interesting book and fun to read
https://archive.org/details/scribnerslumberl00scri
SCRIBNER'S LUMBER & LOG BOOK
FOR SHIP AND BOAT BUILDERS, LUMBER
MERCHANTS, SAW-MILL MEN, FARMERS AND MECHANICS.
BEING A CORRECT MEASUREMENT OF SCANTLING, BOARDS, PLANK,
CUBICAL CONTENTS OF SQUARE AND ROUND TIMBER,
one of my favorite from the front pages
"Among the vast number of recommendations
of this book which we have received from time
to time, we think it unnecessary to insert any
here, as the book is too well known to require
their publication. The popularity of the book
is seen by its immense sales. "
On 8/17/2015 9:28 PM, Electric Comet wrote:
> On Mon, 17 Aug 2015 12:34:50 -0700
> Electric Comet <[email protected]> wrote:
>
>> interesting book and fun to read
>
> complete this sentence
>
> "Hard wood stumps decay in five to six years; spruce
> stumps decay in about the same time; hemlock stumps
> in eight to nine years; cedar eight to nine years; pine
> stumps,_______________"
>
Southern Yellow or White Pine?
Electric Comet <[email protected]> wrote in news:mqu59u$9em$1
@dont-email.me:
> On Mon, 17 Aug 2015 12:34:50 -0700
> Electric Comet <[email protected]> wrote:
>
>> interesting book and fun to read
>
> complete this sentence
>
> "Hard wood stumps decay in five to six years; spruce
> stumps decay in about the same time; hemlock stumps
> in eight to nine years; cedar eight to nine years; pine
> stumps,_______________"
>
even the most dilligent researcher.
:-)
Puckdropper
--
Make it to fit, don't make it fit.
On 8/19/2015 5:48 PM, Electric Comet wrote:
> On Mon, 17 Aug 2015 12:34:50 -0700
> Electric Comet <[email protected]> wrote:
>
>> interesting book and fun to read
>
> another interesting one
> they provide a table of circular saw speeds
>
> formula for determining the rpm of the rim of a circular saw blade
> 9000/((2*Pi*r)/12)
I had to dig into this.. ;~)
I'll assume that 9000 feet per minute is the "ideal" linear speed for
cutting wood. Basically a tad over 100 mph. And that the formula is
to determine how fast the any sized blade needs to turn to cut at the
ideal speed. FWIW RPM at the rim is the same as it is at the arbor. I
think you probably meant to RPM of the blade so that the rim speed is
correct.
I use a slightly simpler formula. 9000/((3.14*d)/12)
>
> it is pretty close for my 7 1/4 skilsaw which is rated at 5300 noload rpm
> the formula gives 4741 rpm
>
On Mon, 17 Aug 2015 12:34:50 -0700
Electric Comet <[email protected]> wrote:
> interesting book and fun to read
complete this sentence
"Hard wood stumps decay in five to six years; spruce
stumps decay in about the same time; hemlock stumps
in eight to nine years; cedar eight to nine years; pine
stumps,_______________"
On Mon, 17 Aug 2015 12:34:50 -0700
Electric Comet <[email protected]> wrote:
> interesting book and fun to read
boil wooden pulleys in olive oil for eight minutes to make them as hard as
copper after they dry
On Mon, 17 Aug 2015 12:34:50 -0700
Electric Comet <[email protected]> wrote:
> interesting book and fun to read
another interesting one
they provide a table of circular saw speeds
formula for determining the rpm of the rim of a circular saw blade
9000/((2*Pi*r)/12)
it is pretty close for my 7 1/4 skilsaw which is rated at 5300 noload rpm
the formula gives 4741 rpm
On 8/17/2015 10:15 PM, Electric Comet wrote:
> On Mon, 17 Aug 2015 12:34:50 -0700
> Electric Comet <[email protected]> wrote:
>
>> interesting book and fun to read
>
> boil wooden pulleys in olive oil for eight minutes to make them as hard as
> copper after they dry
Well depending on the wood, that could either make them harder or
sifter. Copper is pretty soft.