I ran into an old friend last week while Christmas shopping. I hadn't seen
him in quite some time so it was a pleasant surprise to run into him. He
had a large woodworking shop so I of course asked him what he'd been making
lately. He immediatly held up his left hand displaying what was left of his
fingers. Every finger, including the thumb was half as long as they should
have been after being cut off by a chop saw. He admitted to doing just
about everything wrong. To start with, one of the fingers on that hand was
in a splint from a previous accident. He was in a hurry. Cutting a short
piece of wood, the splint, being longer than his finger, got caught by the
blade and pulled all his fingers into the blade.
I can only imagine the look on my face while hearing about this accident. I
hope I never have to hear about another one and will take great steps so
that I never have to explain an accident of my own like that one.
Please be careful while woodworking. Body parts are hard to replace.
Bryan
I saw a guy loose 3 fingers.
A friend of mine (a nurse) picked up the fingers
put them in salty ice-water (similar to blood), and brought them to the
hospital.
The guy had all 3 reattached. They all work fine.
"DamnYankeeBastard" <[email protected]> wrote in message
news:[email protected]...
>I ran into an old friend last week while Christmas shopping. I hadn't seen
> him in quite some time so it was a pleasant surprise to run into him. He
> had a large woodworking shop so I of course asked him what he'd been
> making
> lately. He immediatly held up his left hand displaying what was left of
> his
> fingers. Every finger, including the thumb was half as long as they
> should
> have been after being cut off by a chop saw. He admitted to doing just
> about everything wrong. To start with, one of the fingers on that hand
> was
> in a splint from a previous accident. He was in a hurry. Cutting a short
> piece of wood, the splint, being longer than his finger, got caught by the
> blade and pulled all his fingers into the blade.
>
> I can only imagine the look on my face while hearing about this accident.
> I
> hope I never have to hear about another one and will take great steps so
> that I never have to explain an accident of my own like that one.
>
> Please be careful while woodworking. Body parts are hard to replace.
>
> Bryan
>
>
Dave in Fairfax wrote:
> Salt alone is bad, ice alone is bad, cold
> saltwater, and remember the OP said to make it basically a normal
> saline solution (not his exact words), is good.
>
> Dave in Fairfax
We were taught to take an eyewash bottle of sterile saline and use that
to contain the parts, optrex sell long bottles here that are std.
polyfusion (for I.V. use) relabled as emergency eyewash so is suppose
they should be good for that!
Ya know, I've had this idea in my head for some time, to make a miter saw
safer. Set aside the obvoius safety issues with sticking your fingers too
close to the blade, the actual piece being cut can be a more common hazard.
I'm sure most of you have cut something small, like a return for a piece of
shoe moulding, and heard a loud "CACHINK" followed by the piece leaving the
saw at similiar speed in which a TS saw can throw something. Being a
carpenter, cutting small pieces is routine and I've learned to just "be
careful" cutting small pieces and get on with my day. Recently i've been
thinking about how to "prevent" this from happening. My idea involves
creating a zero clearance insert for the fence of a miter saw. That would
allow the small piece to be supprorted in the back and preventing the blade
from throwing that little sucker out of there. Miter saws all have the same
problem- the fence is spread to far apart. This is partially done to
accomodate bevel cuts, and therein lies the problem with creating a ZCI.
But i'm sure i could demise something.
Hmmmm.. anyone got an new MS, maybe a Bosch 4410, to donate for research?
;) --dave
"Swingman" <[email protected]> wrote in message
news:[email protected]...
> "mac davis" wrote in message
>
>> I got my CMS a few years ago and almost immediately screwed up by
>> trying to cut a piece that was too short to safely cut using a CMS..
>> the piece moved (as it almost had to) a bit and bound the blade,
>> causing the stock (a 5 or 6" piece of 4x4) to twist and get a 1/2"
>> curved gash on a sort of diagonal line... about where my hand was
>> before I let go...
>> I was SO lucky, and I appreciate that.. but I was also incredibly
>> stupid... If in doubt, I'll clamp it and keep my hands far from the
>> blade, or find another way to make the cut..
>
> I mention if for the obvious reasons.
>
> I did much the same thing in what I hope were my stupid(er) days, on a
> little longer piece of wood than you (thank gawd) that I FAILED to snug up
> against the fence, because I was trying to increase the angle a bit
> (powered
> miter saws were fairly new then and you learned by experience). I did!
>
> I'll never forget the speed with which that blade snatched the piece of
> wood
> and slammed it against the fence, with my fingers first. I was lucky to
> only
> lose four fingernails from the incident.
>
> Every since then I have had a healthy respect for the quickness, and power
> to do harm, of miter and chop saws.
>
> wheewww ... still shudder when I think about it.
>
> --
> www.e-woodshop.net
> Last update: 11/06/04
>
>
Dave Jackson wrote:
> ...
> creating a zero clearance insert for the fence of a miter saw. That would
> allow the small piece to be supprorted in the back and preventing the blade
> from throwing that little sucker out of there. Miter saws all have the same
> problem- the fence is spread to far apart. This is partially done to
> accomodate bevel cuts, and therein lies the problem with creating a ZCI.
> But i'm sure i could demise something.
...
I have a piece of 1x that I shaped free hand to fit in the gap...I just
sketched the opening shape on the front and routed off the thickness of
the fence so it fits "flush enough" to the front of the fence...then I
just clamp it in place when doing a bunch of the type of small stuff
you're talking about. A more permanently fabricated one would be nice,
but it <does> help significantly.
If I have a lot of a specific trim I also make a cradle for the front to
hold small moldings so don't have to hold them by hand as well...one
gradually builds a collection for various standard shapes.
makesawdust wrote:
> I know this who was changing a light bulb while standing on a folding
> chair, the chair broke, he grabbed a pipe above his head, his ring got
> caught on a screw or rivet, at he tore his finger off. Another guy
> packed it it ice, but by the time they got to the hospital the finger
> had been too damaged by the cold to be attached. The doctor said that
> you should wrap the finger in a clean cloth and pack the cloth in ice.
You missed the part about the ICED SALT WATER. The ice alone, and
the dryness, is what damaged the finger.
Dave in Fairfax
--
Dave Leader
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.Patinatools.org/
Mike Marlow wrote:
> Hmmmmm... never heard of that. Not suggesting it's wrong, but in all of my
> emergency medical training we had always been told not to use ice directly -
> no mention of salt.
Absolutely correct. Packing it in ice is VERY bad, just as it
would be if the finger was still attached. Putting it in water,
saltwater is better, keeps the tissues from drying out, icing the
water keeps the tissues from decomposing and decreases the O2
requirements. Salt alone is bad, ice alone is bad, cold
saltwater, and remember the OP said to make it basically a normal
saline solution (not his exact words), is good.
Dave in Fairfax
--
Dave Leader
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.Patinatools.org/
Badger wrote:
> We were taught to take an eyewash bottle of sterile saline and use that
> to contain the parts, optrex sell long bottles here that are std.
> polyfusion (for I.V. use) relabled as emergency eyewash so is suppose
> they should be good for that!
Sounds like a plan. what I was thinking is that most people
('cept here where everybody is a medical/computer type) don't
stock NSS. In that situation, a bowl, come icewater and a dash of
salt is something that ANYBODY can come up with in a hurry. Me' I
keep the Respiratory NSS bullets for trache care around, they can
point and squirt or pour. Good for eyewashers, too.
Dave in Fairfax
--
Dave Leader
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.Patinatools.org/
When I was younger, 12 or 13 years old, I was using a circular saw to
cut up some pieces to make a box. I had the board hanging over the side of
a chair and started to make a cut. The blade on the saw bound up and threw
the saw back into my left leg plunging the whole blade in. Tendons and
artery were severed and as a result, I hit the floor with blood gushing
everywhere. I remember pulling off my to shirt and belt and making a
tourniquet to stop the bleeding. Mom was hysterical, but managed to call
for an ambulance. I remember feeling really light headed and very cold on
the ride to the hospital, and the EMT's rushing me into the OR as I was
losing consciousness. My parents said shortly thereafter, they were
approached by a nurse who suggested calling in the Father of the church to
give final rites "just in case".....
Anyhow, the good Lord must have had other plans in mind for me, cuz two
weeks later i dropped the crutches and was walking again. The scar i have
starts very close to the family jewels and extends down my left leg about
10" or so and is my personal reminder to think about safety.
Ironically, i grew up to become a carpenter and use a circular saw
pretty much daily. In fact, i still use the same saw that almost ended my
life for demo work on rare occasions. (oddly enough)
Anyway, this is my testament to the importance of safety. --dave
"ddinc" <[email protected]> wrote in message
news:[email protected]...
>I saw a guy loose 3 fingers.
> A friend of mine (a nurse) picked up the fingers
> put them in salty ice-water (similar to blood), and brought them to the
> hospital.
>
> The guy had all 3 reattached. They all work fine.
>
>
> "DamnYankeeBastard" <[email protected]> wrote in message
> news:[email protected]...
>>I ran into an old friend last week while Christmas shopping. I hadn't
>>seen
>> him in quite some time so it was a pleasant surprise to run into him. He
>> had a large woodworking shop so I of course asked him what he'd been
>> making
>> lately. He immediatly held up his left hand displaying what was left of
>> his
>> fingers. Every finger, including the thumb was half as long as they
>> should
>> have been after being cut off by a chop saw. He admitted to doing just
>> about everything wrong. To start with, one of the fingers on that hand
>> was
>> in a splint from a previous accident. He was in a hurry. Cutting a
>> short
>> piece of wood, the splint, being longer than his finger, got caught by
>> the
>> blade and pulled all his fingers into the blade.
>>
>> I can only imagine the look on my face while hearing about this accident.
>> I
>> hope I never have to hear about another one and will take great steps so
>> that I never have to explain an accident of my own like that one.
>>
>> Please be careful while woodworking. Body parts are hard to replace.
>>
>> Bryan
>>
>>
>
>
"mac davis" wrote in message
> I got my CMS a few years ago and almost immediately screwed up by
> trying to cut a piece that was too short to safely cut using a CMS..
> the piece moved (as it almost had to) a bit and bound the blade,
> causing the stock (a 5 or 6" piece of 4x4) to twist and get a 1/2"
> curved gash on a sort of diagonal line... about where my hand was
> before I let go...
> I was SO lucky, and I appreciate that.. but I was also incredibly
> stupid... If in doubt, I'll clamp it and keep my hands far from the
> blade, or find another way to make the cut..
I mention if for the obvious reasons.
I did much the same thing in what I hope were my stupid(er) days, on a
little longer piece of wood than you (thank gawd) that I FAILED to snug up
against the fence, because I was trying to increase the angle a bit (powered
miter saws were fairly new then and you learned by experience). I did!
I'll never forget the speed with which that blade snatched the piece of wood
and slammed it against the fence, with my fingers first. I was lucky to only
lose four fingernails from the incident.
Every since then I have had a healthy respect for the quickness, and power
to do harm, of miter and chop saws.
wheewww ... still shudder when I think about it.
--
www.e-woodshop.net
Last update: 11/06/04
Dave in Fairfax wrote:
>> Mike Marlow wrote:
>>> Hmmmmm... never heard of that. Not suggesting it's wrong, but in
>>> all of my emergency medical training we had always been told not to
>>> use ice directly - no mention of salt.
>>
>> Absolutely correct. Packing it in ice is VERY bad, just as it
>> would be if the finger was still attached. Putting it in water,
>> saltwater is better, keeps the tissues from drying out, icing the
>> water keeps the tissues from decomposing and decreases the O2
>> requirements. Salt alone is bad, ice alone is bad, cold
>> saltwater, and remember the OP said to make it basically a normal
>> saline solution (not his exact words), is good.
>>
>> Dave in Fairfax
And normal saline is a teaspoon of salt per quart of water.
Josie
"DamnYankeeBastard" wrote in message
> Every finger, including the thumb was half as long as they should
> have been after being cut off by a chop saw.
Chop and miter saws ... for a tool that many folks think is rather benign,
there are few tools in the shop where these same folks would put their
fingers that close to the action.
--
www.e-woodshop.net
Last update: 11/06/04
LMYO! "demo" short for "demolition" not "demonstration" --dave
"Old Nick" <[email protected]> wrote in message
news:[email protected]...
> On Tue, 28 Dec 2004 18:34:08 GMT, "Dave Jackson" <[email protected]>
> vaguely proposed a theory
> ......and in reply I say!:
>
> remove ns from my header address to reply via email
>
>> Ironically, i grew up to become a carpenter and use a circular saw
>>pretty much daily. In fact, i still use the same saw that almost ended my
>>life for demo work on rare occasions. (oddly enough)
>
> Demos of what?
>
> "Anyway, this is my testament to the importance of safety."
>
> Don't do it like....oh damn!
> <GG>
>
On Tue, 28 Dec 2004 08:55:40 -0600, "Swingman" <[email protected]> wrote:
>"DamnYankeeBastard" wrote in message
>
>> Every finger, including the thumb was half as long as they should
>> have been after being cut off by a chop saw.
>
>Chop and miter saws ... for a tool that many folks think is rather benign,
>there are few tools in the shop where these same folks would put their
>fingers that close to the action.
I got my CMS a few years ago and almost immediately screwed up by
trying to cut a piece that was too short to safely cut using a CMS..
the piece moved (as it almost had to) a bit and bound the blade,
causing the stock (a 5 or 6" piece of 4x4) to twist and get a 1/2"
curved gash on a sort of diagonal line... about where my hand was
before I let go...
I was SO lucky, and I appreciate that.. but I was also incredibly
stupid... If in doubt, I'll clamp it and keep my hands far from the
blade, or find another way to make the cut..
mac
Please remove splinters before emailing
On Tue, 28 Dec 2004 18:34:08 GMT, "Dave Jackson" <[email protected]>
vaguely proposed a theory
......and in reply I say!:
remove ns from my header address to reply via email
> Ironically, i grew up to become a carpenter and use a circular saw
>pretty much daily. In fact, i still use the same saw that almost ended my
>life for demo work on rare occasions. (oddly enough)
Demos of what?
"Anyway, this is my testament to the importance of safety."
Don't do it like....oh damn!
<GG>
"Dave Jackson" <[email protected]> wrote in message
news:[email protected]...
> Ya know, I've had this idea in my head for some time, to make a miter
saw
> safer. Set aside the obvoius safety issues with sticking your fingers too
> close to the blade, the actual piece being cut can be a more common
hazard.
> I'm sure most of you have cut something small, like a return for a piece
of
> shoe moulding, and heard a loud "CACHINK" followed by the piece leaving
the
> saw at similiar speed in which a TS saw can throw something. Being a
> carpenter, cutting small pieces is routine and I've learned to just "be
> careful" cutting small pieces and get on with my day. Recently i've been
> thinking about how to "prevent" this from happening. My idea involves
> creating a zero clearance insert for the fence of a miter saw. That
would
> allow the small piece to be supprorted in the back and preventing the
blade
> from throwing that little sucker out of there. Miter saws all have the
same
> problem- the fence is spread to far apart. This is partially done to
> accomodate bevel cuts, and therein lies the problem with creating a ZCI.
> But i'm sure i could demise something.
>
I was walking the dog one day and saw a finish carpenter doing some work on
the neighbor's house. He had some big chunk of wood he was moving around
with each cut. I was intrigued and went up to him and asked what he was
doing.
He had a number of "freehand clamps". The operated much like those
hydraulic clamps on the commercial saws. But his were ultimate simplicity.
He would take a chink of wood and make a rabbet on one edge. He would then
affix a handle at a 15 degree angle. He would line up his wood for the cut
with this big wood clamp on it. He then pushed the clamp against the back
fence. The stock was held very securely by a much bigger block of wood. His
hand was always a foot from the blade.
He needed a very strong and solid miter saw bench setup to do this. He said
that he got tired of always having to think of his finger and witnessed
other accidents and did not want to become a statistic. He just basically
came up with a neander version of the commercial hydraulic clamps. And as
for short peices, he just put some stock behind the clamp block to make it
secure.
Now I know that it is difficult for some folks to visualize this from a
verbal description. So I will describe the block used for cutting 2 X 4's.
He had a chunk of 4 X 4. He cut a rabbet that was a little shallower than
the 2 X 4. He cut it at least one half the width (or more) than what he was
cutting. So this big chunk of wood wrapped around one corner of the smaller
peice without touching the saw bed. He then screwed a piece of plysood to
the top with a wood handle attached. The wood handle was just a large dowel
set into two other peices of wood. Nothing fancy.
So he lays the notched 4 X 4 over the 2 X 4. He pushed the handle back and
down. The miter say is secred to a strong table that will not slide. This
locks the wood securely in place without having to have his hand near the
blade.
He told me he tried to work out jigs that use those destaco clamps. But he
cut so many different types of wood, that he would need a whole bunch of
specialized jigs and have to set each one up individually. Which would take
a lot of time. That is why he went to the notched block approach. He makes
up one block for each type of wood he cuts. Then it lasts for years.
He would make up a bunch of handles out of plywood and dowels. Then anytime
he needed another block, he just cut out a wrap around peice (a rabbet) and
attached the handle. The handles were definitely the most time consuming
part.
He was good too. He cut off the trim just as fast if not faster than anyone
doing this kind of work. Only he did it in aboslute safety.
I hope the explanation is adequate. I just saw it and him using it. So I
am going from memory here. But I thought it was a good approach. And fairly
simple as well.
Lee Michaels
On Tue, 28 Dec 2004 17:10:55 GMT, "Keith" <[email protected]>
wrote:
>I posted this a short while ago....It's just as scary, so here it is again.
>
>I recently learned that two weeks ago an old friend almost lost his arm
>above the wrist when his sleeve got caught by the chop saw blade, dragged
>his arm in and cut it to just short of the tendons and main artery. His son
>told me the arm was hanging down.....His father grabbed it and pushed it
>against the other severed section, then ran across the street to get a
>neighbor to call an ambulance.
I bought a 12" CMS recently and after using it a few times
I decided to attach a 10" length of 1 X 4 to the fence, about
10" to the left of the blade, 2.5" above the table, with the end
butted into the saw fence. This sets the minimum distance
from my hand to the blade and hopefully would put the 1X4
between me and the blade if something goes wrong. I'm
not sure that I'm not creating other problems by doing this;
let me know if you can think of any.
ddinc Wrote:
> I saw a guy loose 3 fingers.
> A friend of mine (a nurse) picked up the fingers
> put them in salty ice-water (similar to blood), and brought them t
> the
> hospital.
>
> The guy had all 3 reattached. They all work fine.
>
>
> "DamnYankee*******" [email protected] wrote in message
> news:[email protected]
> I ran into an old friend last week while Christmas shopping. I hadn'
> seen
> him in quite some time so it was a pleasant surprise to run into him.
> He
> had a large woodworking shop so I of course asked him what he'd been
> making
> lately. He immediatly held up his left hand displaying what was lef
> of
> his
> fingers. Every finger, including the thumb was half as long as they
> should
> have been after being cut off by a chop saw. He admitted to doin
> just
> about everything wrong. To start with, one of the fingers on tha
> hand
> was
> in a splint from a previous accident. He was in a hurry. Cutting
> short
> piece of wood, the splint, being longer than his finger, got caught b
> the
> blade and pulled all his fingers into the blade.
>
> I can only imagine the look on my face while hearing about thi
> accident.
> I
> hope I never have to hear about another one and will take great step
> so
> that I never have to explain an accident of my own like that one.
>
> Please be careful while woodworking. Body parts are hard to replace.
>
> Bryan
>
> -
I know this who was changing a light bulb while standing on a foldin
chair, the chair broke, he grabbed a pipe above his head, his ring go
caught on a screw or rivet, at he tore his finger off. Another gu
packed it it ice, but by the time they got to the hospital the finge
had been too damaged by the cold to be attached. The doctor said tha
you should wrap the finger in a clean cloth and pack the cloth in ice
--
makesawdust
On Thu, 30 Dec 2004 19:56:42 GMT, "Dave Jackson" <[email protected]>
vaguely proposed a theory
......and in reply I say!:
remove ns from my header address to reply via email
My confusion was honest, but I am glad I could provide a moment's
chuckle. <G>.
>LMYO! "demo" short for "demolition" not "demonstration" --dave
On Tue, 28 Dec 2004 20:41:21 -0500, "Lee Michaels"
<leemichaels*nadaspam*@comcast.net> wrote:
<snip>
>Now I know that it is difficult for some folks to visualize this from a
>verbal description. So I will describe the block used for cutting 2 X 4's.
>
>He had a chunk of 4 X 4. He cut a rabbet that was a little shallower than
>the 2 X 4. He cut it at least one half the width (or more) than what he was
>cutting. So this big chunk of wood wrapped around one corner of the smaller
>peice without touching the saw bed. He then screwed a piece of plysood to
>the top with a wood handle attached. The wood handle was just a large dowel
>set into two other peices of wood. Nothing fancy.
>
>So he lays the notched 4 X 4 over the 2 X 4. He pushed the handle back and
>down. The miter say is secred to a strong table that will not slide. This
>locks the wood securely in place without having to have his hand near the
>blade.
>
<snip>
That sounds very much like the router table jigs I use, just on a
bigger scale..
never hurts to be a little further from that spinning bit..
mac
Please remove splinters before emailing
"Dave in Fairfax" <[email protected]> wrote in message
news:[email protected]...
> makesawdust wrote:
> > I know this who was changing a light bulb while standing on a folding
> > chair, the chair broke, he grabbed a pipe above his head, his ring got
> > caught on a screw or rivet, at he tore his finger off. Another guy
> > packed it it ice, but by the time they got to the hospital the finger
> > had been too damaged by the cold to be attached. The doctor said that
> > you should wrap the finger in a clean cloth and pack the cloth in ice.
>
> You missed the part about the ICED SALT WATER. The ice alone, and
> the dryness, is what damaged the finger.
>
Hmmmmm... never heard of that. Not suggesting it's wrong, but in all of my
emergency medical training we had always been told not to use ice directly -
no mention of salt.
--
-Mike-
[email protected]
I posted this a short while ago....It's just as scary, so here it is again.
I recently learned that two weeks ago an old friend almost lost his arm
above the wrist when his sleeve got caught by the chop saw blade, dragged
his arm in and cut it to just short of the tendons and main artery. His son
told me the arm was hanging down.....His father grabbed it and pushed it
against the other severed section, then ran across the street to get a
neighbor to call an ambulance.
Doctors spent three hours doing what they could to prepare him for airlift
to a larger hospital some 500 miles away.
Once there, he spent 9 hours in surgery. They must have done a miraculous
job because he was able to move his fingers within a few hours after! He
was a VERY lucky man.
Bottom line - Don't look away while you're cutting and don't wear long
sleeves....It only takes a second. Makes me think that one of those
instant-stop devices might not be such a bad idea. I guess Nahm's repeated
safety tips aren't such a bad idea after all :O)
Keith P