"G Mulcaster" <[email protected]> wrote in message
news:[email protected]...
> Hi folks,
>
> I have a Makita 2030 Planer-Jointer and the jointer infeed table needs
> adjusting.
>
> Does anyone know how to adjust these? No luck at the Makita manuals
> download site.
>
> Thanks for any help.
>
> Regards, Gary
The site has the 2030N manual
http://www.makita.com/assets_product/2030N/owners_manuals/2030N.pdf
and it shows the adjustment knob in Fig 27 and on the parts breakdown on
page 23. Look for some kind of screw lock for the infeed table height
adjustment - most jointers have some sort of locking device on that
adjustment.
Bob S.
> Bob,
>
> Thanks for the reply. Yes, the fig 27 and page 23 knob is for
> adjusting the infeed bed for depth of cut. No problem there.
>
> My question was poorly worded.
>
> The problem is one of alignment of the infeed and outfeed beds. The
> infeed bed has a 1/32" sag at the entry end. That is, if I bring the
> beds to zero cut and place a straight edge on the beds, a gap is
> visible at the end of the entry bed farthest from the cutters. As a
> result, the wood being jointed develops a convex curve.
>
> I'm looking for a way to adust the alignment so both beds are exactly
> parallel with each other.
>
> Regards, Gary
Gary,
The site and the manual do not show the alignment procedures that I can see,
so..... Tear into it and remove the infeed table. See if you can find any
adjustments and if not, then you have to use the practice that is typically
used on jointers - adding shims on the slides that the infeed table rests
on. Other than that - call the company and ask.
Bob S.
hi Gary, i'm having exactly the same problem with my 2030 and it's not weather as it's pretty stable here in northern CA. looks like you went through this with a fine tooth comb. so sharpened blades did it eh? i'll try that, thanks for posting all this.
...a also have an old Sears jointer and had the same problem but it does have adjustment screws for this very thing and now it's running perfectly flat
seems odd to me that this Makita doesn't have the same
thanks again
Bernie
>>>>
>>>> I have a Makita 2030 Planer-Jointer and the jointer infeed table needs
>>>> adjusting.
>>>>
>>>> Does anyone know how to adjust these? No luck at the Makita manuals
>>>> download site.
>>>>
>>>> Thanks for any help.
>>>>
>On a 29 inch long infeed table that might not be a lot. Is there any
>chance there is a technique issue or maybe blades too proud?
Just checked. Blades are level with the outfeed table. That is, if I
place the two pieces of teak on the rear bed, the cutters barely touch
the teak. Ditto if I raise the infeed table level with the outfeed
table. When the pieces lay across both beds, the cutters barely
touch them.
Looking
>at my Makita I see no adjustment. Unless the jointer really got wacked
>I would suspect it was dead on from the factory. I do not have a
>certified straight edge but my 6' level show no problems on my Makita
>2030.
The 2030 is quite old, and has been dead on until this year. (An
exception noted below).
>Are you ignoring the pointer on the jointer and testing this with a
>known good straight edge at least 5 feet long? That pointer adjusts.
>Are you sayin when you place a 6 foot straghtedge on both beds and
>crank the infeed up to even with the outfeed by the cutter that 29"
>from the cutter you observe a 1/32" gap?
Yes. I use a 6' straight edge. When I lay it on the tables, the
straightedge is flush with the whole length of the outfeed table. It
contacts the cutter end of the infeed table and a 1/32" gap shows at
the other end of the infeed table.
>
>If the infeed table is caddywompus there are 4 bolt underneath that
>may allow for minor shifting to adjust a twisted infeed table. You
>need an anti-caddywompus guage though.
Can't find the bolts - nor do I see them in the manual (2030N).
>How about a picture?
I don't think the gap will show.
I'm thinking it might be a temperature problem. I now recall having
the same issue last Winter when I once tried to use it in my unheated
garage. During the following Summer there was no problem. This year
my garage is heated and I'm now in there often. Since I only have the
heat on during the day, the machine (which is a big chunk of metal
subject to heating/cooling effects) may not warm up enough. We have
some warm weather on the way to check my theory.
Thanks for taking the time to respond.
Gary
On Mon, 7 Apr 2008 20:20:01 -0400, "BobS" <[email protected]> wrote:
>
>"G Mulcaster" <[email protected]> wrote in message
>news:[email protected]...
>> Hi folks,
>>
>> I have a Makita 2030 Planer-Jointer and the jointer infeed table needs
>> adjusting.
>>
>> Does anyone know how to adjust these? No luck at the Makita manuals
>> download site.
>>
>> Thanks for any help.
>>
>> Regards, Gary
Just a follow up.
I never did get the infeed table adjusted; it still sags about 1/32"
at the infeed end.
However, at long last I had the blades sharpened. Now, finally, the
jointer works perfectly with no convexing (new woodworking term) of
the boards.
I love my Makita 2030 again :)
Gary
On Tue, 8 Apr 2008 13:17:33 -0400, "BobS" <[email protected]> wrote:
>
>> Bob,
>>
>> Thanks for the reply. Yes, the fig 27 and page 23 knob is for
>> adjusting the infeed bed for depth of cut. No problem there.
>>
>> My question was poorly worded.
>>
>> The problem is one of alignment of the infeed and outfeed beds. The
>> infeed bed has a 1/32" sag at the entry end. That is, if I bring the
>> beds to zero cut and place a straight edge on the beds, a gap is
>> visible at the end of the entry bed farthest from the cutters. As a
>> result, the wood being jointed develops a convex curve.
>>
>> I'm looking for a way to adust the alignment so both beds are exactly
>> parallel with each other.
>>
>> Regards, Gary
>
>Gary,
>
>The site and the manual do not show the alignment procedures that I can see,
>so..... Tear into it and remove the infeed table. See if you can find any
>adjustments and if not, then you have to use the practice that is typically
>used on jointers - adding shims on the slides that the infeed table rests
>on. Other than that - call the company and ask.
>>
Bob,
I removed the infeed table. No adjustments found, However, it looks
to be easy to install shims. I will look into that.
There are three Makita service outlets nearby. I'll see if what they
have to say. They may have shimstock handy.
I called the National Call Center. Closed now, will try tomorrow.
Again, thanks for the help.
Gary
On Thu, 10 Apr 2008 02:30:50 GMT, G Mulcaster
<[email protected]> wrote:
>>>>>
>>>>> I have a Makita 2030 Planer-Jointer and the jointer infeed table needs
>>>>> adjusting.
>>>>>
>>>>> Does anyone know how to adjust these? No luck at the Makita manuals
>>>>> download site.
>>>>>
>>>>> Thanks for any help.
>>>>>
>
>>On a 29 inch long infeed table that might not be a lot. Is there any
>>chance there is a technique issue or maybe blades too proud?
>
>Just checked. Blades are level with the outfeed table. That is, if I
>place the two pieces of teak on the rear bed, the cutters barely touch
>the teak. Ditto if I raise the infeed table level with the outfeed
>table. When the pieces lay across both beds, the cutters barely
>touch them.
>
> Looking
>>at my Makita I see no adjustment. Unless the jointer really got wacked
>>I would suspect it was dead on from the factory. I do not have a
>>certified straight edge but my 6' level show no problems on my Makita
>>2030.
>
>The 2030 is quite old, and has been dead on until this year. (An
>exception noted below).
>
>>Are you ignoring the pointer on the jointer and testing this with a
>>known good straight edge at least 5 feet long? That pointer adjusts.
>>Are you sayin when you place a 6 foot straghtedge on both beds and
>>crank the infeed up to even with the outfeed by the cutter that 29"
>>from the cutter you observe a 1/32" gap?
>
>Yes. I use a 6' straight edge. When I lay it on the tables, the
>straightedge is flush with the whole length of the outfeed table. It
>contacts the cutter end of the infeed table and a 1/32" gap shows at
>the other end of the infeed table.
>>
>>If the infeed table is caddywompus there are 4 bolt underneath that
>>may allow for minor shifting to adjust a twisted infeed table. You
>>need an anti-caddywompus guage though.
>
>Can't find the bolts - nor do I see them in the manual (2030N).
>
>>How about a picture?
>
>I don't think the gap will show.
>
>I'm thinking it might be a temperature problem. I now recall having
>the same issue last Winter when I once tried to use it in my unheated
>garage. During the following Summer there was no problem. This year
>my garage is heated and I'm now in there often. Since I only have the
>heat on during the day, the machine (which is a big chunk of metal
>subject to heating/cooling effects) may not warm up enough. We have
>some warm weather on the way to check my theory.
>
>Thanks for taking the time to respond.
>
>Gary
I looked at those 4 bolts. They bolt the infeed table to a surface
parallel to the slope the infeed table slides up and down. I guess
those bolts would do nothing about alignment. The 2030 now in my
basement I have used on occasion since about 1990. It has always been
in a stable environment generally ranging from 72-78 degrees with
little temperature fluctuation.
Well you have a stumper and maybe temperature is having an effect.
On Wed, 09 Apr 2008 23:28:46 -0400, Jim Behning
<[email protected]> wrote:
>On Thu, 10 Apr 2008 02:30:50 GMT, G Mulcaster
><[email protected]> wrote:
>
>>>>>>
>>>>>> I have a Makita 2030 Planer-Jointer and the jointer infeed table needs
>>>>>> adjusting.
>>>>>>
>>>>>> Does anyone know how to adjust these? No luck at the Makita manuals
>>>>>> download site.
>>>>>>
>>>>>> Thanks for any help.
>>>>>>
>>
>>>On a 29 inch long infeed table that might not be a lot. Is there any
>>>chance there is a technique issue or maybe blades too proud?
>>
>>Just checked. Blades are level with the outfeed table. That is, if I
>>place the two pieces of teak on the rear bed, the cutters barely touch
>>the teak. Ditto if I raise the infeed table level with the outfeed
>>table. When the pieces lay across both beds, the cutters barely
>>touch them.
>>
>> Looking
>>>at my Makita I see no adjustment. Unless the jointer really got wacked
>>>I would suspect it was dead on from the factory. I do not have a
>>>certified straight edge but my 6' level show no problems on my Makita
>>>2030.
>>
>>The 2030 is quite old, and has been dead on until this year. (An
>>exception noted below).
>>
>>>Are you ignoring the pointer on the jointer and testing this with a
>>>known good straight edge at least 5 feet long? That pointer adjusts.
>>>Are you sayin when you place a 6 foot straghtedge on both beds and
>>>crank the infeed up to even with the outfeed by the cutter that 29"
>>>from the cutter you observe a 1/32" gap?
>>
>>Yes. I use a 6' straight edge. When I lay it on the tables, the
>>straightedge is flush with the whole length of the outfeed table. It
>>contacts the cutter end of the infeed table and a 1/32" gap shows at
>>the other end of the infeed table.
>>>
>>>If the infeed table is caddywompus there are 4 bolt underneath that
>>>may allow for minor shifting to adjust a twisted infeed table. You
>>>need an anti-caddywompus guage though.
>>
>>Can't find the bolts - nor do I see them in the manual (2030N).
>>
>>>How about a picture?
>>
>>I don't think the gap will show.
>>
>>I'm thinking it might be a temperature problem. I now recall having
>>the same issue last Winter when I once tried to use it in my unheated
>>garage. During the following Summer there was no problem. This year
>>my garage is heated and I'm now in there often. Since I only have the
>>heat on during the day, the machine (which is a big chunk of metal
>>subject to heating/cooling effects) may not warm up enough. We have
>>some warm weather on the way to check my theory.
>>
>>Thanks for taking the time to respond.
>>
>>Gary
>I looked at those 4 bolts. They bolt the infeed table to a surface
>parallel to the slope the infeed table slides up and down. I guess
>those bolts would do nothing about alignment.
Hmm. I seem to have one large spring loaded bolt holding the infeed
table on the sloped rails. The rails are fluted (?) to ensure the
infeed table stays in lateral alignment.
The 2030 now in my
>basement I have used on occasion since about 1990. It has always been
>in a stable environment generally ranging from 72-78 degrees with
>little temperature fluctuation.
>
>Well you have a stumper and maybe temperature is having an effect.
Will know soon. Warm weather enroute :)
Regards, Gary
On Mon, 7 Apr 2008 20:20:01 -0400, "BobS" <[email protected]> wrote:
>
>"G Mulcaster" <[email protected]> wrote in message
>news:[email protected]...
>> Hi folks,
>>
>> I have a Makita 2030 Planer-Jointer and the jointer infeed table needs
>> adjusting.
>>
>> Does anyone know how to adjust these? No luck at the Makita manuals
>> download site.
>>
>> Thanks for any help.
>>
>> Regards, Gary
>
>The site has the 2030N manual
>
>http://www.makita.com/assets_product/2030N/owners_manuals/2030N.pdf
>
>and it shows the adjustment knob in Fig 27 and on the parts breakdown on
>page 23. Look for some kind of screw lock for the infeed table height
>adjustment - most jointers have some sort of locking device on that
>adjustment.
Bob,
Thanks for the reply. Yes, the fig 27 and page 23 knob is for
adjusting the infeed bed for depth of cut. No problem there.
My question was poorly worded.
The problem is one of alignment of the infeed and outfeed beds. The
infeed bed has a 1/32" sag at the entry end. That is, if I bring the
beds to zero cut and place a straight edge on the beds, a gap is
visible at the end of the entry bed farthest from the cutters. As a
result, the wood being jointed develops a convex curve.
I'm looking for a way to adust the alignment so both beds are exactly
parallel with each other.
Regards, Gary
On Tue, 08 Apr 2008 03:05:21 GMT, G Mulcaster
<[email protected]> wrote:
>On Mon, 7 Apr 2008 20:20:01 -0400, "BobS" <[email protected]> wrote:
>
>>
>>"G Mulcaster" <[email protected]> wrote in message
>>news:[email protected]...
>>> Hi folks,
>>>
>>> I have a Makita 2030 Planer-Jointer and the jointer infeed table needs
>>> adjusting.
>>>
>>> Does anyone know how to adjust these? No luck at the Makita manuals
>>> download site.
>>>
>>> Thanks for any help.
>>>
>>> Regards, Gary
>>
>>The site has the 2030N manual
>>
>>http://www.makita.com/assets_product/2030N/owners_manuals/2030N.pdf
>>
>>and it shows the adjustment knob in Fig 27 and on the parts breakdown on
>>page 23. Look for some kind of screw lock for the infeed table height
>>adjustment - most jointers have some sort of locking device on that
>>adjustment.
>
>Bob,
>
>Thanks for the reply. Yes, the fig 27 and page 23 knob is for
>adjusting the infeed bed for depth of cut. No problem there.
>
>My question was poorly worded.
>
>The problem is one of alignment of the infeed and outfeed beds. The
>infeed bed has a 1/32" sag at the entry end. That is, if I bring the
>beds to zero cut and place a straight edge on the beds, a gap is
>visible at the end of the entry bed farthest from the cutters. As a
>result, the wood being jointed develops a convex curve.
>
>I'm looking for a way to adust the alignment so both beds are exactly
>parallel with each other.
>
>Regards, Ga
On a 29 inch long infeed table that might not be a lot. Is there any
chance there is a technique issue or maybe blades too proud? Looking
at my Makita I see no adjustment. Unless the jointer really got wacked
I would suspect it was dead on from the factory. I do not have a
certified straight edge but my 6' level show no problems on my Makita
2030.
Are you ignoring the pointer on the jointer and testing this with a
known good straight edge at least 5 feet long? That pointer adjusts.
Are you sayin when you place a 6 foot straghtedge on both beds and
crank the infeed up to even with the outfeed by the cutter that 29"
from the cutter you observe a 1/32" gap?
If the infeed table is caddywompus there are 4 bolt underneath that
may allow for minor shifting to adjust a twisted infeed table. You
need an anti-caddywompus guage though.
How about a picture?