Mon, Sep 15, 2003, 5:15pm [email protected]
([email protected]) asks:
I've looked at the plans for a table saw outfeed table in an old
ShopNotes. Are there any other plans on the Net that you folks would
recommend?
Something even simpler. You got a kid? Anywhere from about 8 yo,
up? That's all you need. My grandfather would rip lumber and plywood,
and I would act as an outfeed table/handler. No prob
JOAT
Atheism is a non-prophet organization.
Life just ain't life without good music. - JOAT
Web Page Update 15 Sep 2003. Some tunes I like.
http://community-2.webtv.net/Jakofalltrades/SOMETUNESILIKE/
Jack-of-all-trades - JOAT wrote:
> Something even simpler. You got a kid? Anywhere from about 8
> yo, up? That's all you need. My grandfather would rip lumber and
> plywood, and I would act as an outfeed table/handler. No prob
2 or 3 times I've tried this. Despite my instructions, "Don't pull, just
hold, especially don't put sideways pressure" the results were suboptimal.
The last time my SWMBO helped the cut ended up with a noticable curve -- a
good trick for a table saw & rip fence. I thanked her for her help,
jury-rigged an outfeed support for that sawing session, & dropped $20 on my
next trip to the Borg on an outfeed roller. Much better results.
I dunno, maybe my helpers just wanted to see what kickback looks like...
;-)
-- Mark
"B a r r y B u r k e J r ." <[email protected]> wrote
in message news:[email protected]...
> On Mon, 15 Sep 2003 17:15:19 -0400, "Dennis [email protected]"
> <[email protected]> wrote:
>
> >I've looked at the plans for a table saw outfeed table
> >in an old ShopNotes. Are there any other plans on
> >the Net that you folks would recommend?
> >
> >Dennis Vogel
> >
>
> What kind of saw, contractor, cabinet, portable?
Forgot--Delta contractor.
> My very basic contractor's saw out feed table is simply two notched
> arms that attach with long versions of the bolts that hold the wings
> on. It's covered with laminate scraps left over from my router table
> project. I left a gap to allow my fence to slide between the saw
> table and the out feed table.
>
> It's simple and pops off with 4 bolts and a 17mm socket.
That sounds similar to the plans I saw.
Dennis Vogel
"dteckie" <[email protected]> wrote in message
news:[email protected]...
> "Dennis [email protected]" <[email protected]> wrote in message
news:<[email protected]>...
> > Looks good. Thanks.
> >
> > Man, is your saw ever clean! ;-)
> >
> > Dennis Vogel
> >
> > "Ed. O." <[email protected]> wrote in message
> > news:[email protected]...
> > > Dennis,
> > > You don't need plans, check out a few pictures and make it fit your
saw.
> > > You can check out the one I built at:
> > > http://www.amiigas.com/outfeed/outfeed.htm
>
> Very Nice Table and projects Dennis.
Uh, wish I could take credit for that but it was Ed. O.
that sent that. Look above at the attribution. I was
just the addressee.
Dennis Vogel
"Ed. O." <[email protected]> wrote in message
news:[email protected]...
> Dennis,
> It is only clean during picture taking time.
Hah. Now I feel better about my shop.
I better not let SWMBO see your pics!
Dennis Vogel
"Chris Merrill" <[email protected]> wrote in message
news:[email protected]...
> Ed. O. wrote:
> > You don't need plans, check out a few pictures and make it fit your
saw.
> > You can check out the one I built at:
> > http://www.amiigas.com/outfeed/outfeed.htm
>
> While your table is very nice...maybe he does _need_
> plans...which is, no doubt, why he asked for them.
Nah, take it easy on him, he's right. "Plans" was probably
not the right word. A few good photos and rough sizes
is usually good enough for most things. The photos have
been pretty good. Sometimes a parts list is good for
hidden or specialized hardware but for a OF table, I
think I can go from the photos. Most variations seem
to be how the table is attached to the saw.
Dennis Vogel
"Todd Seidenberg" <[email protected]> wrote in message
news:[email protected]...
> Hi,
>
> there's a very nice plan for an outfeed table in this:
>
> http://woodstore.woodmall.com/bewoso.html
>
> (I bought this mag for the drill press table plans in it. )
>
> Hope this helps,
Yep. Thanks. I wish they had a few pics so I could
see what I was buying.
Dennis Vogel
"Jack-of-all-trades - JOAT" <[email protected]> wrote in message
news:[email protected]...
Mon, Sep 15, 2003, 5:15pm [email protected]
(Dennis [email protected]) asks:
I've looked at the plans for a table saw outfeed table in an old
ShopNotes. Are there any other plans on the Net that you folks would
recommend?
Something even simpler. You got a kid? Anywhere from about 8 yo,
up? That's all you need. My grandfather would rip lumber and plywood,
and I would act as an outfeed table/handler. No prob
Great idea. When can your kid or grandfather
come over and help out? Tomorrow morning OK?
As you may have guessed from the original request
I've got no kids, fathers, or grandfathers around to help.
It's just me. That's why I need an outfeed table.
Dennis Vogel
Hi,
there's a very nice plan for an outfeed table in this:
http://woodstore.woodmall.com/bewoso.html
(I bought this mag for the drill press table plans in it. )
Hope this helps,
Todd
"Ed. O." <[email protected]> wrote in message news:<[email protected]>...
> Dennis,
> You don't need plans, check out a few pictures and make it fit your saw.
> You can check out the one I built at:
> http://www.amiigas.com/outfeed/outfeed.htm
"Dennis [email protected]" <[email protected]> wrote in message news:<[email protected]>...
> Looks good. Thanks.
>
> Man, is your saw ever clean! ;-)
>
> Dennis Vogel
>
> "Ed. O." <[email protected]> wrote in message
> news:[email protected]...
> > Dennis,
> > You don't need plans, check out a few pictures and make it fit your saw.
> > You can check out the one I built at:
> > http://www.amiigas.com/outfeed/outfeed.htm
Very Nice Table and projects Dennis.
Look at these two sites:
http://members.aol.com/Alamaral/Outfeed.html
http://www.sawsndust.com/p-outfeed.htm
I built an outfeed for my Unisaw, which was sort of a hybrid of the above
two approaches. You can see some pics of my effort here:
http://pages.cthome.net/logmanworld/outfeed1.jpg
http://pages.cthome.net/logmanworld/outfeed4.jpg
http://pages.cthome.net/logmanworld/outfeed5.jpg
Mike
"Dennis [email protected]" <[email protected]> wrote in message
news:[email protected]...
> I've looked at the plans for a table saw outfeed table
> in an old ShopNotes. Are there any other plans on
> the Net that you folks would recommend?
>
> Dennis Vogel
>
>
Ed. O. wrote:
> You don't need plans, check out a few pictures and make it fit your saw.
> You can check out the one I built at:
> http://www.amiigas.com/outfeed/outfeed.htm
While your table is very nice...maybe he does _need_
plans...which is, no doubt, why he asked for them.
--
************************************
Chris Merrill
[email protected]
(remove the ZZZ to contact me)
************************************
On Mon, 15 Sep 2003 17:15:19 -0400, "Dennis [email protected]"
<[email protected]> wrote:
>I've looked at the plans for a table saw outfeed table
>in an old ShopNotes. Are there any other plans on
>the Net that you folks would recommend?
>
>Dennis Vogel
>
What kind of saw, contractor, cabinet, portable?
My very basic contractor's saw out feed table is simply two notched
arms that attach with long versions of the bolts that hold the wings
on. It's covered with laminate scraps left over from my router table
project. I left a gap to allow my fence to slide between the saw
table and the out feed table.
It's simple and pops off with 4 bolts and a 17mm socket.
Barry
"Dennis [email protected]" <[email protected]> wrote in message
news:[email protected]...
> I've looked at the plans for a table saw outfeed table
> in an old ShopNotes. Are there any other plans on
> the Net that you folks would recommend?
>
> Dennis Vogel
Plans? I never thought of something that complex. Mine is a piece of
laminate covered plywood. Two outer legs that fold. The side on the saw is
just a support of pine that rests on the rails for the fence. Spring clamps
hold it in place. Rout a slot for the miter.
Took about an hour to make and can be removed/replaced in about 15 seconds.
Fold up the two legs and it takes up little space in a tight shop. Pics if
you want them.
Ed