I recently purchased a Makita cordless drill. This is my first such tool
and have question regarding some of the function switches which are
poorly explained in the instruction booklet.
(Sorry, I don't have the model number handy -- I left the drill at
work.)
There are two switches on the "back" of the drill body which apparently
control the drill's function with regards to the operation being
performed, be it a)drilling or b)driving screws.
See pic: http://www.lawson-his.co.uk/images/Makita/6337dwde.jpg
One is a large thumb actuated switch that has two positions (1 and 2)
that controls the speed. It is located aft of the chuck and is common
to every drill I've seen. Easy enough to understand what that one does.
My question is in regards to the second, smaller switch, which also has two
positions, each identified by a picture: one is a "screw", and the
other is a "drill bit". There is a red locking switch that prevents
this switch (which moves left to right) from being unintentionally moved
from one setting to the other. This switch is located between the
aforementioned speed switch and the "drag" ring aft of the chuck.
The instruction booklet says to set the switch position according to the
operation being performed. Fine. But, it doesn't attempt to explain
what purpose that this serves. To my eyes, I see absolutely NO
DIFFERENCE in the drill's performance, regardless of the setting I
select. I've never seen this type of switch on any other cordless
drill. The salesperson who sold me the tool has no idea what it does.
Neither did the Makita rep I spoke to.
Why must I move this switch to one side when drilling and to the other
when driving screws? No other drill has this built-in time wasting
feature.
What the hell does this switch do??? }:O)
--
DC
(((:~{>
>No other drill has this built-in time wasting
> feature.
Exactly. Carry on using low gear/ high torque for driving screws, high gear/
lower torque for drilling. Better still, leave it in high gear all the time
and buy an impact driver for screwdriving. Is it just me or have Makita gone
downhill lately? Still wouldn't be without my LS1013 chop saw or 3612CX
router though.
"B A R R Y" <[email protected]> wrote in message
news:[email protected]...
> Leon wrote:
>>
>>
>> I use this feature all the time. Much easier to flip the switch from
>> drill to screw rather than twist the clutch setting up and down.
>> Especially when using small screws.
>
>
> You guys only use one drill? <G>
>
> I'll usually have one with the drill bit and another with the screwdriver
> bit.
When I am around the shop I may have 3 or 4 drills set up. On location at a
customers house usually 1 drill.
"DC" <[email protected]> wrote in message
news:[email protected]...
does.
>
> My question is in regards to the second, smaller switch, which also has
> two
> positions, each identified by a picture: one is a "screw", and the
> other is a "drill bit". There is a red locking switch that prevents
> this switch (which moves left to right) from being unintentionally moved
> from one setting to the other. This switch is located between the
> aforementioned speed switch and the "drag" ring aft of the chuck.
This is a very useful switch. The drill switch setting is obviously for
drilling but also over rides the clutch. If you are using small screws and
are using a low number clutch setting you will easily strip out the screws
or wood if you use the drill setting. If you use the screw setting to drill
holes the clutch will slip.
In article <[email protected]>,
"deadlock" <nobody@nowhere_yes_its a_cliche.com> wrote:
> Still wouldn't be without my LS1013 chop saw
... that would be bad. A great saw.
"DC" <[email protected]> wrote in message
news:[email protected]...
>I recently purchased a Makita cordless drill. This is my first such tool
> and have question regarding some of the function switches which are
> poorly explained in the instruction booklet.
>
> (Sorry, I don't have the model number handy -- I left the drill at
> work.)
>
> There are two switches on the "back" of the drill body which apparently
> control the drill's function with regards to the operation being
> performed, be it a)drilling or b)driving screws.
>
> See pic: http://www.lawson-his.co.uk/images/Makita/6337dwde.jpg
>
> One is a large thumb actuated switch that has two positions (1 and 2)
> that controls the speed. It is located aft of the chuck and is common
> to every drill I've seen. Easy enough to understand what that one does.
>
> My question is in regards to the second, smaller switch, which also has
> two
> positions, each identified by a picture: one is a "screw", and the
> other is a "drill bit". There is a red locking switch that prevents
> this switch (which moves left to right) from being unintentionally moved
> from one setting to the other. This switch is located between the
> aforementioned speed switch and the "drag" ring aft of the chuck.
>
> The instruction booklet says to set the switch position according to the
> operation being performed. Fine. But, it doesn't attempt to explain
> what purpose that this serves. To my eyes, I see absolutely NO
> DIFFERENCE in the drill's performance, regardless of the setting I
> select. I've never seen this type of switch on any other cordless
> drill. The salesperson who sold me the tool has no idea what it does.
> Neither did the Makita rep I spoke to.
>
> Why must I move this switch to one side when drilling and to the other
> when driving screws? No other drill has this built-in time wasting
> feature.
>
> What the hell does this switch do??? }:O)
>
I would have to guess that the switch is to switch from drilling to screwing
without having to turn the "drag collar" all the way up. My older one has
five "drag" settings plus a drill setting on the collar. To go from driving
with a low setting you have to turn the collar all the way up to the drill
setting. I'm guessing you could leave yours set to(for example) a number 3
for driving and then switch to drilling by moving the one switch.
To test, try setting the collar at a "2" for example, with the switch in
drive mode; now hold the chuck and turn the drill on. The drag clutch should
slip at a fairly low power. Now, without moving the drag collar, change the
button to "drill". If you try holding the chuck now, it should stop the
drill IF you can hold it that tight.
--
Nahmie
The only road to success is always under construction.
"deadlock" <nobody@nowhere_yes_its a_cliche.com> wrote in message
news:[email protected]...
> >No other drill has this built-in time wasting
>> feature.
>
> Exactly. Carry on using low gear/ high torque for driving screws, high
> gear/ lower torque for drilling. Better still, leave it in high gear all
> the time and buy an impact driver for screwdriving. Is it just me or have
> Makita gone downhill lately? Still wouldn't be without my LS1013 chop saw
> or 3612CX router though.
I use this feature all the time. Much easier to flip the switch from drill
to screw rather than twist the clutch setting up and down. Especially when
using small screws.
"Robatoy" <[email protected]> wrote in message
news:[email protected]...
> In article <[email protected]>,
> "deadlock" <nobody@nowhere_yes_its a_cliche.com> wrote:
>
>> Still wouldn't be without my LS1013 chop saw
>
> ... that would be bad. A great saw.
Sure is. Picked up a pair of Bosch 96T Special Alu blades for it last week
on a two for one offer, man those things cut clean.
Norman D. Crow wrote:
> "DC" <[email protected]> wrote in message
> news:[email protected]...
>> My question is in regards to the second, smaller switch, which also has
>> two
>> positions, each identified by a picture: one is a "screw", and the
>> other is a "drill bit". There is a red locking switch that prevents
>> this switch (which moves left to right) from being unintentionally moved
>> from one setting to the other. This switch is located between the
>> aforementioned speed switch and the "drag" ring aft of the chuck.
> I would have to guess that the switch is to switch from drilling to screwing
> without having to turn the "drag collar" all the way up. My older one has
> five "drag" settings plus a drill setting on the collar. To go from driving
> with a low setting you have to turn the collar all the way up to the drill
> setting. I'm guessing you could leave yours set to(for example) a number 3
> for driving and then switch to drilling by moving the one switch.
> To test, try setting the collar at a "2" for example, with the switch in
> drive mode; now hold the chuck and turn the drill on. The drag clutch should
> slip at a fairly low power. Now, without moving the drag collar, change the
> button to "drill". If you try holding the chuck now, it should stop the
> drill IF you can hold it that tight.
That makes sense! I'll try as you suggest and report back. Thanks!!!
--
DC
(((:~{>
Leon wrote:
> "DC" <[email protected]> wrote in message
> news:[email protected]...
> does.
>> My question is in regards to the second, smaller switch, which also has
>> two
>> positions, each identified by a picture: one is a "screw", and the
>> other is a "drill bit". There is a red locking switch that prevents
>> this switch (which moves left to right) from being unintentionally moved
>> from one setting to the other. This switch is located between the
>> aforementioned speed switch and the "drag" ring aft of the chuck.
> This is a very useful switch. The drill switch setting is obviously for
> drilling but also over rides the clutch. If you are using small screws and
> are using a low number clutch setting you will easily strip out the screws
> or wood if you use the drill setting. If you use the screw setting to drill
> holes the clutch will slip.
Thanks for your feedback! I'm gonna play with it and figure this out.
Boy, the manual that came with the drill sure is useless.
--
DC
(((:~{>
Leon wrote:
>
>
> I use this feature all the time. Much easier to flip the switch from drill
> to screw rather than twist the clutch setting up and down. Especially when
> using small screws.
>
You guys only use one drill? <G>
I'll usually have one with the drill bit and another with the
screwdriver bit.