I am reading Leonard Lee's book "The complete guide to sharpening" and I
have a couple of questions:
1) I have acquired an old rusty plane. It is 14" long and has No5 in relief
just ahead of the front handle and no other markings. The handles are wood
and the sole plate is ridged. Any ideas on age, quality etc.? Is it worth
sharpening as a beginner project?
2) I have a Craftsman chisel set complete with 3 chisels, a very small plane
and a sharpening stone. Is there any way to tell if this is an oil stone
or a water stone? Can oilstones be used as water stones?
Any help much appreciated,
Jack Fearnley
Any "old" hand tool is worth restoring, in my opinion, especially if
you do the work yourself. Plus the satisfaction of bringing "it" to
life and experiencing the thrill of using the plane after who knows how
long it sat idle or how many previous owners used it?
Clean it up! Tune it up, (Fine Woodworking, issue July/Aug '87, Shop
Notes #36 or best "The handplane book" by Garrett hack!) Pick up some
nice monocrystaline diamond stones, (I prefer DMT's, available from
most good catalogs) and a honing guide, ( the "Sharpening Sled",
www.alisam.com), and sharpen the iron.
Good luck, and have fun!
Tim
Jack Fearnley wrote:
> I am reading Leonard Lee's book "The complete guide to sharpening" and I
> have a couple of questions:
>
> 1) I have acquired an old rusty plane. It is 14" long and has No5 in relief
> just ahead of the front handle and no other markings. The handles are wood
> and the sole plate is ridged. Any ideas on age, quality etc.? Is it worth
> sharpening as a beginner project?
>
> 2) I have a Craftsman chisel set complete with 3 chisels, a very small plane
> and a sharpening stone. Is there any way to tell if this is an oil stone
> or a water stone? Can oilstones be used as water stones?
Everybody else has covered most of the questions, so I'll ask you this
one. What kind of "very small plane"? Block plane or bench plane.
PLEASE don't clean it before we find out. It *could* be a horrible
mistake.
Dave in Fairfax
Jack Fearnley wrote:
> Please note, the plane I am cleaning is a large old No. 5 bench plane. I
> only described the plane in the Craftsman chisel set to help you identify
> the set and therefore the stone that comes with it. The chisels and plane
> in the set are brand new and I am not cleaning or restoring them. I may,
> of course, sharpen and hone them once I am smart enough to do so.
> I hope this sets your mind at rest. Again, thanks to all who responded with
> advice and encouragement.
Glad to hear it. I had this horrible flash of you cleaning up a #1 with
muriatic acid.
Dave in Fairfax
lgb wrote:
> An estate sale I was at yesterday had two #8s, one corrugated and one
> not, for $30 each. Unfortunately I already have a #8, but I paid $60
> for mine :-).
You're allowed to have more than one of any givne plane, I think it's a
law, in fact. Lord knows, I do.
Dave in Fairfax
--
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.patinatools.com
Patriarch wrote:
> Yeah. What's wrong with having three #8s? One of them would have been
> corrugated, after all.
> Too much is just about enough, right?
Too much is barely enough! 'Course SWMBO looks at me funny sometimes.
I like to have my planes set up just slightly differently in each group
so that I can switch easily without having to change settings. LOTS of
planes are a requirement, not an option. 'Sides, if you're slightly
larger than average a #6 feels like a #5 so #7s & #8s are a gimme.
Dave in Fairfax
--
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.patinatools.com
Patriarch wrote:
> >Yeah. What's wrong with having three #8s?
Andy Dingley wrote:
> Gravitational collapse in the tool cabinet.
Well, yeah, there is that. I go for reinforced shelves and lots of
them. I generally get about 12 planes per shelf then start laying block
planes on the heels.
Dave in Fairfax
--
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.patinatools.com
firstjois wrote:
> Mae West said that too much of a good thing is wonderful!
I would never disagree with a lady. Or Mme West.
Dave in Fairfax
--
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.patinatools.com
On Wed, 08 Jun 2005 17:51:10 -0400, Jack Fearnley <[email protected]>
wrote:
>1) I have acquired an old rusty plane. It is 14" long and has No5
It's probably a Stanley, by sheer law of averages. It'll be a very
useful first plane and is certainly worth restoring to usable condition.
The planes:
http://www.supertool.com/StanleyBG/stan0a.html
Dating it:
Long:
http://www.tooltrip.com/tooltrip8/stanley/stan-bpl/bailey-types.htm
Short:
http://www.geocities.com/Heartland/Plains/9147/flowchart.html
Restoring and using it:
http://www.amgron.clara.net/planingpoints/planeindex.htm
Google for "electrolysis" if you want to take rust off it.
>2) I have a Craftsman chisel set complete with 3 chisels, a very small plane
>and a sharpening stone. Is there any way to tell if this is an oil stone
>or a water stone?
Almost certainly an oil stone. Probably not desperately good quality, or
particularly fine either. Worth using, but if you're at the level of
reading Leonard lee, you might start looking at better stones too.
>Can oilstones be used as water stones?
Clean oilstones can. Once they've been used with oil you pretty much
have to stay with it. Neither are "waterstones" in the Japanese sense,
as they're much harder and don't form a slurry. However water works OK
as a lubricant, especially for finer stones.
--
Cats have nine lives, which is why they rarely post to Usenet.
On Sun, 12 Jun 2005 22:44:43 -0500, Patriarch
<[email protected]> wrote:
>Yeah. What's wrong with having three #8s?
Gravitational collapse in the tool cabinet.
Andy Dingley wrote:
> On Wed, 08 Jun 2005 17:51:10 -0400, Jack Fearnley <[email protected]>
> wrote:
>
>>1) I have acquired an old rusty plane. It is 14" long and has No5
>
> It's probably a Stanley, by sheer law of averages. It'll be a very
> useful first plane and is certainly worth restoring to usable condition.
>
> The planes:
> http://www.supertool.com/StanleyBG/stan0a.html
>
> Dating it:
> Long:
> http://www.tooltrip.com/tooltrip8/stanley/stan-bpl/bailey-types.htm
> Short:
> http://www.geocities.com/Heartland/Plains/9147/flowchart.html
>
> Restoring and using it:
> http://www.amgron.clara.net/planingpoints/planeindex.htm
>
> Google for "electrolysis" if you want to take rust off it.
>
>>2) I have a Craftsman chisel set complete with 3 chisels, a very small
>>plane
>>and a sharpening stone. Is there any way to tell if this is an oil stone
>>or a water stone?
>
> Almost certainly an oil stone. Probably not desperately good quality, or
> particularly fine either. Worth using, but if you're at the level of
> reading Leonard lee, you might start looking at better stones too.
>
>>Can oilstones be used as water stones?
>
> Clean oilstones can. Once they've been used with oil you pretty much
> have to stay with it. Neither are "waterstones" in the Japanese sense,
> as they're much harder and don't form a slurry. However water works OK
> as a lubricant, especially for finer stones.
>
>
Thanks for the links and the information. I appear to have a Stanley No. 5
plane circa 1932. I have taken most of the rust off with muriatic acid
(HCl) and Evapo-Rust. Now I have to start to "tune" it.
By the way, I've never sharpened anything. I'm reading L. Lee to find out
how.
Best Regards,
Jack Fearnley
In article <[email protected]>, [email protected] says...
>
> Glad to hear it. I had this horrible flash of you cleaning up a #1 with
> muriatic acid.
>
An estate sale I was at yesterday had two #8s, one corrugated and one
not, for $30 each. Unfortunately I already have a #8, but I paid $60
for mine :-).
--
BNSF = Build Now, Seep Forever
Dave in Fairfax <[email protected]> wrote in
news:[email protected]:
> lgb wrote:
>> An estate sale I was at yesterday had two #8s, one corrugated and one
>> not, for $30 each. Unfortunately I already have a #8, but I paid $60
>> for mine :-).
>
> You're allowed to have more than one of any givne plane, I think it's a
> law, in fact. Lord knows, I do.
>
> Dave in Fairfax
Yeah. What's wrong with having three #8s? One of them would have been
corrugated, after all.
Too much is just about enough, right?
Patriarch
In article <[email protected]>,
Jack Fearnley <[email protected]> wrote:
> I am reading Leonard Lee's book "The complete guide to sharpening" and I
> have a couple of questions:
>
> 1) I have acquired an old rusty plane. It is 14" long and has No5 in relief
> just ahead of the front handle and no other markings. The handles are wood
> and the sole plate is ridged. Any ideas on age, quality etc.? Is it worth
> sharpening as a beginner project?
it's definitely worth doing a good tune up and sharpening to. it'll
teach you a lot about how a handplane works. if nothing is seriously
wrong with it it will probably be a fine working tool, well worth
keeping sharp and at hand.
>
> 2) I have a Craftsman chisel set complete with 3 chisels, a very small plane
> and a sharpening stone. Is there any way to tell if this is an oil stone
> or a water stone? Can oilstones be used as water stones?
I hardly ever use oil on a stone. if water is too thin a fluid I'll use
a drop of dish detergent. if the stone has been used with oil already
the detergent will over time clean it up.
the stone that comes with a set of sears chisels is likely too coarse to
be useful.
>
> Any help much appreciated,
> Jack Fearnley
>
Dave in Fairfax wrote:
> Jack Fearnley wrote:
>> I am reading Leonard Lee's book "The complete guide to sharpening" and I
>> have a couple of questions:
>>
>> 1) I have acquired an old rusty plane. It is 14" long and has No5 in
>> relief
>> just ahead of the front handle and no other markings. The handles are
>> wood
>> and the sole plate is ridged. Any ideas on age, quality etc.? Is it
>> worth sharpening as a beginner project?
>>
>> 2) I have a Craftsman chisel set complete with 3 chisels, a very small
>> plane
>> and a sharpening stone. Is there any way to tell if this is an oil stone
>> or a water stone? Can oilstones be used as water stones?
>
> Everybody else has covered most of the questions, so I'll ask you this
> one. What kind of "very small plane"? Block plane or bench plane.
> PLEASE don't clean it before we find out. It *could* be a horrible
> mistake.
>
> Dave in Fairfax
Please note, the plane I am cleaning is a large old No. 5 bench plane. I
only described the plane in the Craftsman chisel set to help you identify
the set and therefore the stone that comes with it. The chisels and plane
in the set are brand new and I am not cleaning or restoring them. I may,
of course, sharpen and hone them once I am smart enough to do so.
I hope this sets your mind at rest. Again, thanks to all who responded with
advice and encouragement.
Jack Fearnley
On Wed, 08 Jun 2005 17:51:10 -0400, Jack Fearnley
<[email protected]> wrote:
>I am reading Leonard Lee's book "The complete guide to sharpening" and I
>have a couple of questions:
That's a good book.
>
>1) I have acquired an old rusty plane. It is 14" long and has No5 in relief
>just ahead of the front handle and no other markings. The handles are wood
>and the sole plate is ridged. Any ideas on age, quality etc.? Is it worth
>sharpening as a beginner project?
>
Should be well worth the time to clean/tune it up.
>2) I have a Craftsman chisel set complete with 3 chisels, a very small plane
>and a sharpening stone. Is there any way to tell if this is an oil stone
>or a water stone? Can oilstones be used as water stones?
Place it on paper in a warm (110 degree) oven. If the paper shows an
oil spot, it's an oil stone. But you can use oil or water. I use my
small stones as "oil" stones and reserve the large round stones for my
Makita waterston sharpener. I would not put oil on a waterstone, but
would put water on an oil stone.
>
>Any help much appreciated,
> Jack Fearnley
Andy Dingley wrote:
>
> Google for "electrolysis" if you want to take rust off it.
>
>
Several years ago someone far wiser than I posted this and I found it a
"saver." I don't remember who, but if the original writer wants to take
credit, please do.
Get yourself a cheap battery charger, a stainless steel rod, some
(Arm&Hammer "washing soda" (can be found in the laundry section of most
grocery
stores is sold as a "detergent booster"), and a plastic pail full of
water, a
non-abrasive nylon scrubbing pad, a roll of paper towels, and a tin of
carnuba paste wax.
Throw some washing soda in the water and swish it around to dissolve
it. Connect the rusty object to the - Terminal of the charger and place it
in the water, connect the steel rod to the + terminal and submerge it in
the water (make certain the two objects _cannot_ touch each-other... turn
the charger on and witness the bubbles. after a few hours the water should
be pretty disgusting, wherever there _was_ rust will now have a black
film on
it. Wipe the film off w/ the nylon scrubber and dry it _immediately_,
apply the paste wax according to directions on the container.
------------------------------------------------------------------------------------
I have had a couple of requests for this recently and there are a lot
of new subscribers, so here 'tis again. I hope I have covered all the points
so we don't start the thread again.
Q. What is the method?
A. A technique for returning surface rust to iron. It uses the effect
of an small low voltage electric current and a suitable electrolyte
(solution).
Q. What advantages does the method have over the old standbys, like
vinegar, Coke, muriatic acid, Naval Jelly, wire brushing, sand blasting
etc.?
A. These methods all remove material to remove the rust, including
un-rusted surfaces. With many, the metal is left with a "pickled look or a
characteristic
color and texture. The electrolytic method removes nothing: by
returning surface rust to metallic iron, rust scale is loosened and can
be easily
removed. Un-rusted metal is not affected in any way.
Q. What about screws, pivots, etc that are "rusted tight"?
A. The method will frequently solve these problems, without the need
for force, which can break things.
Q. Is it safe?
A. The solutions used are not hazardous; the voltages and currents are
low, so there is no electrical hazard. No noxious fumes are produced. The
method is self-limiting: it is impossible to over clean an object.
Q. Where did this method come from?
A. Electrolysis is a standard technique in the artifact restoration
business. I
wrote this up for the Chronicle of the Early American Industries
Association a
few years back. Most of the tool collectors around here use it:
Q. What do I need?
A. A plastic tub; a stainless steel or iron electrode, water and
washing soda
(NOT baking soda!!) and a battery charger. About a tablespoon of soda
to a
gallon of water. If you have trouble locating the washing soda,
household lye
will work just fine. It's a tad more nasty--always wear eye protection
and be
sure to add the lye to the water (NOT water to lye!!!) The solution is
weak,
and
is not harmful, though you might want to wear gloves.
Q. How long does the solution last?
A. Forever, though the loosened rust will make it pretty disgusting
after a
while. Evaporation and electrolysis will deplete the water from the
solution.
Add water ONLY to bring the level back.
Q. What about the iron electrode?
A. The iron electrode works best if it surrounds the object to be
cleaned, since the cleaning is "line of sight" to a certain extent. The
iron electrode will be eaten away with time. Stainless steel has the
advantage (some alloys,
but not all) that it is not eaten away.
Q. How do I connect the battery charger?
A.THE POLARITY IS CRUCIAL!! The iron or stainless electrode is
connected to the positive (red) terminal. The object being cleaned, to
the negative (black). Submerge the object, making sure you have good
contact, which can be difficult with heavily rusted objects.
Q. How do I know if it is working?
A. Turn on the power. If your charger has a meter, be sure come
current is
flowing. Again, good electrical contact may be hard to make-it is
essential.
Fine bubbles will rise from the object.
Q. How long do I leave it?
A. The time depends on the size of the object and of the iron
electrode, and on
the amount of rust. You will have to test the object by trying to wipe
off the
rust. If it is not completely clean, try again. Typical cleaning time
for
moderately rusted objects is a few hours. With heavily rusted objects
can be
left over night.
Q. How do I get the rust off after I remove the object?
A. Rub the object under running water. A paper towel will help. For
heavily
rusted objects, a plastic pot scrubber can be used, carefully.
Depending on the
amount of original rust, you may have to re-treat.
Q. My object is too big to fit. Can I clean part of it?
A. Yes. You can clean one end and then the other. Lap marks should be
minimal
if
the cleaning was thorough.
Q. After I take it out, then what?
A. The clean object will acquire surface rust very quickly, so wipe it
dry and
dry further in a warm oven or with a hair dryer. You may want to apply
light oil or a coat of wax to prevent further rusting.
Q. Will the method remove pitting?
A. No. It only operates on the rust in immediate contact with unrusted
metal.
What's gone is gone.
Q. What will it look like when I am done?
A. The surface of rusted metal is left black. Rusted pits are still
pits. Shiny
unrusted metal is untouched.
Q. What about nickel plating, paint, japanning and the like?
A. Sound plating will not be affected. Plating under which rust has
penetrated
will usually be lifted. The solution may soften some paints. Test with
a drop
of
solution in an inconspicuous place. Remove wood handles if possible
before
treating.
Q. How can I handle objects that are awkward to clean?
A. There are lots of variants: suspending an electrode inside to clean
a cavity
in an object; using a sponge soaked in the electrolyte with a backing
electrode
to clean spots on large objects or things that shouldn't be submerged
(like
with
lots of wood)
Q. How can I dispose of the solution?
A. The bath will last until it gets so disgusting that you decide it
is time
for
a fresh one. There is nothing especially nasty about it-it's mildly
basic-so
disposal is not a concern, except you may not want all the crud in
your drains.
Q. Can I use metal containers?
A. This is highly risky. Galvanized metal can introduce zinc into the
solution.
If you have used lye, it will attack aluminum. You may have problems
with
electrical shorts, etc. Stick to plastic.
Q. How can I clean odd shaped objects?
A. Be ingenious. Plastic PVC pipe and eave troughs, wooden boxes with
poly vapor barrier.
Glen
Dave in Fairfax wrote:
>> Patriarch wrote:
>>> Yeah. What's wrong with having three #8s? One of them would have
>>> been corrugated, after all.
>>> Too much is just about enough, right?
>>
>> Too much is barely enough! 'Course SWMBO looks at me funny
>> sometimes. I like to have my planes set up just slightly differently
>> in each group so that I can switch easily without having to change
>> settings. LOTS of planes are a requirement, not an option. 'Sides,
>> if you're slightly larger than average a #6 feels like a #5 so #7s &
>> #8s are a gimme.
>>
>> Dave in Fairfax
>> --
Mae West said that too much of a good thing is wonderful!
Josie