I have a door jamb that is split where the bottom hinge was screwed
into the jamb. My initial thought was to trace an outline of a piece
of replacement wood over the cracked portion, cut it out, and then
slide in the replacement piece.
However, for strength, I'd want to glue it and I'm thinking that
sliding it in would scrape off the glue. Undersizing it would make
the joint weak. There probably isn't room on the backside of the jamb
for a sister board.
There's probably a simple solution...hints?
Thanks
On Mar 30, 11:28 am, "Leon" <[email protected]> wrote:
> "Greg Esres" <[email protected]> wrote in message
>
> news:[email protected]...
>
> >I have a door jamb that is split where the bottom hinge was screwed
> > into the jamb. My initial thought was to trace an outline of a piece
> > of replacement wood over the cracked portion, cut it out, and then
> > slide in the replacement piece.
>
> > However, for strength, I'd want to glue it and I'm thinking that
> > sliding it in would scrape off the glue. Undersizing it would make
> > the joint weak. There probably isn't room on the backside of the jamb
> > for a sister board.
>
> > There's probably a simple solution...hints?
>
> > Thanks
>
> Put glue in the split and clamp to close the split. The wood should not
> resplit in that location.
For every problem, there is a simple solution which will not work!
Joe G
<<See if the clamp (without glue) will close the gap--if not remove
the hinge.>>
I assumed that I would remove it anyway. The crack goes behind the
hinge.
<<Work the glue into the crack with a toothpick or blow through a
drinking straw. >>
And avoid inhaling?
<<The glued joint will be stronger than the wood itself! >>
Almost as good as duct tape!
Thanks!
On Fri, 30 Mar 2007 15:28:04 GMT, "Leon"
<[email protected]> wrote:
>
>"Greg Esres" <[email protected]> wrote in message
>news:[email protected]...
>>I have a door jamb that is split where the bottom hinge was screwed
>> into the jamb. My initial thought was to trace an outline of a piece
>> of replacement wood over the cracked portion, cut it out, and then
>> slide in the replacement piece.
>>
>> However, for strength, I'd want to glue it and I'm thinking that
>> sliding it in would scrape off the glue. Undersizing it would make
>> the joint weak. There probably isn't room on the backside of the jamb
>> for a sister board.
>>
>> There's probably a simple solution...hints?
>>
>> Thanks
>>
>
>Put glue in the split and clamp to close the split. The wood should not
>resplit in that location.
>
>
Might add... Use yellow woodworking glue. See if the clamp (without
glue) will close the gap--if not remove the hinge. Work the glue into
the crack with a toothpick or blow through a drinking straw. Clamp
for 24 hours. The glued joint will be stronger than the wood itself!
Leon wrote:
> Put glue in the split and clamp to close the split. The wood
should not
> resplit in that location.
Make that "glue" some epoxy thickened with micro-balloons to the
consistency of mayo and use light clamping pressure.
Thickened epoxy is very forgiving stuff.
When the wood returns to compost, the epoxy will still be there.
Lew
"Greg Esres" <[email protected]> wrote in message
news:[email protected]...
>I have a door jamb that is split where the bottom hinge was screwed
> into the jamb. My initial thought was to trace an outline of a piece
> of replacement wood over the cracked portion, cut it out, and then
> slide in the replacement piece.
>
> However, for strength, I'd want to glue it and I'm thinking that
> sliding it in would scrape off the glue. Undersizing it would make
> the joint weak. There probably isn't room on the backside of the jamb
> for a sister board.
>
> There's probably a simple solution...hints?
>
> Thanks
>
Put glue in the split and clamp to close the split. The wood should not
resplit in that location.