A follow up on the thread on using a shop vac as a dust collector. I
have a Ridgid vac with 2 1/4" hoses, however the connection at the vac
is of the clip on type (hose end clips in with a small tab, rather than
friction fit, so you can drag the vac around by the hose without it
pulling out), and the actual vac inlet opening is closer to 2 11/16". I
would like to use this as a dust collector on my Bosch slide miter saw,
which has a 1 1/2" dust collection fitting. Would like to use about 12
feet of 1 1/2" hose to connect the vac to the saw. I can't find
anything like this, there appear to be some places that can make it up,
but they're pretty expensive (~$100). Anyone know where I can get a
hose of the type I need for a reasonable price?
TIA
Dan
Dan wrote:
> A follow up on the thread on using a shop vac as a dust collector. I
> have a Ridgid vac with 2 1/4" hoses, however the connection at the vac
> is of the clip on type (hose end clips in with a small tab, rather than
> friction fit, so you can drag the vac around by the hose without it
> pulling out), and the actual vac inlet opening is closer to 2 11/16". I
> would like to use this as a dust collector on my Bosch slide miter saw,
> which has a 1 1/2" dust collection fitting. Would like to use about 12
> feet of 1 1/2" hose to connect the vac to the saw. I can't find
> anything like this, there appear to be some places that can make it up,
> but they're pretty expensive (~$100). Anyone know where I can get a
> hose of the type I need for a reasonable price?
>
> TIA
>
> Dan
a source for high quality hose of that general type is any swimming
pool supply house. you'll have to make up your own ends, but they have
the hose.
> Dave-Thanks for the reply. Saw is a 5412, new a couple months ago.
> Looking at the saw from the right side, if the blade were a clock face
> the port's at about 10, but since it sits rear of the motor, it forms a
> scoop down to about the middle of the blade (9 o'clock). I've found
> without the bag, a fair amount of dust does seem to spew from the port
> (not that the bag manages to catch much when it IS there ;-/ ) I'll
> try cobbling up some 1.5" hose to the 2.25" from the vac with duct tape,
> just to see if the port is effective at all. Again I think since the
> saw head moves around so much in use these are especially difficult.
>
> Dan
Re: port position, I meant looking at the saw from the LEFT side.
Dan wrote:
> A follow up on the thread on using a shop vac as a dust collector. I
> have a Ridgid vac with 2 1/4" hoses.....I
> would like to use this as a dust collector on my Bosch slide miter saw,
> which has a 1 1/2" dust collection fitting.
Try looking for an adapter to connect a short length of narrow hose to
your existing hose.
On my non-slider I just use the full size hose with an adapter directly
coupled to the saw.
Chris
Tyke wrote:
> I do not know which model of Bosch saw you have, but if the dust port is on
> the top of the blade guard, then any connection to a vac or dust collector
> will be ineffective.
>
> I have a Bosch SCMS and even when made a temporary adaptor to directly
> attach my Fein shop vac, which has the best suction of any of my earlier
> shop vacs, the result was disappointing.
>
> The root cause is that most of the dust particles are propelled forward and
> not much is carried upward by the blade.
>
> This is reinforced when I see the latest models which now have dust ports
> forward of the blade.
>
> What I found worked for me was a happy accident. I had attached the vac
> hose with a brush fitting of my shop vac to the temporary adaptor at the top
> of the blade guard. During the cut the vac hose came loose and the brush
> end came to rest in front of the SCMS head which holds the sliding rods and
> so the brush was in front of the blade. To my surprise this caught more of
> the dust than ever before.
>
> So now when I use the SCMS, I merely lay the vac hose and brush fitting in
> front of the head. I actually leave the blade guard port open and do not
> seem to be getting any dust out of this port with my arrangement.
>
> Poor mans front facing dust collection design.
>
> Dave Paine.
>
Dave-Thanks for the reply. Saw is a 5412, new a couple months ago.
Looking at the saw from the right side, if the blade were a clock face
the port's at about 10, but since it sits rear of the motor, it forms a
scoop down to about the middle of the blade (9 o'clock). I've found
without the bag, a fair amount of dust does seem to spew from the port
(not that the bag manages to catch much when it IS there ;-/ ) I'll
try cobbling up some 1.5" hose to the 2.25" from the vac with duct tape,
just to see if the port is effective at all. Again I think since the
saw head moves around so much in use these are especially difficult.
Dan
On Fri, 11 Aug 2006 11:51:21 -0700, Dan <[email protected]> wrote:
>A follow up on the thread on using a shop vac as a dust collector. I
>have a Ridgid vac with 2 1/4" hoses, however the connection at the vac
>is of the clip on type (hose end clips in with a small tab, rather than
>friction fit, so you can drag the vac around by the hose without it
>pulling out), and the actual vac inlet opening is closer to 2 11/16". I
>would like to use this as a dust collector on my Bosch slide miter saw,
>which has a 1 1/2" dust collection fitting. Would like to use about 12
>feet of 1 1/2" hose to connect the vac to the saw. I can't find
>anything like this, there appear to be some places that can make it up,
>but they're pretty expensive (~$100). Anyone know where I can get a
>hose of the type I need for a reasonable price?
>
>TIA
>
>Dan
Dan... maybe something like this??
http://www.leevalley.com/wood/page.aspx?c=2&p=30198&cat=1,42401&ap=1
Mac
https://home.comcast.net/~mac.davis
https://home.comcast.net/~mac.davis/wood_stuff.htm
Ditto. I've tried a number of things with my Bosch slider (again, the
as-built dust collection port worked poorly with every conceivable
customization). I had finally found a "sweet spot" toward the front,
albeit, I'm still trying to figure something better than my duct tape
connection to hold in place. Thinking in terms of some type of
shroud assembly for that general area.
On Sat, 12 Aug 2006 10:37:37 -0400, "Tyke" <[email protected]> wrote:
>I do not know which model of Bosch saw you have, but if the dust port is on
>the top of the blade guard, then any connection to a vac or dust collector
>will be ineffective.
>
>I have a Bosch SCMS and even when made a temporary adaptor to directly
>attach my Fein shop vac, which has the best suction of any of my earlier
>shop vacs, the result was disappointing.
>
>The root cause is that most of the dust particles are propelled forward and
>not much is carried upward by the blade.
>
>This is reinforced when I see the latest models which now have dust ports
>forward of the blade.
>
>What I found worked for me was a happy accident. I had attached the vac
>hose with a brush fitting of my shop vac to the temporary adaptor at the top
>of the blade guard. During the cut the vac hose came loose and the brush
>end came to rest in front of the SCMS head which holds the sliding rods and
>so the brush was in front of the blade. To my surprise this caught more of
>the dust than ever before.
>
>So now when I use the SCMS, I merely lay the vac hose and brush fitting in
>front of the head. I actually leave the blade guard port open and do not
>seem to be getting any dust out of this port with my arrangement.
>
>Poor mans front facing dust collection design.
>
>Dave Paine.
>
>
>"Dan" <[email protected]> wrote in message
>news:[email protected]...
>>A follow up on the thread on using a shop vac as a dust collector. I have
>>a Ridgid vac with 2 1/4" hoses, however the connection at the vac is of the
>>clip on type (hose end clips in with a small tab, rather than friction fit,
>>so you can drag the vac around by the hose without it pulling out), and the
>>actual vac inlet opening is closer to 2 11/16". I would like to use this
>>as a dust collector on my Bosch slide miter saw, which has a 1 1/2" dust
>>collection fitting. Would like to use about 12 feet of 1 1/2" hose to
>>connect the vac to the saw. I can't find anything like this, there appear
>>to be some places that can make it up, but they're pretty expensive
>>(~$100). Anyone know where I can get a hose of the type I need for a
>>reasonable price?
>>
>> TIA
>>
>> Dan
>
--
Monroe
Use sump pump hose, that's about 1 1/2" and a little duck tape to hold it
on.
"Dan" <[email protected]> wrote in message
news:[email protected]...
>A follow up on the thread on using a shop vac as a dust collector. I have
>a Ridgid vac with 2 1/4" hoses, however the connection at the vac is of the
>clip on type (hose end clips in with a small tab, rather than friction fit,
>so you can drag the vac around by the hose without it pulling out), and the
>actual vac inlet opening is closer to 2 11/16". I would like to use this
>as a dust collector on my Bosch slide miter saw, which has a 1 1/2" dust
>collection fitting. Would like to use about 12 feet of 1 1/2" hose to
>connect the vac to the saw. I can't find anything like this, there appear
>to be some places that can make it up, but they're pretty expensive
>(~$100). Anyone know where I can get a hose of the type I need for a
>reasonable price?
>
> TIA
>
> Dan
I do not know which model of Bosch saw you have, but if the dust port is on
the top of the blade guard, then any connection to a vac or dust collector
will be ineffective.
I have a Bosch SCMS and even when made a temporary adaptor to directly
attach my Fein shop vac, which has the best suction of any of my earlier
shop vacs, the result was disappointing.
The root cause is that most of the dust particles are propelled forward and
not much is carried upward by the blade.
This is reinforced when I see the latest models which now have dust ports
forward of the blade.
What I found worked for me was a happy accident. I had attached the vac
hose with a brush fitting of my shop vac to the temporary adaptor at the top
of the blade guard. During the cut the vac hose came loose and the brush
end came to rest in front of the SCMS head which holds the sliding rods and
so the brush was in front of the blade. To my surprise this caught more of
the dust than ever before.
So now when I use the SCMS, I merely lay the vac hose and brush fitting in
front of the head. I actually leave the blade guard port open and do not
seem to be getting any dust out of this port with my arrangement.
Poor mans front facing dust collection design.
Dave Paine.
"Dan" <[email protected]> wrote in message
news:[email protected]...
>A follow up on the thread on using a shop vac as a dust collector. I have
>a Ridgid vac with 2 1/4" hoses, however the connection at the vac is of the
>clip on type (hose end clips in with a small tab, rather than friction fit,
>so you can drag the vac around by the hose without it pulling out), and the
>actual vac inlet opening is closer to 2 11/16". I would like to use this
>as a dust collector on my Bosch slide miter saw, which has a 1 1/2" dust
>collection fitting. Would like to use about 12 feet of 1 1/2" hose to
>connect the vac to the saw. I can't find anything like this, there appear
>to be some places that can make it up, but they're pretty expensive
>(~$100). Anyone know where I can get a hose of the type I need for a
>reasonable price?
>
> TIA
>
> Dan
mac davis wrote:
>
>
> Dan... maybe something like this??
>
> http://www.leevalley.com/wood/page.aspx?c=2&p=30198&cat=1,42401&ap=1
>
> Mac
>
> https://home.comcast.net/~mac.davis
> https://home.comcast.net/~mac.davis/wood_stuff.htm
That looks like it would be quite handy in general, and not too
expensive. Thanks!
BTW, you're not the Mac Davis who was a singer about a zillion years ago
(you know, during the 70's ;-), are you?
http://www.allmusic.com/cg/amg.dll?p=amg&sql=11:fyem97y7kr0t
Dan
Dan <[email protected]> wrote in
news:[email protected]:
> A follow up on the thread on using a shop vac as a dust collector. I
> have a Ridgid vac with 2 1/4" hoses, however the connection at the vac
> is of the clip on type (hose end clips in with a small tab, rather
> than friction fit, so you can drag the vac around by the hose without
> it pulling out), and the actual vac inlet opening is closer to 2
> 11/16". I would like to use this as a dust collector on my Bosch
> slide miter saw, which has a 1 1/2" dust collection fitting. Would
> like to use about 12 feet of 1 1/2" hose to connect the vac to the
> saw. I can't find anything like this, there appear to be some places
> that can make it up, but they're pretty expensive (~$100). Anyone
> know where I can get a hose of the type I need for a reasonable price?
>
> TIA
>
> Dan
I did this something similar to this with some hose I picked up at the
local hardware store to hook up my P-C 89x to my shop vac. The hose was
fiber-reinforced to prevent it from collapsing under vacuum. Cost was
around $.90/ft. I used a "standard" 2-1/2" multi-step adapter to make
the transition from the vac to the hose.
Worked pretty well -- much better than not using anything, and sweeping
up after.
--
I was punching a text message into my phone | Reed Snellenberger
yesterday and thought, "They need to make a | rsnellenberger
phone that you can just talk into." | -at-houston.rr.com
On Tue, 15 Aug 2006 18:31:47 -0700, Dan <[email protected]> wrote:
>Tim Taylor wrote:
>>> BTW, you're not the Mac Davis who was a singer about a zillion years ago
>>> (you know, during the 70's ;-), are you?
>>> http://www.allmusic.com/cg/amg.dll?p=amg&sql=11:fyem97y7kr0t
>>>
>>> Dan
>>
>> OUCH!!!!
>>
>>
>
>You're not the Tim Taylor who had a TV show about HALF a zillion years
>ago, are you?!?
>
>Who'da thought so many CELEBRITIES were into woodworking????
>
>All in good fun. After all, if I'm old enough to REMEMBER this crap...
>well, 'nough said... ;-)
>
>Dan
Sorta funny.... We go to dinner every month or so with our friend Jerry and his
wife.... I never realized the connection of his last name until a waitress asked
me if I was the "real" Mac Davis" and he said "Yeah, he is, and I'm Jerry
Reed".. rofl
Oh.. and my guy at the saw shop is Barry White..
Mac
https://home.comcast.net/~mac.davis
https://home.comcast.net/~mac.davis/wood_stuff.htm
Phisherman wrote:
> On Fri, 11 Aug 2006 11:51:21 -0700, Dan <[email protected]> wrote:
>
>> A follow up on the thread on using a shop vac as a dust collector. I
>> have a Ridgid vac with 2 1/4" hoses, however the connection at the vac
>> is of the clip on type (hose end clips in with a small tab, rather than
>> friction fit, so you can drag the vac around by the hose without it
>> pulling out), and the actual vac inlet opening is closer to 2 11/16". I
>> would like to use this as a dust collector on my Bosch slide miter saw,
>> which has a 1 1/2" dust collection fitting. Would like to use about 12
>> feet of 1 1/2" hose to connect the vac to the saw. I can't find
>> anything like this, there appear to be some places that can make it up,
>> but they're pretty expensive (~$100). Anyone know where I can get a
>> hose of the type I need for a reasonable price?
>>
>> TIA
>>
>> Dan
>
> The vac hoses I've seen are expensive. At this point you should
> consider moving up to a DC and use the 4" hoses to draw a larger
> volume--that will catch a lot more dust and your lungs will appreciate
> it. A shop vac is still useful to have around.
Thanks for the reply. No doubt a real DC system is much more effective,
the problem is, I don't have much room in my garage work space. At the
moment I only have the miter saw & a drill press, though I'm leaning
toward getting a router table, not sure where I'll put it! Before I
moved, I had a Unisaw, I don't even think I could squeeze a contractor's
saw in this very tight 2 car garage.
Dan
Chris Friesen wrote:
> Dan wrote:
>> A follow up on the thread on using a shop vac as a dust collector. I
>> have a Ridgid vac with 2 1/4" hoses.....I
>> would like to use this as a dust collector on my Bosch slide miter
>> saw, which has a 1 1/2" dust collection fitting.
>
> Try looking for an adapter to connect a short length of narrow hose to
> your existing hose.
>
> On my non-slider I just use the full size hose with an adapter directly
> coupled to the saw.
>
> Chris
Thanks Chris, yeah I think that would work on most stationary tools like
a table saw, but especially given the sliding/compound mitering aspect
of this saw, I think the big hose may prove a bit cumbersome. I cound
use it for all but the last 5 feet or so, again if I can find suitable
1.5" hose/adapters/couplers.
Dan
[email protected] wrote:
> Dan wrote:
>> A follow up on the thread on using a shop vac as a dust collector. I
>> have a Ridgid vac with 2 1/4" hoses, however the connection at the vac
>> is of the clip on type (hose end clips in with a small tab, rather than
>> friction fit, so you can drag the vac around by the hose without it
>> pulling out), and the actual vac inlet opening is closer to 2 11/16". I
>> would like to use this as a dust collector on my Bosch slide miter saw,
>> which has a 1 1/2" dust collection fitting. Would like to use about 12
>> feet of 1 1/2" hose to connect the vac to the saw. I can't find
>> anything like this, there appear to be some places that can make it up,
>> but they're pretty expensive (~$100). Anyone know where I can get a
>> hose of the type I need for a reasonable price?
>>
>> TIA
>>
>> Dan
>
> a source for high quality hose of that general type is any swimming
> pool supply house. you'll have to make up your own ends, but they have
> the hose.
>
Thanks for the suggestion, worth a look!
Dan
Tim Taylor wrote:
>> BTW, you're not the Mac Davis who was a singer about a zillion years ago
>> (you know, during the 70's ;-), are you?
>> http://www.allmusic.com/cg/amg.dll?p=amg&sql=11:fyem97y7kr0t
>>
>> Dan
>
> OUCH!!!!
>
>
You're not the Tim Taylor who had a TV show about HALF a zillion years
ago, are you?!?
Who'da thought so many CELEBRITIES were into woodworking????
All in good fun. After all, if I'm old enough to REMEMBER this crap...
well, 'nough said... ;-)
Dan
On Fri, 11 Aug 2006 11:51:21 -0700, Dan <[email protected]> wrote:
>A follow up on the thread on using a shop vac as a dust collector. I
>have a Ridgid vac with 2 1/4" hoses, however the connection at the vac
>is of the clip on type (hose end clips in with a small tab, rather than
>friction fit, so you can drag the vac around by the hose without it
>pulling out), and the actual vac inlet opening is closer to 2 11/16". I
>would like to use this as a dust collector on my Bosch slide miter saw,
>which has a 1 1/2" dust collection fitting. Would like to use about 12
>feet of 1 1/2" hose to connect the vac to the saw. I can't find
>anything like this, there appear to be some places that can make it up,
>but they're pretty expensive (~$100). Anyone know where I can get a
>hose of the type I need for a reasonable price?
>
>TIA
>
>Dan
The vac hoses I've seen are expensive. At this point you should
consider moving up to a DC and use the 4" hoses to draw a larger
volume--that will catch a lot more dust and your lungs will appreciate
it. A shop vac is still useful to have around.
"Dan" <[email protected]> wrote in message
news:[email protected]...
> mac davis wrote:
>>
>>
>> Dan... maybe something like this??
>>
>> http://www.leevalley.com/wood/page.aspx?c=2&p=30198&cat=1,42401&ap=1
>>
>> Mac
>>
>> https://home.comcast.net/~mac.davis
>> https://home.comcast.net/~mac.davis/wood_stuff.htm
>
> That looks like it would be quite handy in general, and not too expensive.
> Thanks!
>
> BTW, you're not the Mac Davis who was a singer about a zillion years ago
> (you know, during the 70's ;-), are you?
> http://www.allmusic.com/cg/amg.dll?p=amg&sql=11:fyem97y7kr0t
>
> Dan
OUCH!!!!
"Dan" <[email protected]> wrote in message
news:[email protected]...
>A follow up on the thread on using a shop vac as a dust collector. I have
>a Ridgid vac with 2 1/4" hoses, however the connection at the vac is of the
>clip on type (hose end clips in with a small tab, rather than friction fit,
>so you can drag the vac around by the hose without it pulling out), and the
>actual vac inlet opening is closer to 2 11/16". I would like to use this
>as a dust collector on my Bosch slide miter saw, which has a 1 1/2" dust
>collection fitting. Would like to use about 12 feet of 1 1/2" hose to
>connect the vac to the saw. I can't find anything like this, there appear
>to be some places that can make it up, but they're pretty expensive
>(~$100). Anyone know where I can get a hose of the type I need for a
>reasonable price?
>
> TIA
>
> Dan
Think duct tape! :-)
On Tue, 15 Aug 2006 17:27:18 -0700, Dan <[email protected]> wrote:
>mac davis wrote:
>>
>>
>> Dan... maybe something like this??
>>
>> http://www.leevalley.com/wood/page.aspx?c=2&p=30198&cat=1,42401&ap=1
>>
>> Mac
>>
>> https://home.comcast.net/~mac.davis
>> https://home.comcast.net/~mac.davis/wood_stuff.htm
>
>That looks like it would be quite handy in general, and not too
>expensive. Thanks!
>
>BTW, you're not the Mac Davis who was a singer about a zillion years ago
>(you know, during the 70's ;-), are you?
>http://www.allmusic.com/cg/amg.dll?p=amg&sql=11:fyem97y7kr0t
>
>Dan
Nah.... his real name is Morris Mac Davis.. lol
My first name is Max but I haven't used it since I was a little kid, unless I
had to for school or legal crap..
Mac
https://home.comcast.net/~mac.davis
https://home.comcast.net/~mac.davis/wood_stuff.htm
On Sat, 12 Aug 2006 16:55:16 GMT, Monroe <[email protected]> wrote:
>Ditto. I've tried a number of things with my Bosch slider (again, the
>as-built dust collection port worked poorly with every conceivable
>customization). I had finally found a "sweet spot" toward the front,
>albeit, I'm still trying to figure something better than my duct tape
>connection to hold in place. Thinking in terms of some type of
>shroud assembly for that general area.
>
I use the crapsman, so I'm not sure who makes it or what brand it's like, but
this worked pretty well for me:
I had several old 2x4's that were going to be firewood so I used them to sort of
test where the saw was kicking out the most crap...
I'd vacuum the area around the saw, make a few cuts and note where it shot the
most dust...
It seemed like with or with out dust collection, most was shooting back and
down, sort of between the vac port and the zero clearance plate..
I put the bag back on the port and put a DC hood (I think they called it a
jointer hood) on the table behind the saw, in the path of the crap coming off
the blade... seems to work pretty well for me.. YMWV
Mac
https://home.comcast.net/~mac.davis
https://home.comcast.net/~mac.davis/wood_stuff.htm