see the center hole in the second slide? that is to clamp glued up board to=
the arbor. angled blade brought into the spinning work and cuts through. =
remove outer ring , reposition blade, and cut next ring. Other tools/method=
s may work but I know a RingMaster can do this. I see these guys sometimes =
at craft fairs.
Gramps' shop wrote:
> I assume the author uses a bandsaw to cut the concentric circles
> here:
>
> http://www.michaelmode.com/technique.html
>
> Can't figure out how he does so without cutting an entry access to
> each ring. Any ideas?
-------------------------------------------------------
"G. Ross" wrote:
> Drills a small hole and uses a scroll saw.
-----------------------------------------------------
Definitely scroll saw time.
Lew
Check out: http://scrollsawbowls.blogspot.com/
Carol does some great bowls from flat boards.
Looks like Michael takes it a step further.
>I assume the author uses a bandsaw to cut the concentric circles here:
>http://www.michaelmode.com/technique.html
>Can't figure out how he does so without cutting an entry access to each ring. Any ideas?
>Larry [Gramps' shop]
"Lew Hodgett" wrote in message
news:[email protected]...
Gramps' shop wrote:
> I assume the author uses a bandsaw to cut the concentric circles here:
>
> http://www.michaelmode.com/technique.html
>
> Can't figure out how he does so without cutting an entry access to each
> ring. Any ideas?
-------------------------------------------------------
"G. Ross" wrote:
> Drills a small hole and uses a scroll saw.
-----------------------------------------------------
Definitely scroll saw time.
I've seen cuts started with jig saws by tilting the saw forward and
letting the blade eat into the wood.
Dave in Texas
"Gramps' shop" <[email protected]> wrote in news:74ed0542-d2d9-493b-9fb9-
[email protected]:
> I assume the author uses a bandsaw to cut the concentric circles here:
>
> http://www.michaelmode.com/technique.html
>
> Can't figure out how he does so without cutting an entry access to each ring. Any ideas?
Think scrollsaw instead of bandsaw.
G. Ross wrote:
> Gramps' shop wrote:
>> I assume the author uses a bandsaw to cut the concentric circles here:
>>
>> http://www.michaelmode.com/technique.html
>>
>> Can't figure out how he does so without cutting an entry access to each ring. Any ideas?
>>
>> Larry
> Drills a small hole and uses a scroll saw.
>
The table is angled for sawing, otherwise the rings would not stack
up. Forgot to mention this.
--
GW Ross
Weird enough for all practical
purposes.
http://www.ringmasterlathe.com/
Martin
On 8/29/2013 3:53 PM, Pat Barber wrote:
> On 8/29/2013 10:23 AM, willshak wrote:
>
>> OK. We were diverted into the use of a band or jig saw. No one mentioned
>> a lathe, not even you until BillinGA mentioned a Ringmaster.
>> http://www.youtube.com/watch?v=2n4uY9oJ-tA
>
> The Ringmaster is the way to do the segmented bowls in my opinion.
>
> I saw one in action in a local woodworker show and I was stunned at
> what the guy could crank out in just a few minutes.
>
> After you have made a few hundred bowls, I'm not sure where you go
> after that....but you can really crank out bowls with that tool.
>
> An interesting side fact was that the RingMaster "was" made in a
> plant in Wilmington, NC that built Porta-Nail floor nailers.
>
> That plant closed a few years back and I don't know where the
> RingMaster went....
>
>
>
>
>
>
>
>
>
>
Scroll saw is the only practical method. I have made a few of them.
Some pictures of finished product and how it is done can be seen at:
http://ray80538.home.comcast.net/~ray80538/SegmentedBowl/segbowl.html
On Wed, 28 Aug 2013 13:36:28 -0700 (PDT), "Gramps' shop"
<[email protected]> wrote:
>I assume the author uses a bandsaw to cut the concentric circles here:
>
>http://www.michaelmode.com/technique.html
>
>Can't figure out how he does so without cutting an entry access to each ring. Any ideas?
>
>Larry
On 8/28/2013 4:36 PM, Gramps' shop wrote:
> I assume the author uses a bandsaw to cut the concentric circles here:
>
> http://www.michaelmode.com/technique.html
>
> Can't figure out how he does so without cutting an entry access to each ring. Any ideas?
>
> Larry
>
Scroll saw. its fine enough that a you drill a small hole and the blade
fits in.
Surprised that this is glued up. Some of these are made collapseable.
--
Jeff
"Gramps' shop" <[email protected]> wrote in
message
news:[email protected]
> I assume the author uses a bandsaw to cut the concentric
> circles here:
>
> http://www.michaelmode.com/technique.html
>
> Can't figure out how he does so without cutting an entry
> access to each ring. Any ideas?
>
> Larry
1. No hole needed, just cut out the outside ring.
2. Cut the next ring. It was the second in, is now outside, no hole needed.
3. Keep doing #2
--
dadiOH
____________________________
Winters getting colder? Tired of the rat race?
Taxes out of hand? Maybe just ready for a change?
Check it out... http://www.floridaloghouse.net
dadiOH wrote:
> "Gramps' shop" <[email protected]> wrote in
> message
> news:[email protected]
>> I assume the author uses a bandsaw to cut the concentric
>> circles here:
>>
>> http://www.michaelmode.com/technique.html
>>
>> Can't figure out how he does so without cutting an entry
>> access to each ring. Any ideas?
>>
>> Larry
>
> 1. No hole needed, just cut out the outside ring.
>
> 2. Cut the next ring. It was the second in, is now outside, no hole needed.
>
> 3. Keep doing #2
>
Do you want to rethink that?
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeros after @
"willshak" <[email protected]> wrote in message
news:[email protected]
> dadiOH wrote:
> > "Gramps' shop" <[email protected]> wrote in
> > message
> > news:[email protected]
> > > I assume the author uses a bandsaw to cut the
> > > concentric circles here:
> > >
> > > http://www.michaelmode.com/technique.html
> > >
> > > Can't figure out how he does so without cutting an
> > > entry access to each ring. Any ideas?
> > >
> > > Larry
> >
> > 1. No hole needed, just cut out the outside ring.
> >
> > 2. Cut the next ring. It was the second in, is now
> > outside, no hole needed. 3. Keep doing #2
> >
>
> Do you want to rethink that?
Why?
--
dadiOH
____________________________
Winters getting colder? Tired of the rat race?
Taxes out of hand? Maybe just ready for a change?
Check it out... http://www.floridaloghouse.net
In article <[email protected]>,
Gramps' shop <[email protected]> wrote:
>I assume the author uses a bandsaw to cut the concentric circles here:
>
>http://www.michaelmode.com/technique.html
>
>Can't figure out how he does so without cutting an entry access to each
>ring. Any ideas?
>
>Larry
Could be done on a scroll saw (drill a small hole first & thread the
blade through it) or with some custom hole saws. Could also cut access for
band saw at one of the joints between dark & light wood, then reglue.
--
The best argument against democracy is a five-minute conversation
with the average voter. (Winston Churchill)
Larry W. - Baltimore Maryland - lwasserm(a)sdf. lonestar. org
dadiOH wrote:
> "willshak" <[email protected]> wrote in message
> news:[email protected]
>> dadiOH wrote:
>>> "Gramps' shop" <[email protected]> wrote in
>>> message
>>> news:[email protected]
>>>> I assume the author uses a bandsaw to cut the
>>>> concentric circles here:
>>>>
>>>> http://www.michaelmode.com/technique.html
>>>>
>>>> Can't figure out how he does so without cutting an
>>>> entry access to each ring. Any ideas?
>>>>
>>>> Larry
>>> 1. No hole needed, just cut out the outside ring.
>>>
>>> 2. Cut the next ring. It was the second in, is now
>>> outside, no hole needed. 3. Keep doing #2
>>>
>> Do you want to rethink that?
>
> Why?
>
When you cut the outside edge of the outside ring, how do you get the
saw inside the outside ring to cut the next smaller ring without cutting
into the outside ring?
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeros after @
willshak wrote:
> dadiOH wrote:
>> "willshak" <[email protected]> wrote in message
>> news:[email protected]
>>> dadiOH wrote:
>>>> "Gramps' shop" <[email protected]> wrote in
>>>> message
>>>> news:[email protected]
>>>>> I assume the author uses a bandsaw to cut the
>>>>> concentric circles here:
>>>>>
>>>>> http://www.michaelmode.com/technique.html
>>>>>
>>>>> Can't figure out how he does so without cutting an
>>>>> entry access to each ring. Any ideas?
>>>>>
>>>>> Larry
>>>> 1. No hole needed, just cut out the outside ring.
>>>>
>>>> 2. Cut the next ring. It was the second in, is now
>>>> outside, no hole needed. 3. Keep doing #2
>>>>
>>> Do you want to rethink that?
>>
>> Why?
>>
>
> When you cut the outside edge of the outside ring, how do you get the
> saw inside the outside ring to cut the next smaller ring without cutting
> into the outside ring?
>
OK. We were diverted into the use of a band or jig saw. No one mentioned
a lathe, not even you until BillinGA mentioned a Ringmaster.
http://www.youtube.com/watch?v=2n4uY9oJ-tA
--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeros after @
On 8/29/2013 10:23 AM, willshak wrote:
> OK. We were diverted into the use of a band or jig saw. No one mentioned
> a lathe, not even you until BillinGA mentioned a Ringmaster.
> http://www.youtube.com/watch?v=2n4uY9oJ-tA
The Ringmaster is the way to do the segmented bowls in my opinion.
I saw one in action in a local woodworker show and I was stunned at
what the guy could crank out in just a few minutes.
After you have made a few hundred bowls, I'm not sure where you go
after that....but you can really crank out bowls with that tool.
An interesting side fact was that the RingMaster "was" made in a
plant in Wilmington, NC that built Porta-Nail floor nailers.
That plant closed a few years back and I don't know where the
RingMaster went....
Gramps' shop wrote:
> I assume the author uses a bandsaw to cut the concentric circles here:
>
> http://www.michaelmode.com/technique.html
>
> Can't figure out how he does so without cutting an entry access to each ring. Any ideas?
>
> Larry
Drills a small hole and uses a scroll saw.
--
GW Ross
Weird enough for all practical
purposes.