how's this for a clean cut?
http://www.knight-toolworks.com/web_temp_pics/maple.jpg
this is a Byrd carbide cutterhead by the way on my 6" jointer.
http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
On Mon, 25 Apr 2005 01:30:57 -0400, "J. Clarke"
<[email protected]> wrote:
>Prometheus wrote:
>
>> On Fri, 22 Apr 2005 09:54:11 -0700, Steve Knight
>> <[email protected]> wrote:
>>
>>>
>>>
>>>>Hey now, wait a minute... you make planes... Why in the heck you do
>>>>you have a jointer?
>>>
>>>if you want to come hand joint all my tropicals feel free to volunteer
>>>(G)you will look like Popeye after a bit (G)
>>
>> Nah, that's ok... I hand planed my workbench top, and my elbows ached
>> for days. Besides, how is hand jointing tropicals going to make me
>> squint one eye and smoke a pipe? :)
>
>Amazing what the resins that creep out of those exotics will do to you,
>isn't it? :)
Ahhh..guk,guk,guk,guk!
Aut inveniam viam aut faciam
Gerald Ross wrote:
> Steve Knight wrote:
> > how's this for a clean cut?
> > http://www.knight-toolworks.com/web_temp_pics/maple.jpg
> > this is a Byrd carbide cutterhead by the way on my 6" jointer.
> > http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
> >
> It wrinkled up that maple, now you're going to have to iron it.
> Looks good, though.
> --
> Gerald Ross
> Cochran, GA
>
> If rabbits feet are so lucky, what
> happened to the rabbit?
>
>
>
>
>
> ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet
News==----
> http://www.newsfeeds.com The #1 Newsgroup Service in the World!
120,000+ Newsgroups
> ----= East and West-Coast Server Farms - Total Privacy via Encryption
=----
So! after you iron the wrinkles off the maple does it become ironwood?
Steve Knight wrote:
> how's this for a clean cut?
> http://www.knight-toolworks.com/web_temp_pics/maple.jpg
> this is a Byrd carbide cutterhead by the way on my 6" jointer.
> http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
>
Awesome...That is a beautiful slice-O-wood!
I wish I had a joitner that could do that!!!
Philski
On 21 Apr 2005 12:55:52 -0700, "SonomaProducts.com" <[email protected]> wrote:
>Could you please send me that piece of Maple so I can look at the
>jointer finish a little closer?
>
I don't think I have seen a cooler piece of maple. though it is almost wasted on
a plane as the grain does not show as well on smaller things.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
On Wed, 20 Apr 2005 20:28:05 -0700, Steve Knight <[email protected]> wrote:
> how's this for a clean cut?
> http://www.knight-toolworks.com/web_temp_pics/maple.jpg
> this is a Byrd carbide cutterhead by the way on my 6" jointer.
> http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
Loverly. OK, show of hands, who else went up and looked at the
whole directory of pics?
> how's this for a clean cut?
> http://www.knight-toolworks.com/web_temp_pics/maple.jpg
> this is a Byrd carbide cutterhead by the way on my 6" jointer.
> http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
Forget the jointer, gimme that wood! :-)
Nice cuts btw!
--
Regards,
Dean Bielanowski
Editor,
Online Tool Reviews
http://www.onlinetoolreviews.com
------------------------------------------------------------
Latest 6 Reviews:
- Delta SS250 Scroll Saw (Review Updated)
- Porter Cable FR350A Framing Nailer
- WoodHaven Biscuit Master
- Veritas Saddle Square
- EZ Smart Guide System
- Incra V27 Miter Gauge
------------------------------------------------------------
Steve Knight wrote:
> how's this for a clean cut?
> http://www.knight-toolworks.com/web_temp_pics/maple.jpg
> this is a Byrd carbide cutterhead by the way on my 6" jointer.
> http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
>
It wrinkled up that maple, now you're going to have to iron it.
Looks good, though.
--
Gerald Ross
Cochran, GA
If rabbits feet are so lucky, what
happened to the rabbit?
----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
Steve Knight wrote:
> how's this for a clean cut?
Abso-freakin' gorgeous! Better show it to Mekon, tell him it's
bleached cherry. %-)
Dave in Fairfax
--
Dave Leader
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/
PATINA
http://www.Patinatools.org/
Dave Hinz wrote:
> On Wed, 20 Apr 2005 20:28:05 -0700, Steve Knight <[email protected]> wrote:
>
>
> Loverly. OK, show of hands, who else went up and looked at the
> whole directory of pics?
>
Hand up...
I was intrigued by the Garrett Hack letter.
On Wed, 20 Apr 2005 20:28:05 -0700, Steve Knight
<[email protected]> wrote:
>how's this for a clean cut?
>http://www.knight-toolworks.com/web_temp_pics/maple.jpg
>this is a Byrd carbide cutterhead by the way on my 6" jointer.
>http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
Hey now, wait a minute... you make planes... Why in the heck you do
you have a jointer?
Aut inveniam viam aut faciam
>Awesome...That is a beautiful slice-O-wood!
>
>I wish I had a joitner that could do that!!!
it only costs 370.00 (G) or only 195 for a hand powered jointer.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
>It must thrust the material laterally against the fence as well, eh?
>Will the inserts index themselves when rotated? Or does it go back to
>the manufacturer for an insert change?
>
no sideways pressure. it cuts a bit slow compared to regular knives though.
they index on their own. a 1/4 turn and you have a fresh surface again.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
It's probably much easier to scrape or sand the small lines than horrendeous
tear-out.
Clint
"TaskMule" <[email protected]> wrote in message
news:[email protected]...
>
> "Steve Knight" <[email protected]> wrote in message
> news:[email protected]...
> >
> >
> > >In that picture I can see lines parallel to the long edges. Are they
> > >noticable in real life too? My griz spiral does that, but they're
> > >only noticable when looking at the right angle in a favorable light.
> >
> > yes it does like a hand planed surface. not really a issue though.
> >
>
> So if it does leave small lines then the surface must be sanded, so what's
> the advantage of this cutterhead?
>
>
"Steve Knight" <[email protected]> wrote in message
news:[email protected]...
>
>
> >In that picture I can see lines parallel to the long edges. Are they
> >noticable in real life too? My griz spiral does that, but they're
> >only noticable when looking at the right angle in a favorable light.
>
> yes it does like a hand planed surface. not really a issue though.
>
So if it does leave small lines then the surface must be sanded, so what's
the advantage of this cutterhead?
"Steve Knight" <[email protected]> wrote in message
news:[email protected]...
> On 21 Apr 2005 12:55:52 -0700, "SonomaProducts.com" <[email protected]>
wrote:
>
> >Could you please send me that piece of Maple so I can look at the
> >jointer finish a little closer?
> >
>
> I don't think I have seen a cooler piece of maple. though it is almost
wasted on
> a plane as the grain does not show as well on smaller things.
It's certainly worthy of slicing into veneer
I think I'd prefer lines to ripples.
-j
"Steve Knight" <[email protected]> wrote in message
news:[email protected]...
>
>
> >So if it does leave small lines then the surface must be sanded, so
what's
> >the advantage of this cutterhead?
> >
>
> and a regular head leaves ripples. because it cuts without tearout and
lasts a
> log time between rotating the cutters. plus it does endgrain great. Plus
it is
> very easy to change the cutters. You don't have to re setup your machine.
>
> --
> Knight-Toolworks & Custom Planes
> Custom made wooden planes at reasonable prices
> See http://www.knight-toolworks.com For prices and ordering instructions.
Prometheus wrote:
> On Fri, 22 Apr 2005 09:54:11 -0700, Steve Knight
> <[email protected]> wrote:
>
>>
>>
>>>Hey now, wait a minute... you make planes... Why in the heck you do
>>>you have a jointer?
>>
>>if you want to come hand joint all my tropicals feel free to volunteer
>>(G)you will look like Popeye after a bit (G)
>
> Nah, that's ok... I hand planed my workbench top, and my elbows ached
> for days. Besides, how is hand jointing tropicals going to make me
> squint one eye and smoke a pipe? :)
Amazing what the resins that creep out of those exotics will do to you,
isn't it? :)
> Aut inveniam viam aut faciam
--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)
In article <[email protected]>,
Steve Knight <[email protected]> wrote:
> how's this for a clean cut?
> http://www.knight-toolworks.com/web_temp_pics/maple.jpg
> this is a Byrd carbide cutterhead by the way on my 6" jointer.
> http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
Astounding, Steve. How thin a flitch will it do at that quality?
It must thrust the material laterally against the fence as well, eh?
Will the inserts index themselves when rotated? Or does it go back to
the manufacturer for an insert change?
Rob
>In that picture I can see lines parallel to the long edges. Are they
>noticable in real life too? My griz spiral does that, but they're
>only noticable when looking at the right angle in a favorable light.
yes it does like a hand planed surface. not really a issue though.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
On Thu, 21 Apr 2005 22:52:27 -0500, Mike <[email protected]> wrote:
>Steve, are you going to offer a spiral cutterhead in your planes?
gonna be hard to mount the motor (G)
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
>Hey now, wait a minute... you make planes... Why in the heck you do
>you have a jointer?
if you want to come hand joint all my tropicals feel free to volunteer (G)you
will look like Popeye after a bit (G)
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
Steve, are you going to offer a spiral cutterhead in your planes?
On Wed, 20 Apr 2005 20:28:05 -0700, Steve Knight
<[email protected]> wrote:
>how's this for a clean cut?
>http://www.knight-toolworks.com/web_temp_pics/maple.jpg
>this is a Byrd carbide cutterhead by the way on my 6" jointer.
>http://www.knight-toolworks.com/web_temp_pics/cutter3.jpg
On Fri, 22 Apr 2005 09:54:11 -0700, Steve Knight
<[email protected]> wrote:
>
>
>>Hey now, wait a minute... you make planes... Why in the heck you do
>>you have a jointer?
>
>if you want to come hand joint all my tropicals feel free to volunteer (G)you
>will look like Popeye after a bit (G)
Nah, that's ok... I hand planed my workbench top, and my elbows ached
for days. Besides, how is hand jointing tropicals going to make me
squint one eye and smoke a pipe? :)
Aut inveniam viam aut faciam
>So if it does leave small lines then the surface must be sanded, so what's
>the advantage of this cutterhead?
>
and a regular head leaves ripples. because it cuts without tearout and lasts a
log time between rotating the cutters. plus it does endgrain great. Plus it is
very easy to change the cutters. You don't have to re setup your machine.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
Steve Knight <[email protected]> writes:
> how's this for a clean cut?
In that picture I can see lines parallel to the long edges. Are they
noticable in real life too? My griz spiral does that, but they're
only noticable when looking at the right angle in a favorable light.