I just had my first real opportunity to prep some rough stock yesterday. I
thought the conservative thing to do would be to set the jointer for very
shallow (about 1/32nd) cuts, and make as many passes as necessary to remove
all of the milling marks on the face of the board. I left the jointer set the
same way to do the edge of the board, once the face was flat.
The results seem OK, but after about a zillion passes, I started to wonder if
this was the proper strategy. Should I have used a more aggressive cut? What
are the factors that I should apply when making this decision?
Thanks.
--
Art Greenberg
artg AT eclipse (remove this) DOT net
Sharpness of knives, hardness of wood, grain orientation, horsepower
and your technique all come into play. While taking off the high spots,
you could probably increase the depth of cut without any problems, but
when face jointing with the full width of your jointer, light cuts give
a better finish, IMO. A light cut allows better technique, too,
resulting in flat faces on thinner stock. I usually leave my depth of
cut between 1/32nd and 1/64th of an inch. Tom
I ususally put the board on a flat surface and estimate the amount to
be removed for a flat surface. If it is 1/4" or more I start with
about 1/8" cut.
I find an initial deep cut easier to manage than multiple passes with a
shallow setting.
Technique is very important to avoid tapers.
I do not often use a jointer much anymore. I have a tablesaw jig that
lets me cut boards for a glueline fit with no jointing. So I usually
pass through table saw and the one pass to remove sawmarks on the
thickness planer.
Art Greenberg wrote:
>
> I just had my first real opportunity to prep some rough stock yesterday. I
> thought the conservative thing to do would be to set the jointer for very
> shallow (about 1/32nd) cuts, and make as many passes as necessary to remove
> all of the milling marks on the face of the board. I left the jointer set the
> same way to do the edge of the board, once the face was flat.
>
> The results seem OK, but after about a zillion passes, I started to wonder if
> this was the proper strategy. Should I have used a more aggressive cut? What
> are the factors that I should apply when making this decision?
>
Whatever you want that works...
"Doug Miller" <[email protected]> wrote in message
news:[email protected]...
> Leads me to think it's the result of an incompetent sawyer, and you should
> be
> buying your lumber somewhere else.
>
Lost of times the dog boards will be thinner at the end. The cant sometimes
warps, especially on super-fresh or reaction wood, plus dogging down in the
wane area tends to push the ends out a bit - opposite wedge.
In article <[email protected]>, John McCoy <[email protected]> wrote:
>"Stephen M" <[email protected]> wrote in
>news:[email protected]:
>
>>> > Why would tapering be a problem? I joint the face, joint the edge
>>> > then rip to width.
>>>
>>> If the board is narrower at the ends than the middle, when you're
>>> edge joining it you need to feed it so only the middle is cut for
>>> the first few passes...otherwise the board will taper from one end
>>> to the other.
>>
>> In general, nature does not make boards that look like that. 99% of
>> the time if a board has a convex edge, the opposide edge is concave.
>
>On the contrary, I see a fair number like that...I don't know if
>it's an effect of different species, or drying technique, or what.
>Boards like that are also usually thicker in the middle than the
>ends, which leads me to think it's an effect of drying.
Leads me to think it's the result of an incompetent sawyer, and you should be
buying your lumber somewhere else.
--
Regards,
Doug Miller (alphageek at milmac dot com)
It's time to throw all their damned tea in the harbor again.
You need to adjust your planer. I cut to length first. Smaller pieces are
much easier to handle. No planer snipe.
"John McCoy" <[email protected]> wrote in message
news:[email protected]...
> "Stephen M" <[email protected]> wrote in
> news:[email protected]:
>
> > Yes, Shallow.
>
> I would dispute this. I use a shallow cut for face jointing,
> because it's hard to maintain a consistant speed & pressure with
> the resistance of the whole width of the board. But for edge
> jointing I'll start with a much more aggressive cut until the
> edge is close to straight, because it makes it easier to control
> the board and avoid tapering it if I make fewer passes.
>
> > Always crosscut to rough length before jointing.
>
> Bad advice, or at least wasteful. You want enough length beyond
> finished length to allow for planer snipe, which means wasting
> 8 or 10 inches on every piece (*). Where the stock allows, I try
> to plan for more than one finished piece from a board, and I
> joint and plane it before cutting to length (for significantly
> non-flat boards I cut first, simply because for those you'd
> end up jointing/planing too much of the board thickness away
> if you didn't)
>
> (* note that you can sometimes save a little stock if you can
> plan your tenons to fall on the sniped end of a board)
>
> John
"Stephen M" <[email protected]> wrote in
news:[email protected]:
> Yes, Shallow.
I would dispute this. I use a shallow cut for face jointing,
because it's hard to maintain a consistant speed & pressure with
the resistance of the whole width of the board. But for edge
jointing I'll start with a much more aggressive cut until the
edge is close to straight, because it makes it easier to control
the board and avoid tapering it if I make fewer passes.
> Always crosscut to rough length before jointing.
Bad advice, or at least wasteful. You want enough length beyond
finished length to allow for planer snipe, which means wasting
8 or 10 inches on every piece (*). Where the stock allows, I try
to plan for more than one finished piece from a board, and I
joint and plane it before cutting to length (for significantly
non-flat boards I cut first, simply because for those you'd
end up jointing/planing too much of the board thickness away
if you didn't)
(* note that you can sometimes save a little stock if you can
plan your tenons to fall on the sniped end of a board)
John
"Stephen M" <[email protected]> wrote in
news:[email protected]:
>> > Yes, Shallow.
>>
>> I would dispute this. I use a shallow cut for face jointing,
>> because it's hard to maintain a consistant speed & pressure with
>> the resistance of the whole width of the board. But for edge
>> jointing I'll start with a much more aggressive cut until the
>> edge is close to straight, because it makes it easier to control
>> the board and avoid tapering it if I make fewer passes.
>
> Why would tapering be a problem? I joint the face, joint the edge then
> rip to width.
If the board is narrower at the ends than the middle, when you're
edge joining it you need to feed it so only the middle is cut for
the first few passes...otherwise the board will taper from one end
to the other.
>> Where the stock allows, I try
>> to plan for more than one finished piece from a board, and I
>> joint and plane it before cutting to length (for significantly
>> non-flat boards I cut first, simply because for those you'd
>> end up jointing/planing too much of the board thickness away
>> if you didn't)
> Well I could not disagree more. Planning to cut that much stock off
> every board is wasteful. Tune you planer to avoid snipe. face-jointing
> a full-length board is wasteful as it requires more stock removal to
> remove the bow from a board. 1/4" bow over eight feet will require
> removal of 1/4" of stock. 2 four-footers from that same board will
> require about 1/16" of stock removal.
As I said, "where the stock allows". Obviously a board which is
not reasonably flat to begin with can't be jointed full-length
without excess loss of thickness, which is exactly what I said
in the parenthesis above.
John
"Stephen M" <[email protected]> wrote in
news:[email protected]:
>> > Why would tapering be a problem? I joint the face, joint the edge
>> > then rip to width.
>>
>> If the board is narrower at the ends than the middle, when you're
>> edge joining it you need to feed it so only the middle is cut for
>> the first few passes...otherwise the board will taper from one end
>> to the other.
>
> In general, nature does not make boards that look like that. 99% of
> the time if a board has a convex edge, the opposide edge is concave.
On the contrary, I see a fair number like that...I don't know if
it's an effect of different species, or drying technique, or what.
Boards like that are also usually thicker in the middle than the
ends, which leads me to think it's an effect of drying.
> Joint the concave edge, then rip the convex edge.
Definately the way to go when there's a concave edge to work with.
John
Yes, Shallow.
I have set at "minimal" and leave it. I'm not sure how many boards you need
to take a zillion passes.
Always crosscut to rough length before jointing. If a board is naturally
flat it takes me 2 or three passes to remove the milling marks. If I have
to remove any serious bow or cup I can usual get a surface withou marks
within 6 passes.
If all the milling marks are gone and the board is not flat (that is smooth
not flat) you have a set-up issue or a technique problem.
-Steve
"Art Greenberg" <[email protected]> wrote in message
news:[email protected]...
> I just had my first real opportunity to prep some rough stock yesterday. I
> thought the conservative thing to do would be to set the jointer for very
> shallow (about 1/32nd) cuts, and make as many passes as necessary to
remove
> all of the milling marks on the face of the board. I left the jointer set
the
> same way to do the edge of the board, once the face was flat.
>
> The results seem OK, but after about a zillion passes, I started to wonder
if
> this was the proper strategy. Should I have used a more aggressive cut?
What
> are the factors that I should apply when making this decision?
>
> Thanks.
>
> --
> Art Greenberg
> artg AT eclipse (remove this) DOT net
> > Yes, Shallow.
>
> I would dispute this. I use a shallow cut for face jointing,
> because it's hard to maintain a consistant speed & pressure with
> the resistance of the whole width of the board. But for edge
> jointing I'll start with a much more aggressive cut until the
> edge is close to straight, because it makes it easier to control
> the board and avoid tapering it if I make fewer passes.
Why would tapering be a problem? I joint the face, joint the edge then rip
to width.
I will concede that taking a bigger bite will get you to flat faster in some
cases, but, for me it's often quicker to take a couple extra passes than to
fiddle with the setup.
>
> > Always crosscut to rough length before jointing.
>
> Bad advice, or at least wasteful. You want enough length beyond
> finished length to allow for planer snipe, which means wasting
> 8 or 10 inches on every piece (*). Where the stock allows, I try
> to plan for more than one finished piece from a board, and I
> joint and plane it before cutting to length (for significantly
> non-flat boards I cut first, simply because for those you'd
> end up jointing/planing too much of the board thickness away
> if you didn't)
>
> (* note that you can sometimes save a little stock if you can
> plan your tenons to fall on the sniped end of a board)
Well I could not disagree more. Planning to cut that much stock off every
board is wasteful. Tune you planer to avoid snipe. face-jointing a
full-length board is wasteful as it requires more stock removal to remove
the bow from a board. 1/4" bow over eight feet will require removal of 1/4"
of stock. 2 four-footers from that same board will require about 1/16" of
stock removal.
If you like to retain as much stock thickness as possible (I often do),
crosscut first.
-Steve
> > Why would tapering be a problem? I joint the face, joint the edge then
> > rip to width.
>
> If the board is narrower at the ends than the middle, when you're
> edge joining it you need to feed it so only the middle is cut for
> the first few passes...otherwise the board will taper from one end
> to the other.
In general, nature does not make boards that look like that. 99% of the time
if a board has a convex edge, the opposide edge is concave.
Joint the concave edge, then rip the convex edge.
On Wed, 21 Sep 2005 13:40:42 GMT, Art Greenberg <[email protected]>
wrote:
>I just had my first real opportunity to prep some rough stock yesterday. I
>thought the conservative thing to do would be to set the jointer for very
>shallow (about 1/32nd) cuts, and make as many passes as necessary to remove
>all of the milling marks on the face of the board. I left the jointer set the
>same way to do the edge of the board, once the face was flat.
>
>The results seem OK, but after about a zillion passes, I started to wonder if
>this was the proper strategy. Should I have used a more aggressive cut? What
>are the factors that I should apply when making this decision?
>
>Thanks.
I generally use aggressive cuts with a shallow final pass, both
jointer and planer. The small last cut gives a smooth surface.
John McCoy <[email protected]> wrote:
>You want enough length beyond
>finished length to allow for planer snipe, which means wasting
>8 or 10 inches on every piece
What kind of planer snipes that far from the end? The worst I've ever
seen was about 2 1/2 ". If I have several pieces to plane, I run
them through nose to tail. Usually only the first board has any snipe,
and I can use a sacrificial scrap for that, so all my work pieces are
snipe-free.
John McCoy wrote:
> Bad advice, or at least wasteful. You want enough length beyond
> finished length to allow for planer snipe, which means wasting
> 8 or 10 inches on every piece (*).
8 or 10 inches! Gadzooks! Sounds like it is time to either adjust your
planer or its tables or shop for a new planer.
-John
On Wed, 21 Sep 2005 13:40:42 GMT, Art Greenberg <[email protected]>
wrote:
>I just had my first real opportunity to prep some rough stock yesterday. I
>thought the conservative thing to do would be to set the jointer for very
>shallow (about 1/32nd) cuts, and make as many passes as necessary to remove
>all of the milling marks on the face of the board. I left the jointer set the
>same way to do the edge of the board, once the face was flat.
>
>The results seem OK, but after about a zillion passes, I started to wonder if
>this was the proper strategy. Should I have used a more aggressive cut? What
>are the factors that I should apply when making this decision?
>
>Thanks.
the default setting on my jointer is <just barely cutting>. I adjust
it for a deeper cut pretty often, though.
Art Greenberg <[email protected]> wrote in
news:[email protected]:
>
>
> I just had my first real opportunity to prep some rough stock
> yesterday. I thought the conservative thing to do would be to set the
> jointer for very shallow (about 1/32nd) cuts, and make as many passes
> as necessary to remove all of the milling marks on the face of the
> board. I left the jointer set the same way to do the edge of the
> board, once the face was flat.
>
Coupl'a thots: (a) I'm usually a shallow person too! :) Jointing and
planing - it's 1/32nd to 1/16th at most. (b) if I'm face jointing a board
with a bad cup/bow/warp - then I'll work it up to 1/8th. As another said
there are a half-dozen other factors to consider.
Also recall that you needn't face joint the board so the entire face is
getting cut - you can sometimes just face joint enuff to present a flat
face to the planer. You then let the planer do the work.
I also have found that I get much better results when I don't push down
hard on the outfeed table. For the initial cuts, I have firm, but not
heavy pressure down on the outfeed table and concentrate more on the
force required to slide the stock horizontally.
At least that's what's been working for me!