"Roger Shoaf" <[email protected]> wrote in message
news:[email protected]...
> Did you use dowels in this project?
>
>
NO.
Leon wrote:
>
> The only problem I ran into was with the results of gluing the 3 sections
> separately. Because you are using a lot of moisture in the glue to glue
> this all together the center tends to want to bulge out between the ends.
> This resulted in the sides not being flat and would not glue together.
> Placing a third clamp in the center did not resolve this problem. I ended
> up having to use a cross cut sled to make the mating glue surfaces straight
> again. No big deal.
> The solution would be to glue all the piece together at one time. The
> problem with that would be the pieces 20 pieces slipping and moving around
> as you apply pressure.
>
> If I make another I will probably do the glue up all at one time and use a
> brad nailer to hold the pieces into position before clamping.
>
> The flatter your end result, the less sanding you will have to do. I spent
> about 15 minutes on each side with 80 grit sand paper and a ROS.
>
> My Fein Multimaster and its scraper blade worked great for quickly removing
> the beads of squeeze out glue along each row. before sanding.
>
> Other than that, it was a simple and fun project.
Do you think a jig similar to this one would help gluing it all at
once?
http://www.woodworkingtips.com/etips/etip011221wb.html
Replacing the hardboard cleats with thicker material and using bar
clamps and a caul to pull all of the pieces toward the corner.
Did you use dowels in this project?
--
Roger Shoaf
If you are not part of the solution, you are not dissolved in the solvent.
"Leon" <[email protected]> wrote in message
news:[email protected]...
> I posted a couple of pictures on a.b.p.w. of cutting boards that I built
in
> the last couple of days. The latest Wood magazine has the details.
>
>
"RayV" <[email protected]> wrote in message
news:[email protected]...
>
> Leon wrote:
>> I posted a couple of pictures on a.b.p.w. of cutting boards that I built
>> in
>> the last couple of days. The latest Wood magazine has the details.
>
> You work fast! I just finished reading that issue. What kind of wood
> did you use and did you encounter any problems?
>
Cherry, Walnut, and Maple.
The only problem I ran into was with the results of gluing the 3 sections
separately. Because you are using a lot of moisture in the glue to glue
this all together the center tends to want to bulge out between the ends.
This resulted in the sides not being flat and would not glue together.
Placing a third clamp in the center did not resolve this problem. I ended
up having to use a cross cut sled to make the mating glue surfaces straight
again. No big deal.
The solution would be to glue all the piece together at one time. The
problem with that would be the pieces 20 pieces slipping and moving around
as you apply pressure.
If I make another I will probably do the glue up all at one time and use a
brad nailer to hold the pieces into position before clamping.
The flatter your end result, the less sanding you will have to do. I spent
about 15 minutes on each side with 80 grit sand paper and a ROS.
My Fein Multimaster and its scraper blade worked great for quickly removing
the beads of squeeze out glue along each row. before sanding.
Other than that, it was a simple and fun project.
"RayV" <[email protected]> wrote in message
news:[email protected]...
>>
> Do you think a jig similar to this one would help gluing it all at
> once?
>
> http://www.woodworkingtips.com/etips/etip011221wb.html
>
> Replacing the hardboard cleats with thicker material and using bar
> clamps and a caul to pull all of the pieces toward the corner.
>
Yes, that would probably work well. Anything to prevent movement as you
apply pressure.