On Jan 21, 4:38 pm, davy <[email protected]> wrote:
> What should I use to clean my bandsaw tyres that have sawdust imbedded
> on them. I have carefully scraped the heavier bits off but don't want to
> damage the surface of the rubber.
I just grab a piece of hardwood and hold it at a bit of an angle and
give it a few rotations. Whatever doesn't come off doing that is
going to be back on it in about 10 mins of use anyway.
-Kevin
"Swingman" <[email protected]> wrote in message
news:[email protected]...
>
>
> "davy" wrote
>> What should I use to clean my bandsaw tyres that have sawdust imbedded on
>> them. I have carefully scraped the heavier bits off but don't want to
>> damage the surface of the rubber.
>> Methylated spirits, turps, etc...?
>
> Since you may already have it in the shop, alcohol works good as a cleaner
> for rubber/most synthetic parts.
>
> I used 99% isopropyl for years for cleaning heads, transport guides,
> capstans and pinch rollers for tape decks in the recording studio. AAMOF,
> it was the active ingredient of many of the more expensive head and roller
> cleaners back in the old days of analog recording.
Oddly I used Freon to clean recording heads on ADP computers.
I just watched Duginske's video, which I recommend highly.
One way he does it is to attach some 100 grit sandpaper to a long flat
stick, like a 2 x 3, and turns the wheels to abrade them smooth, while
preserving the curve.
The point of the long stick, maybe 14 inches, is to keep your hand
away from the spinning wheels.
davy <[email protected]> writes:
> What should I use to clean my bandsaw tyres that have sawdust imbedded
> on them. I have carefully scraped the heavier bits off but don't want
> to damage the surface of the rubber.
> Methylated spirits, turps, etc...?
> Thanks,
Suggestion: Get the $7 brush that keeps the tyres clean.
I don't know the UK dealer or price.
On Thu, 22 Jan 2009 08:38:45 +1100, davy <[email protected]> wrote:
>What should I use to clean my bandsaw tyres that have sawdust imbedded
>on them. I have carefully scraped the heavier bits off but don't want to
>damage the surface of the rubber.
>Methylated spirits, turps, etc...?
>Thanks,
>Davy
If these are truly rubber, do not use isopropyl alcohol. Wood alcohol
(methanol) won't hurt the rubber but should not come in contact with
skin and is poisonous. I glue some sandpaper onto a stick and use
that to clean the surface. I have a brass wire brush that leans
against the tire as it rotates. That, with good DC suction, sawdust
can be kept under control.
davy wrote:
> What should I use to clean my bandsaw tyres that have sawdust imbedded
> on them. I have carefully scraped the heavier bits off but don't want to
> damage the surface of the rubber.
> Methylated spirits, turps, etc...?
> Thanks,
> Davy
Not sure if it would clean bandsaw tires, but I had an inkjet printer
that wouldn't grab paper to feed it. I found somewhere on the internet
that recommended cleaning the rubber wheels with half & half windex and
water using a Q-tip. Worked great and the paper has been feeding
without a hitch.
"davy" wrote
> What should I use to clean my bandsaw tyres that have sawdust imbedded on
> them. I have carefully scraped the heavier bits off but don't want to
> damage the surface of the rubber.
> Methylated spirits, turps, etc...?
Since you may already have it in the shop, alcohol works good as a cleaner
for rubber/most synthetic parts.
I used 99% isopropyl for years for cleaning heads, transport guides,
capstans and pinch rollers for tape decks in the recording studio. AAMOF, it
was the active ingredient of many of the more expensive head and roller
cleaners back in the old days of analog recording.
I've also used it on my band saw tires with no problems for years ... outta
the same bottle I use to cut my shellac.
Just do NOT use "acetone" ... :(
FWIW ...
--
www.e-woodshop.net
Last update: 10/22/08
KarlC@ (the obvious)