so true too! I will tell you that this is probably the first
year ever that I just can't wait for winter to be over. Tired of the cold,
had enough snow, just want to be able to pee out on my front lawn again...
--
-Mike-
[email protected]
"Mike Marlow" <[email protected]> wrote
, > just want to be able to pee out on my front lawn again...
You can now, as long as you don't stand still too long and pee ice cubes!
--
Jim in NC
---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com
Morgans wrote:
> "Mike Marlow" <[email protected]> wrote
>
> , > just want to be able to pee out on my front lawn again...
>
> You can now, as long as you don't stand still too long and pee ice
> cubes!
No! I can't! When I tried I peed down the tops of my hip boots...
--
-Mike-
[email protected]
"Mike Marlow" <[email protected]> wrote
>
> No! I can't! When I tried I peed down the tops of my hip boots...
Ahh, my problem, too!
Look for the silver lining in that dark cloud...
It does warm up your feet! <g>
--
Jim in NC
---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com
On Fri, 10 Jun 2011 19:32:17 -0400, Bill <[email protected]> wrote:
>-MIKE- wrote:
>> On 6/10/11 3:21 PM, CW wrote:
>>> "busbus"<[email protected]> wrote in message
>>> news:27a2f258-121a-4097-b274-4b82018ccf6f@w36g2000vbi.googlegroups.com...
>>>> I am in the market and this one seems intriguing. I have some clamps
>>>> and such from them and they are okay--I am not so sure about things
>>>> like air compressors.
>>>>
>>>> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
>>>>
>>>
>>> 150 PSI Chinese bomb. Considering the quality level of HF merchandise
>>> (everywhere from not bad to total crap) I wouldn't trust them with my
>>> life
>>> and that's what you are doing using their air compressor. Odds are though
>>> you won't get the one welded together by the pissed off slave labor.
>>> Feeling
>>> lucky?
>>>
>>
>> So you're one of those guys who thinks an air talk can explode like a
>> bomb, huh?
>>
>
>I assume it's got a safety valve of some sort. What's the skinny?
I haven't checked the stats, but my SWAG is that 98.99% of tanks
develop pinhole leaks which expand, )1% blow at the seams sans
shrapnel, and the other 0.01% have pressure relief valves stick (how
much overpressure can a cheap pump put out, anyway?) and they actually
explode, hurting someone. Here's the nastiest one I could find in ten
minutes. <giggle> http://goo.gl/I5ab8
Seam ruptures on a 21 gallon tank put (15psia empty, 150psi full) 210
gallons of air into the shop in a short amount of time, blowing out
the windows and making the ears smart a bit, wot?
--
The ultimate result of shielding men from the
effects of folly is to fill the world with fools.
--Herbert Spencer
On Jun 12, 10:57=A0pm, Larry Jaques <[email protected]>
wrote:
> On Sun, 12 Jun 2011 11:36:27 -0700 (PDT), Robatoy
>
> <[email protected]> wrote:
> >On Jun 12, 12:04=A0am, Larry Jaques <[email protected]>
> >wrote:
> >> I was thinking Penthouse style, unless you like much older women.
>
> >There is an 18 year difference between Ang and I, so 'older' isn't my
> >bag.
>
> "Ang and me", and where the -hell- are thos pics? =A0<g>
>
Ang and I need to go through and select which pictures are
publishable.
On Sun, 12 Jun 2011 11:36:27 -0700 (PDT), Robatoy
<[email protected]> wrote:
>On Jun 12, 12:04Â am, Larry Jaques <[email protected]>
>wrote:
>> I was thinking Penthouse style, unless you like much older women.
>>
>
>There is an 18 year difference between Ang and I, so 'older' isn't my
>bag.
"Ang and me", and where the -hell- are thos pics? <g>
--
The ultimate result of shielding men from the
effects of folly is to fill the world with fools.
--Herbert Spencer
"busbus" <[email protected]> wrote in message
news:27a2f258-121a-4097-b274-4b82018ccf6f@w36g2000vbi.googlegroups.com...
>I am in the market and this one seems intriguing. I have some clamps
> and such from them and they are okay--I am not so sure about things
> like air compressors.
>
> http://www.harborfreight.com/25-hp-21-gallon-120-volt-125-psi-cast-iron-vertical-air-compressor-67847.html
150 PSI Chinese bomb. Considering the quality level of HF merchandise
(everywhere from not bad to total crap) I wouldn't trust them with my life
and that's what you are doing using their air compressor. Odds are though
you won't get the one welded together by the pissed off slave labor. Feeling
lucky?
On Jun 12, 12:04=A0am, Larry Jaques <[email protected]>
wrote:
> On Sat, 11 Jun 2011 15:32:37 -0700 (PDT), Robatoy
>
>
>
>
>
> <[email protected]> wrote:
> >On Jun 11, 1:52=A0pm, Larry Jaques <[email protected]>
> >wrote:
> >> On Sat, 11 Jun 2011 09:44:59 -0700 (PDT), Angela Sekeris
>
> >> <[email protected]> wrote:
> >> >On Jun 11, 12:14=A0pm, Larry Jaques
>
> >> >> That was probably not more than 3bar, not the 10 we're talking with=
a
> >> >> compressor. =A0But the point is made.
>
> >> >I'm usually pretty well toasted after 10 bars.
>
> >> Hi, Angie. Have Toy take some nice pictures and email 'em, OK?
> >> Say, after 2 bars? =A0<wink>
>
> >Weiner style?
>
> I don't think I want to know what you meant by that.
>
> I was thinking Penthouse style, unless you like much older women.
>
> --
> The ultimate result of shielding men from the
> effects of folly is to fill the world with fools.
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0--Herbert =
Spencer
There is an 18 year difference between Ang and I, so 'older' isn't my
bag.
On Sat, 11 Jun 2011 15:32:37 -0700 (PDT), Robatoy
<[email protected]> wrote:
>On Jun 11, 1:52Â pm, Larry Jaques <[email protected]>
>wrote:
>> On Sat, 11 Jun 2011 09:44:59 -0700 (PDT), Angela Sekeris
>>
>> <[email protected]> wrote:
>> >On Jun 11, 12:14Â pm, Larry Jaques
>>
>> >> That was probably not more than 3bar, not the 10 we're talking with a
>> >> compressor. Â But the point is made.
>>
>> >I'm usually pretty well toasted after 10 bars.
>>
>> Hi, Angie. Have Toy take some nice pictures and email 'em, OK?
>> Say, after 2 bars? Â <wink>
>
>Weiner style?
I don't think I want to know what you meant by that.
I was thinking Penthouse style, unless you like much older women.
--
The ultimate result of shielding men from the
effects of folly is to fill the world with fools.
--Herbert Spencer