GG

Greg Guarino

13/03/2015 11:47 AM

Through tenons

I'm between projects at the moment and I'm contemplating the next one. I
try to design in a new technique here and there to improve my skills.
I've been flirting with the idea of through tenons. Given that I have
yet to make even a blind mortise and tenon joint, this may be premature,
but I'm tossing around ideas in my head.

I've got some ideas about how I could make tenons given my limited tool
set, and I figure a plunge router (which I don't have yet) and a
template would take care of a *rounded* mortise. I'm wondering how you
guys square off the mortise. I assume that unless you have a dedicated
mortising machine, you use some sort of chisel(s), but what kind?

Do you use anything special, or just regular chisels? I've seen a corner
chisel, if that's the right term. I don't mean the kind they sell for
hinge mortises. It's a fairly long chisel with two cutting edges at a
right angle. I also see square chisels, which look very much like the
hollow chisels that are used in dedicated mortising machines, but with a
handle to be struck with a mallet. Lastly, I've seen mortising chisels,
which seem to be twice as thick as regular chisels.

Thoughts?


This topic has 13 replies

Ll

Leon

in reply to Greg Guarino on 13/03/2015 11:47 AM

16/03/2015 1:00 PM

On 3/16/2015 9:01 AM, Greg Guarino wrote:
> On 3/16/2015 9:50 AM, Leon wrote:
>> On 3/15/2015 6:37 PM, Greg Guarino wrote:
>>> On 3/14/2015 12:12 PM, Swingman wrote:
>>>> On 3/13/2015 10:47 AM, Greg Guarino wrote:
>>>>> I'm between projects at the moment and I'm contemplating the next
>>>>> one. I
>>>>> try to design in a new technique here and there to improve my skills.
>>>>> I've been flirting with the idea of through tenons. Given that I have
>>>>> yet to make even a blind mortise and tenon joint, this may be
>>>>> premature,
>>>>> but I'm tossing around ideas in my head.
>>>>
>>>>> Thoughts?
>>>>
>>>> Something else to think about if you want to do floating tenons with a
>>>> router.
>>>>
>>>> It's possible to do floating through tenons, with the visible part
>>>> square, giving you a traditional through tenon look.
>>>>
>>>> Because I use a Multi-Router for most of my floating tenon joinery,
>>>> I've
>>>> done this a few times:
>>>>
>>>> https://picasaweb.google.com/111355467778981859077/EWoodShopJigsFixturesMethods?noredirect=1#6126118837123706546
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> In the one shown I did inset the square part in the stile/leg using a
>>>> dedicated mortising machine for a shallow (1/4") square mortise, but
>>>> you
>>>> don't have to.
>>>>
>>>> Just make the visible square part of the tenon long enough for the look
>>>> you want, insert in both parts, glue and pin the joint with a
>>>> contrasting pin, and Bob's your uncle.
>>>>
>>>> The part is that difficult to make once you get started, and there is
>>>> more than one way to skin the cat to fabricate them.
>>>>
>>>> I make them square, then round-over the square edges of the floating
>>>> tenon with a pattern makers file to fit the round mortises cut in the
>>>> stock with the Multi-Router.
>>>>
>>>> Traditional look and strength, modern tools...
>>>>
>>> Well I'd probably never have thought of that. But for the uninitiated,
>>> what's the advantage over the traditional tenon? Just that the rounded
>>> mortises are easier to make, I assume?
>>
>> Absolutely and the over sized square portion that is visible does not
>> have to fit into a mortise.
>
> I was thinking about that. Karl's drawing shows a loose tenon that does
> need to be inset in a mortise that is squared off, at least to a certain
> depth. I see that you could do away with that, by making the "square"
> part only as thick as the visible section. But it strikes me that that
> would make for a very thin edge, unless the visible section is to be
> thicker than usual.
>
Yes, the visible part would be larger to your liking and would cover and
hide the actual mortise and tenon. For strength, floating tenons do not
have to a perfect fit except with the cheeks of the tenon being the same
as the mortise. Length is not so important, you have plenty of contact
glue surface on both sides of the tenon. Floating tenons typically do
not completely fill the mortise anyway, this gives you wiggle room. In
fact the Festool Domino has three width settings for it's fixed width
Domino tenons. Exact fit, and two progressively wider than exact fit
mortise settings.

Dt

DerbyDad03

in reply to Greg Guarino on 13/03/2015 11:47 AM

16/03/2015 8:37 PM

On Sunday, March 15, 2015 at 3:04:42 PM UTC-4, Leon wrote:
> On 3/14/2015 11:12 AM, Swingman wrote:
> > On 3/13/2015 10:47 AM, Greg Guarino wrote:
> >> I'm between projects at the moment and I'm contemplating the next one. I
> >> try to design in a new technique here and there to improve my skills.
> >> I've been flirting with the idea of through tenons. Given that I have
> >> yet to make even a blind mortise and tenon joint, this may be premature,
> >> but I'm tossing around ideas in my head.
> >
> >> Thoughts?
> >
> > Something else to think about if you want to do floating tenons with a
> > router.
> >
> > It's possible to do floating through tenons, with the visible part
> > square, giving you a traditional through tenon look.
>
> AND to expand on that a bit.... you can also do trough tenons and sand
> them flush with the piece that they are going through, the exposed side.
> Don't worry about appearance. Cut a false tenon to glue over the
> actual flush sanded through tenon. It can be slightly larger than the
> actual mortise to cover the "real" joint lines.
>

..and with a little creativity regarding the shape, you could really have people scratching their heads as to how you got it "through" the wood. ;-)

Ll

Leon

in reply to Greg Guarino on 13/03/2015 11:47 AM

16/03/2015 8:50 AM

On 3/15/2015 6:37 PM, Greg Guarino wrote:
> On 3/14/2015 12:12 PM, Swingman wrote:
>> On 3/13/2015 10:47 AM, Greg Guarino wrote:
>>> I'm between projects at the moment and I'm contemplating the next one. I
>>> try to design in a new technique here and there to improve my skills.
>>> I've been flirting with the idea of through tenons. Given that I have
>>> yet to make even a blind mortise and tenon joint, this may be premature,
>>> but I'm tossing around ideas in my head.
>>
>>> Thoughts?
>>
>> Something else to think about if you want to do floating tenons with a
>> router.
>>
>> It's possible to do floating through tenons, with the visible part
>> square, giving you a traditional through tenon look.
>>
>> Because I use a Multi-Router for most of my floating tenon joinery, I've
>> done this a few times:
>>
>> https://picasaweb.google.com/111355467778981859077/EWoodShopJigsFixturesMethods?noredirect=1#6126118837123706546
>>
>>
>>
>> In the one shown I did inset the square part in the stile/leg using a
>> dedicated mortising machine for a shallow (1/4") square mortise, but you
>> don't have to.
>>
>> Just make the visible square part of the tenon long enough for the look
>> you want, insert in both parts, glue and pin the joint with a
>> contrasting pin, and Bob's your uncle.
>>
>> The part is that difficult to make once you get started, and there is
>> more than one way to skin the cat to fabricate them.
>>
>> I make them square, then round-over the square edges of the floating
>> tenon with a pattern makers file to fit the round mortises cut in the
>> stock with the Multi-Router.
>>
>> Traditional look and strength, modern tools...
>>
> Well I'd probably never have thought of that. But for the uninitiated,
> what's the advantage over the traditional tenon? Just that the rounded
> mortises are easier to make, I assume?

Absolutely and the over sized square portion that is visible does not
have to fit into a mortise.



JM

John McCoy

in reply to Greg Guarino on 13/03/2015 11:47 AM

13/03/2015 4:35 PM

Greg Guarino <[email protected]> wrote in news:mdv0o8$gf9$1@dont-
email.me:

> I figure a plunge router (which I don't have yet) and a
> template would take care of a *rounded* mortise. I'm wondering how you
> guys square off the mortise. I assume that unless you have a dedicated
> mortising machine, you use some sort of chisel(s), but what kind?
>
> Do you use anything special, or just regular chisels?

Regular chisels for me. If it's a thru mortise, cut in from
both sides so the cut is clean at the edges. If the chisel
strays a little in the middle of the mortise it's no problem.

Corner chisels look like a neat idea, but they're hard to
find and hard to sharpen, so a regular chisel is just
simpler.

John

JM

John McCoy

in reply to Greg Guarino on 13/03/2015 11:47 AM

13/03/2015 10:22 PM

"dadiOH" <[email protected]> wrote in news:[email protected]:

> Step #1
> Decide whether you want square corner or rounded mortices.

OP was speaking of thru mortises, so he'll probably want them
square. I don't think I'd do a rounded mortise unless I was
going to do a very long tenon, and put a peg thru it on the
outside.

> You could do the whole thing by hand as
> John explained (there are special, longer mortising chisels for that
> purpose).

I think it was actually Scott who suggested a mortise chisel.
Cutting mortises that way takes a fair bit of practice.

While all the methods you list are good, for someone starting
out with limited tools I would go with either a router and
template, or drilling a sequence of holes, and in either case
using a normal bench chisel to clean up.

John

JM

John McCoy

in reply to Greg Guarino on 13/03/2015 11:47 AM

16/03/2015 5:02 PM

Greg Guarino <[email protected]> wrote in
news:[email protected]:


> Well I'd probably never have thought of that. But for the uninitiated,
> what's the advantage over the traditional tenon? Just that the rounded
> mortises are easier to make, I assume?

That would be what I'd say. You can cut the mortise with
a router, or by drilling the ends and a series of in-between
holes on the drill press (and chop out the bits between with
a chisel). Either of those are available to someone just
starting in woodworking, who wouldn't have a mortising
machine, mortising attachment for the drill press, or old
style mortise chisel.

The disadvantage is that it's obviously machine-made. If
the tenon is visible, and you want to emphasis your hand-
craftsmanship, then it has to be square. So you either
make a square mortise, or you do as Leon suggests and make
a faux tenon as a trim piece (which, honestly, to me sounds
like more work than making the mortise & tenon square).

John

Sk

Swingman

in reply to Greg Guarino on 13/03/2015 11:47 AM

16/03/2015 12:58 PM

On 3/16/2015 9:01 AM, Greg Guarino wrote:

> Karl's drawing shows a loose tenon that does need to be inset in a
> mortise that is squared off, at least to a certain depth.

Nope, You don't need to do that all.

As I said, I just do it that way on occasion.

--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)

sS

[email protected] (Scott Lurndal)

in reply to Greg Guarino on 13/03/2015 11:47 AM

13/03/2015 5:34 PM

Greg Guarino <[email protected]> writes:
>I'm between projects at the moment and I'm contemplating the next one. I
>try to design in a new technique here and there to improve my skills.
>I've been flirting with the idea of through tenons. Given that I have
>yet to make even a blind mortise and tenon joint, this may be premature,
>but I'm tossing around ideas in my head.
>
>I've got some ideas about how I could make tenons given my limited tool

For tenons, you can't beat a sharp backsaw and a shoulder plane.

>set, and I figure a plunge router (which I don't have yet) and a
>template would take care of a *rounded* mortise. I'm wondering how you
>guys square off the mortise. I assume that unless you have a dedicated
>mortising machine, you use some sort of chisel(s), but what kind?

A mortising chisel is both necessary and sufficient.

Mortising chisels are much beefier than standard bench
or beveled chisels (they're designed to pry the chips out
of the mortise).

dd

"dadiOH"

in reply to Greg Guarino on 13/03/2015 11:47 AM

13/03/2015 1:45 PM

Greg Guarino wrote:
> I'm between projects at the moment and I'm contemplating the next
> one. I try to design in a new technique here and there to improve my
> skills. I've been flirting with the idea of through tenons. Given
> that I have yet to make even a blind mortise and tenon joint, this
> may be premature, but I'm tossing around ideas in my head.
>
> I've got some ideas about how I could make tenons given my limited
> tool set, and I figure a plunge router (which I don't have yet) and a
> template would take care of a *rounded* mortise. I'm wondering how you
> guys square off the mortise. I assume that unless you have a dedicated
> mortising machine, you use some sort of chisel(s), but what kind?
>
> Do you use anything special, or just regular chisels? I've seen a
> corner chisel, if that's the right term. I don't mean the kind they
> sell for hinge mortises. It's a fairly long chisel with two cutting
> edges at a right angle. I also see square chisels, which look very
> much like the hollow chisels that are used in dedicated mortising
> machines, but with a handle to be struck with a mallet. Lastly, I've
> seen mortising chisels, which seem to be twice as thick as regular
> chisels.
> Thoughts?

Step #1
Decide whether you want square corner or rounded mortices.

Step #2
Cut the mortices.
If round, a plunge router works fine. Cut the tenon square, use 1/4 round
router bits to round off tenon edges. You can't use the router to get all
the way to the shoulder but what remains can be done by hand easily with a
knife, rasp, whatever. You could also use loose tenons, easiest of all.
Size the tenons according to the 1/4 round over bits available; i.e., if
tenons are 1/2" thick, use 1/4 radius bit; if 3/4" thick, use 3/8" bit; etc.

If square, you can remove most with a drill bit or router, squaring up with
a hand chisel, knife or file. You could also saw out the corners with a
scroll or coping saw. You could do the whole thing by hand as John
explained (there are special, longer mortising chisels for that purpose).
You could drill them square in a drill press with mortising bits...those are
a bit in a hollow chisel...the bit removes most, the chisel shears off the
corners as you lower the bit, same as a dedicated mortising machine. On a
drill press, you need a fence and a mortising attachment to hold the work
solidly in place.

--

dadiOH
____________________________

Winters getting colder? Tired of the rat race?
Taxes out of hand? Maybe just ready for a change?
Check it out... http://www.floridaloghouse.net

GG

Greg Guarino

in reply to Greg Guarino on 13/03/2015 11:47 AM

15/03/2015 7:37 PM

On 3/14/2015 12:12 PM, Swingman wrote:
> On 3/13/2015 10:47 AM, Greg Guarino wrote:
>> I'm between projects at the moment and I'm contemplating the next one. I
>> try to design in a new technique here and there to improve my skills.
>> I've been flirting with the idea of through tenons. Given that I have
>> yet to make even a blind mortise and tenon joint, this may be premature,
>> but I'm tossing around ideas in my head.
>
>> Thoughts?
>
> Something else to think about if you want to do floating tenons with a
> router.
>
> It's possible to do floating through tenons, with the visible part
> square, giving you a traditional through tenon look.
>
> Because I use a Multi-Router for most of my floating tenon joinery, I've
> done this a few times:
>
> https://picasaweb.google.com/111355467778981859077/EWoodShopJigsFixturesMethods?noredirect=1#6126118837123706546
>
>
> In the one shown I did inset the square part in the stile/leg using a
> dedicated mortising machine for a shallow (1/4") square mortise, but you
> don't have to.
>
> Just make the visible square part of the tenon long enough for the look
> you want, insert in both parts, glue and pin the joint with a
> contrasting pin, and Bob's your uncle.
>
> The part is that difficult to make once you get started, and there is
> more than one way to skin the cat to fabricate them.
>
> I make them square, then round-over the square edges of the floating
> tenon with a pattern makers file to fit the round mortises cut in the
> stock with the Multi-Router.
>
> Traditional look and strength, modern tools...
>
Well I'd probably never have thought of that. But for the uninitiated,
what's the advantage over the traditional tenon? Just that the rounded
mortises are easier to make, I assume?

---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com

GG

Greg Guarino

in reply to Greg Guarino on 13/03/2015 11:47 AM

16/03/2015 10:01 AM

On 3/16/2015 9:50 AM, Leon wrote:
> On 3/15/2015 6:37 PM, Greg Guarino wrote:
>> On 3/14/2015 12:12 PM, Swingman wrote:
>>> On 3/13/2015 10:47 AM, Greg Guarino wrote:
>>>> I'm between projects at the moment and I'm contemplating the next
>>>> one. I
>>>> try to design in a new technique here and there to improve my skills.
>>>> I've been flirting with the idea of through tenons. Given that I have
>>>> yet to make even a blind mortise and tenon joint, this may be
>>>> premature,
>>>> but I'm tossing around ideas in my head.
>>>
>>>> Thoughts?
>>>
>>> Something else to think about if you want to do floating tenons with a
>>> router.
>>>
>>> It's possible to do floating through tenons, with the visible part
>>> square, giving you a traditional through tenon look.
>>>
>>> Because I use a Multi-Router for most of my floating tenon joinery, I've
>>> done this a few times:
>>>
>>> https://picasaweb.google.com/111355467778981859077/EWoodShopJigsFixturesMethods?noredirect=1#6126118837123706546
>>>
>>>
>>>
>>>
>>> In the one shown I did inset the square part in the stile/leg using a
>>> dedicated mortising machine for a shallow (1/4") square mortise, but you
>>> don't have to.
>>>
>>> Just make the visible square part of the tenon long enough for the look
>>> you want, insert in both parts, glue and pin the joint with a
>>> contrasting pin, and Bob's your uncle.
>>>
>>> The part is that difficult to make once you get started, and there is
>>> more than one way to skin the cat to fabricate them.
>>>
>>> I make them square, then round-over the square edges of the floating
>>> tenon with a pattern makers file to fit the round mortises cut in the
>>> stock with the Multi-Router.
>>>
>>> Traditional look and strength, modern tools...
>>>
>> Well I'd probably never have thought of that. But for the uninitiated,
>> what's the advantage over the traditional tenon? Just that the rounded
>> mortises are easier to make, I assume?
>
> Absolutely and the over sized square portion that is visible does not
> have to fit into a mortise.

I was thinking about that. Karl's drawing shows a loose tenon that does
need to be inset in a mortise that is squared off, at least to a certain
depth. I see that you could do away with that, by making the "square"
part only as thick as the visible section. But it strikes me that that
would make for a very thin edge, unless the visible section is to be
thicker than usual.

Ll

Leon

in reply to Greg Guarino on 13/03/2015 11:47 AM

15/03/2015 2:04 PM

On 3/14/2015 11:12 AM, Swingman wrote:
> On 3/13/2015 10:47 AM, Greg Guarino wrote:
>> I'm between projects at the moment and I'm contemplating the next one. I
>> try to design in a new technique here and there to improve my skills.
>> I've been flirting with the idea of through tenons. Given that I have
>> yet to make even a blind mortise and tenon joint, this may be premature,
>> but I'm tossing around ideas in my head.
>
>> Thoughts?
>
> Something else to think about if you want to do floating tenons with a
> router.
>
> It's possible to do floating through tenons, with the visible part
> square, giving you a traditional through tenon look.

AND to expand on that a bit.... you can also do trough tenons and sand
them flush with the piece that they are going through, the exposed side.
Don't worry about appearance. Cut a false tenon to glue over the
actual flush sanded through tenon. It can be slightly larger than the
actual mortise to cover the "real" joint lines.




>
> Because I use a Multi-Router for most of my floating tenon joinery, I've
> done this a few times:
>
> https://picasaweb.google.com/111355467778981859077/EWoodShopJigsFixturesMethods?noredirect=1#6126118837123706546
>
Great idea! And affords the sticking out portion of the tenon to be a
longer length than my suggestion above.





> In the one shown I did inset the square part in the stile/leg using a
> dedicated mortising machine for a shallow (1/4") square mortise, but you
> don't have to.
>
> Just make the visible square part of the tenon long enough for the look
> you want, insert in both parts, glue and pin the joint with a
> contrasting pin, and Bob's your uncle.
>
> The part is that difficult to make once you get started, and there is
> more than one way to skin the cat to fabricate them.
>
> I make them square, then round-over the square edges of the floating
> tenon with a pattern makers file to fit the round mortises cut in the
> stock with the Multi-Router.
>
> Traditional look and strength, modern tools...
>

Sk

Swingman

in reply to Greg Guarino on 13/03/2015 11:47 AM

14/03/2015 11:12 AM

On 3/13/2015 10:47 AM, Greg Guarino wrote:
> I'm between projects at the moment and I'm contemplating the next one. I
> try to design in a new technique here and there to improve my skills.
> I've been flirting with the idea of through tenons. Given that I have
> yet to make even a blind mortise and tenon joint, this may be premature,
> but I'm tossing around ideas in my head.

> Thoughts?

Something else to think about if you want to do floating tenons with a
router.

It's possible to do floating through tenons, with the visible part
square, giving you a traditional through tenon look.

Because I use a Multi-Router for most of my floating tenon joinery, I've
done this a few times:

https://picasaweb.google.com/111355467778981859077/EWoodShopJigsFixturesMethods?noredirect=1#6126118837123706546

In the one shown I did inset the square part in the stile/leg using a
dedicated mortising machine for a shallow (1/4") square mortise, but you
don't have to.

Just make the visible square part of the tenon long enough for the look
you want, insert in both parts, glue and pin the joint with a
contrasting pin, and Bob's your uncle.

The part is that difficult to make once you get started, and there is
more than one way to skin the cat to fabricate them.

I make them square, then round-over the square edges of the floating
tenon with a pattern makers file to fit the round mortises cut in the
stock with the Multi-Router.

Traditional look and strength, modern tools...

--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)


You’ve reached the end of replies