Hello, I am new to routing and just purchased my first router and was
doing some practice runs and had a question. I am attempting to round
over a 3/4 thick piece of oak. I never seem to be able to get both
sides of my round over to match, completing a nice smooth round over.
I am running the router by hand, not in a table. is there a easy way
to deciede the correct size of round over bit for a thickness of wood
and should your roundovers meet nice and smooth in the middle or do you
always has to come back with a sander to match them up? Thanks
OK, I was going to elaborate, I was thinking....what I am having
problems with is of course now I have figured out that I would need to
use a 3/8 inch bit for 3/4 inch wood to round it over...but what
happens is after routing one edge...when I go to do the second edge my
ball bearing guide must ride too far in, (the round over I just cut)
and makes the second round over deeper than the first.
The full (1/2) round with an offset fence:
http://patwarner.com/routertable_jointing.html
********************************************************
winty03 wrote:
> Hello, I am new to routing and just purchased my first router and was
> doing some practice runs and had a question. I am attempting to round
> over a 3/4 thick piece of oak. I never seem to be able to get both
> sides of my round over to match, completing a nice smooth round over.
> I am running the router by hand, not in a table. is there a easy way
> to deciede the correct size of round over bit for a thickness of wood
> and should your roundovers meet nice and smooth in the middle or do you
> always has to come back with a sander to match them up? Thanks
winty03 wrote:
> Hello, I am new to routing and just purchased my first router and was
> doing some practice runs and had a question. I am attempting to round
> over a 3/4 thick piece of oak. I never seem to be able to get both
> sides of my round over to match, completing a nice smooth round over.
This is hard to do, so don't try. If you try to get it _exactly_ right,
then you might cut too much or too little. Too much of a cut raises a
sharp arris that's noticeable. If instead you attempt to cut just a bit
too little, it's a lot easier to get an acceptable result.
A radius of half the thickness (or a smidgeon less) and then adjust the
height until it doesn't quite cut a "quirk" The diameter is usually
fixed by the guide bearing, which ought to be accurate.
There's also the problem of tilting the router base by accident, which
will tend to cut a false quirk. Try to hold it level, or switch to a
table.
Carbide cutters are the only sort worth bothering about. 1/2" is
favoured over 1/4". Good brands do make a difference, but you can
usefully get a full set of cheap ones to start with. Read Pat Warner's
excellent router website too.
> I am running the router by hand, not in a table.
Get a table, or make one. It's very easy, even when you make your own
fence.
http://codesmiths.com/shed/workshop/techniques/router_table/
I rarely use a router freehand, nearly everything happens in the table.
winty03 wrote:
> Hello, I am new to routing and just purchased my first router and was
> doing some practice runs and had a question. I am attempting to round
> over a 3/4 thick piece of oak. I never seem to be able to get both
> sides of my round over to match, completing a nice smooth round over.
> I am running the router by hand, not in a table. is there a easy way
> to deciede the correct size of round over bit for a thickness of wood
> and should your roundovers meet nice and smooth in the middle or do you
> always has to come back with a sander to match them up? Thanks
if your bit has a guide post or bearing it needs a surface to follow,
so you normally get a small flat in the center of the curve.
You either need a table mounted router with a fence or you can clamp a
guide in place that the router base plate will follow. This works well
on wide shelving but requires very careful setup , or a jig.
When I want to do this I make the first cut with the router mounted in a
router table and the bit and it's bearing positioned to give me the curve
that I want. Then I move the router table fence into position and align the
fence surface with the bearing surface and I flip the board over to make the
second cut. I don't move the router bit height at all. The bearing doesn't
actually get used for the second cut as there is no material in the proper
position for the bearing to ride on. The fence takes it's place. This will
give an equal curve from each edge to the center. Still, some light sanding
may be required, but it will be very negligable.
--
Charley
"Lee Gordon" <[email protected]> wrote in message
news:[email protected]...
> <<I have figured out that I would need to
> use a 3/8 inch bit for 3/4 inch wood to round it over...but what
> happens is after routing one edge...when I go to do the second edge my
> ball bearing guide must ride too far in, (the round over I just cut)
> and makes the second round over deeper than the first.>>
>
> Raise the bit a little so you leave a little flat spot in the middle for
the
> bearing to ride on when you cut the other side. You will, of course have
to
> do some sanding to make it completely rounded. Of course, by doing it on
a
> router table you can take the bearing out of the equasion.
>
> Lee
>
>
> --
> To e-mail, replace "bucketofspam" with "dleegordon"
>
> _________________________________
> Lee Gordon
> http://www.leegordonproductions.com
>
>
winty03 wrote:
> OK, I was going to elaborate, I was thinking....what I am having
> problems with is of course now I have figured out that I would need to
> use a 3/8 inch bit for 3/4 inch wood to round it over...but what
> happens is after routing one edge...when I go to do the second edge my
> ball bearing guide must ride too far in, (the round over I just cut)
> and makes the second round over deeper than the first.
>
You could rout the second cut from the edge with the guide running down
the flat side of the board. Not easy to do without a router table.
--
Gerald Ross
Cochran, GA
An eye for an eye leaves the whole
world blind
<<I have figured out that I would need to
use a 3/8 inch bit for 3/4 inch wood to round it over...but what
happens is after routing one edge...when I go to do the second edge my
ball bearing guide must ride too far in, (the round over I just cut)
and makes the second round over deeper than the first.>>
Raise the bit a little so you leave a little flat spot in the middle for the
bearing to ride on when you cut the other side. You will, of course have to
do some sanding to make it completely rounded. Of course, by doing it on a
router table you can take the bearing out of the equasion.
Lee
--
To e-mail, replace "bucketofspam" with "dleegordon"
_________________________________
Lee Gordon
http://www.leegordonproductions.com
Yes sanding will be required absed on your description.
To obtain the results you are looking for is best accomplished on a router
table with an offset fence, and even then there will be some sanding
required if you are useing a 1/4 round over bit. You could use a bull nose
bit which cuts both edges at the same time, but again you will need a table
with an offset fence.
Good luck
Joe
"winty03" <[email protected]> wrote in message
news:[email protected]...
> Hello, I am new to routing and just purchased my first router and was
> doing some practice runs and had a question. I am attempting to round
> over a 3/4 thick piece of oak. I never seem to be able to get both
> sides of my round over to match, completing a nice smooth round over.
> I am running the router by hand, not in a table. is there a easy way
> to deciede the correct size of round over bit for a thickness of wood
> and should your roundovers meet nice and smooth in the middle or do you
> always has to come back with a sander to match them up? Thanks
>
"winty03" <[email protected]> wrote in message
news:[email protected]...
> Hello, I am new to routing and just purchased my first router and was
> doing some practice runs and had a question. I am attempting to round
> over a 3/4 thick piece of oak. I never seem to be able to get both
> sides of my round over to match, completing a nice smooth round over.
> I am running the router by hand, not in a table. is there a easy way
> to deciede the correct size of round over bit for a thickness of wood
> and should your roundovers meet nice and smooth in the middle or do you
> always has to come back with a sander to match them up? Thanks
The reason you will need to always sand based on your description of your
technique is that on the second pass, the bearing is not riding on the
square edge as happens on the first pass. Instead it rides on part of the
round that you just cut, which is inside of the square edge. That is what
produces the aris on the tip of the completed bullnose. This is why you
should perform this in the router table with a fence. Even then, you will
probably have to sand a little, just a lot less than routing by hand.
JC
>
You may be able to do better by using an edge guide which will ride on the
very uncut nose centered between each cut.
Tim
"winty03" <[email protected]> wrote in message
news:[email protected]...
> Hello, I am new to routing and just purchased my first router and was
> doing some practice runs and had a question. I am attempting to round
> over a 3/4 thick piece of oak. I never seem to be able to get both
> sides of my round over to match, completing a nice smooth round over.
> I am running the router by hand, not in a table. is there a easy way
> to deciede the correct size of round over bit for a thickness of wood
> and should your roundovers meet nice and smooth in the middle or do you
> always has to come back with a sander to match them up? Thanks
>
If I understand your question correctly, you are trying to do something that
a "roundover" bit was not intended to do. The feature you are trying to
create is called a "bullnose"; and, while it can be created by using a
roundover bit in a router table it is almost impossible to create freehand.
A roundover feature is a relief of only one corner of an edge. A bullnose
is an edge feature that has both corners of the edge rounded the same amount
to create a full radiused edge. Bullnose bits were created to produce this
profile and they can do it freehand. While it may be possible to use edge
guides or other careful freehand procedures and some creative sanding to
accomplish a bullnose profile with a roundover bit, it is far easier to just
use a bullnose bit.
Jim Seelye
"winty03" <[email protected]> wrote in message
news:[email protected]...
> Hello, I am new to routing and just purchased my first router and was
> doing some practice runs and had a question. I am attempting to round
> over a 3/4 thick piece of oak. I never seem to be able to get both
> sides of my round over to match, completing a nice smooth round over.
> I am running the router by hand, not in a table. is there a easy way
> to deciede the correct size of round over bit for a thickness of wood
> and should your roundovers meet nice and smooth in the middle or do you
> always has to come back with a sander to match them up? Thanks
>