Long winded subject but anyway. I have been using Cabot's ATO on my
Mahogany deck for around 4 years now. Reapply every year per
instructions on can. So far so good. Water beads up nicely and
squeegies off like glass. Issue I have now is the color. I have been
using the "Mahogany Flame" color since day one. When I first used it,
the grain on the wood planks was much more visible. Now the wood is
very dark, almost black. Little if any grain visible. I assume this is
due to a build up of the pigments in the stain and/or oxidation. I
would like to bring back the origional appearance, lighten it up. Short
of sanding the deck completely is there anything else I can do? I have
thought about using the clear ATO instead of the flame and perhaps hand
rubbing the old stuff off with a solvent or maybe the clear ATO itself
will act as a solvent and remove the old stuff. I cleaned the deck this
past weekend with a mild detergent/ bleach solution, no change
whatsoever. Your comments and advice would be appreciated. Thanks.
john
"jk" <[email protected]> wrote in message
news:[email protected]...
> Long winded subject but anyway. I have been using Cabot's ATO on my
> Mahogany deck for around 4 years now. Reapply every year per
> instructions on can. So far so good. Water beads up nicely and
> squeegies off like glass. Issue I have now is the color. I have been
> using the "Mahogany Flame" color since day one. When I first used it,
> the grain on the wood planks was much more visible. Now the wood is
> very dark, almost black. Little if any grain visible. I assume this is
> due to a build up of the pigments in the stain and/or oxidation. I
> would like to bring back the origional appearance, lighten it up. Short
> of sanding the deck completely is there anything else I can do? I have
> thought about using the clear ATO instead of the flame and perhaps hand
> rubbing the old stuff off with a solvent or maybe the clear ATO itself
> will act as a solvent and remove the old stuff. I cleaned the deck this
> past weekend with a mild detergent/ bleach solution, no change
> whatsoever. Your comments and advice would be appreciated. Thanks.
> john
>
Before you go to the trouble of stripping it you may want to borrow or rent
a high pressure washer. It may just be ground in dirt and the washer may
bring back some of the grain. Look for the one with the most PSI .
Jim
Well, I started this so I figured I'd jump back in. Sent Cabot's an
email detailing the issue with the ATO on the Mahogany deck, color
build up, etc. Also inquired as to the use of pressure washers. Will
let you guys know what they say. Take care.
john
Jim Northey wrote:
> "Edwin Pawlowski" <[email protected]> wrote in message
> news:z_bSg.1388$0Y2.607@trndny09...
> >
> > "Jim Northey" <[email protected]> wrote in message
> > news:zj1Sg.37445$5R2.15953@pd7urf3no...
> >> And just how is a pressure washer going to destroy the wood ?
> >> Jim
> >
> > Depends on the operator. I fine jet will make grooves in the wood. It
> > will tear up the fibers. While it won't destroy it completely, it can
> > look like crap if done wrong.
> >
> Yes on that I agree. But one would hope that the operator would test first
> on a small area before blindly pushing on without checking. At least I
> would. But then when I think of most of the people I work with I've got to
> wonder. I don't have a T shirt saying ( Just when I thought people can't
> get any stupider.... I'm proven horribly wrong) for nothing . (-;
> Jim
do your self a favor and don't blast the hell out of your wood with a
pressure washer
that's just bad advice
talk to the supplier that sold you the Cabot product before you destroy your
wood
they might be able to give you some good well thought out advice
"Jim Northey" <[email protected]> wrote in message
news:0J_Rg.37619$R63.4937@pd7urf1no...
>
> "jk" <[email protected]> wrote in message
> news:[email protected]...
> > Long winded subject but anyway. I have been using Cabot's ATO on my
> > Mahogany deck for around 4 years now. Reapply every year per
> > instructions on can. So far so good. Water beads up nicely and
> > squeegies off like glass. Issue I have now is the color. I have been
> > using the "Mahogany Flame" color since day one. When I first used it,
> > the grain on the wood planks was much more visible. Now the wood is
> > very dark, almost black. Little if any grain visible. I assume this is
> > due to a build up of the pigments in the stain and/or oxidation. I
> > would like to bring back the origional appearance, lighten it up. Short
> > of sanding the deck completely is there anything else I can do? I have
> > thought about using the clear ATO instead of the flame and perhaps hand
> > rubbing the old stuff off with a solvent or maybe the clear ATO itself
> > will act as a solvent and remove the old stuff. I cleaned the deck this
> > past weekend with a mild detergent/ bleach solution, no change
> > whatsoever. Your comments and advice would be appreciated. Thanks.
> > john
> >
> Before you go to the trouble of stripping it you may want to borrow or
rent
> a high pressure washer. It may just be ground in dirt and the washer may
> bring back some of the grain. Look for the one with the most PSI .
> Jim
>
>
I had a very similar issue. I used the pressure washer route on my
mahogany deck with very good success. I kept the pressure to a minimum
and use light passes to try to avoid removing too much of the "color".
After letting the deck dry I reapplied the oil as usual.
roemax wrote:
> do your self a favor and don't blast the hell out of your wood with a
> pressure washer
> that's just bad advice
> talk to the supplier that sold you the Cabot product before you destroy your
> wood
> they might be able to give you some good well thought out advice
>
>
> "Jim Northey" <[email protected]> wrote in message
> news:0J_Rg.37619$R63.4937@pd7urf1no...
>> "jk" <[email protected]> wrote in message
>> news:[email protected]...
>>> Long winded subject but anyway. I have been using Cabot's ATO on my
>>> Mahogany deck for around 4 years now. Reapply every year per
>>> instructions on can. So far so good. Water beads up nicely and
>>> squeegies off like glass. Issue I have now is the color. I have been
>>> using the "Mahogany Flame" color since day one. When I first used it,
>>> the grain on the wood planks was much more visible. Now the wood is
>>> very dark, almost black. Little if any grain visible. I assume this is
>>> due to a build up of the pigments in the stain and/or oxidation. I
>>> would like to bring back the origional appearance, lighten it up. Short
>>> of sanding the deck completely is there anything else I can do? I have
>>> thought about using the clear ATO instead of the flame and perhaps hand
>>> rubbing the old stuff off with a solvent or maybe the clear ATO itself
>>> will act as a solvent and remove the old stuff. I cleaned the deck this
>>> past weekend with a mild detergent/ bleach solution, no change
>>> whatsoever. Your comments and advice would be appreciated. Thanks.
>>> john
>>>
>> Before you go to the trouble of stripping it you may want to borrow or
> rent
>> a high pressure washer. It may just be ground in dirt and the washer may
>> bring back some of the grain. Look for the one with the most PSI .
>> Jim
>>
>>
>
>
"jk" <[email protected]> wrote in message
news:[email protected]...
> Well, I started this so I figured I'd jump back in. Sent Cabot's an
> email detailing the issue with the ATO on the Mahogany deck, color
> build up, etc. Also inquired as to the use of pressure washers. Will
> let you guys know what they say. Take care.
> john
Thanks. Should be interesting to see what they say about the washer, seeing
as most of the people I know with one use it for that plus siding and
fences. As Ed stated in his post about grooves I can see that happening but
would think the operator would notice and change his technique ....or at
least sit down with a few beers and think, cool a no slip surface :-) Well
that would be my answer for it and I'd stick to it.
Jim
"Edwin Pawlowski" <[email protected]> wrote in message
news:z_bSg.1388$0Y2.607@trndny09...
>
> "Jim Northey" <[email protected]> wrote in message
> news:zj1Sg.37445$5R2.15953@pd7urf3no...
>> And just how is a pressure washer going to destroy the wood ?
>> Jim
>
> Depends on the operator. I fine jet will make grooves in the wood. It
> will tear up the fibers. While it won't destroy it completely, it can
> look like crap if done wrong.
>
Yes on that I agree. But one would hope that the operator would test first
on a small area before blindly pushing on without checking. At least I
would. But then when I think of most of the people I work with I've got to
wonder. I don't have a T shirt saying ( Just when I thought people can't
get any stupider.... I'm proven horribly wrong) for nothing . (-;
Jim
"Jim Northey" <[email protected]> wrote in message
news:zj1Sg.37445$5R2.15953@pd7urf3no...
> And just how is a pressure washer going to destroy the wood ?
> Jim
Depends on the operator. I fine jet will make grooves in the wood. It will
tear up the fibers. While it won't destroy it completely, it can look like
crap if done wrong.
And just how is a pressure washer going to destroy the wood ?
Jim
"roemax" <fsteddie2000@[email protected]> wrote in message
news:2p0Sg.4339$8j4.2264@trndny05...
> do your self a favor and don't blast the hell out of your wood with a
> pressure washer
> that's just bad advice
> talk to the supplier that sold you the Cabot product before you destroy
> your
> wood
> they might be able to give you some good well thought out advice
>
>
> "Jim Northey" <[email protected]> wrote in message
> news:0J_Rg.37619$R63.4937@pd7urf1no...
>>