All but of couple of my upper doors are true divided lite. To make
these I purchased the freud 99-270 router bit set. For the lower doors
and drawer faces and two upper doors I was planing on flat panel
construction with the panel fitting into a grove in the rail and
stiles. The divided lite set won't make this type. It doesn't cut a
groove but a rabbit. Is it inappropriate to mount panels in a rabbit
and apply some kind of backing around the edge to hold it in just like
they were glass panels. I can't imagine why this won't work. But,
want to be sure before I mess up some expensive wood. Also, I want
things to look good and be "right". Would I be better off getting a
rail and stile set with a matching profile (its a plain cove) and go
that way?
Mike in Arkansas who is recovered from the kickback incident except for
a mighty itch near the ribs.
Mike in Arkansas wrote:
> All but of couple of my upper doors are true divided lite. To make
> these I purchased the freud 99-270 router bit set. For the lower doors
> and drawer faces and two upper doors I was planing on flat panel
> construction with the panel fitting into a grove in the rail and
> stiles. The divided lite set won't make this type. It doesn't cut a
> groove but a rabbit. Is it inappropriate to mount panels in a rabbit
> and apply some kind of backing around the edge to hold it in just like
> they were glass panels. I can't imagine why this won't work. But,
> want to be sure before I mess up some expensive wood. Also, I want
> things to look good and be "right". Would I be better off getting a
> rail and stile set with a matching profile (its a plain cove) and go
> that way?
> Mike in Arkansas who is recovered from the kickback incident except for
> a mighty itch near the ribs.
Is it possible to return the router bit set and get the right one? We
normally use a panel bit set to make frames for glass doors. Then use
a rabbit bit to remove the 1/4 back rail. This does require cutting
the corners with a chisel
In answer to your question, yes you could do it as you described. If
you have ever tried working with 1/4" quarter round, you will find it
challenging.
-Lee
[email protected] wrote:
> In answer to your question, yes you could do it as you described. If
> you have ever tried working with 1/4" quarter round, you will find it
> challenging.
>
> -Lee
Thanks for the input Lee. I didn't actually get the 'wrong' bits for
what I wanted. They did a fine job for what they were designed to do.
With so much time and money going into this everlasting gobstopper of a
project I don't want to do anything that would distract from the
quality just because I'm impatient and too cheap to buy tools
unnecessarily. Thanks again
Mike
Prometheus wrote:
> set the panel in place,
> and then glue a second thin set of rails and stiles to the back to
> effectively make a dado without cutting one.
Two interesting solutions Prometheus. Thanks for your input. I do
have a table saw so cutting the dado isn't a problem. Your suggestion
just made me realize that my rail and stile bit set comes apart so I
can simply replace the rabbeting cutter with spacers and have a
perfectly matched cove. Doh! Honestly, sometimes I can be such a
dolt. Thanks for fire by the way.
Mike in Arkansas
On 3 Nov 2006 20:55:16 -0800, "Mike in Arkansas" <[email protected]>
wrote:
>All but of couple of my upper doors are true divided lite. To make
>these I purchased the freud 99-270 router bit set. For the lower doors
>and drawer faces and two upper doors I was planing on flat panel
>construction with the panel fitting into a grove in the rail and
>stiles. The divided lite set won't make this type. It doesn't cut a
>groove but a rabbit. Is it inappropriate to mount panels in a rabbit
>and apply some kind of backing around the edge to hold it in just like
>they were glass panels. I can't imagine why this won't work. But,
>want to be sure before I mess up some expensive wood. Also, I want
>things to look good and be "right". Would I be better off getting a
>rail and stile set with a matching profile (its a plain cove) and go
>that way?
Well, Mike- I'm assuming you have a table saw from your mention of the
kickback incident below (glad to hear you're recovering.) So why not
rout the cove with a regular cove bit, then cut the dadoes with your
table saw? Even if you don't have a dado stack, you can do it with a
single blade and multiple passes- that's the way I've done it a lot of
times, and it works fine.
There's nothing really "inappropriate" about mounting the panels in a
rabbet, but it will not look as good as setting them in dadoes. If
you really just prefer to use the router method, or don't have a cove
bit, you could make the rails and stiles a little thinner (if that
will work with your bit set), rout the rabbet, set the panel in place,
and then glue a second thin set of rails and stiles to the back to
effectively make a dado without cutting one.
>Mike in Arkansas who is recovered from the kickback incident except for
>a mighty itch near the ribs.