Afternoon all,
I need to round over the edge of a piece of 3/4" ROak with a 9" dia.
Is there an easy and safe way to do this on a router table. I could place a
pin
(bolt) in the router table about 2" from the bit and use it as a guide, but,
not sure if
that's a good idea or not. Any thoughts on this method?
Or is it better to secure it to a larger piece of wood and use a handheld
router?
Problem here is 'hiding' the holes on the top (good) side.
Would carpet tape hold it in place well enough?
Any suggestions would be appreciated,
Ron
I would not do this by hand. You have a router table so set two pins
in the table top (or, better yet, a temporary table top--allows a
mistake or two), one on either side of the bit and spaced (from the
cutting edge and each other) to give you the radius you need. Use a
test piece or two to get it right. With this method there is no need
for holes in the work piece. Use the pins as guides, keeping steady
but light pressure against both as you rotate the work through the bit.
You could also use one pin in the table and your fence as guides (I
believe).
Good luck. (What 'r ya makin"?)
Dan
[email protected] wrote:
>
> I would not do this by hand. You have a router table so set two pins
> in the table top (or, better yet, a temporary table top--allows a
> mistake or two), one on either side of the bit and spaced (from the
> cutting edge and each other) to give you the radius you need. Use a
> test piece or two to get it right. With this method there is no need
> for holes in the work piece. Use the pins as guides, keeping steady
> but light pressure against both as you rotate the work through the bit.
>
> You could also use one pin in the table and your fence as guides (I
> believe).
>
More reliable (imo) is to make pattern and use double-sided tape and
guide bearing
Duane Bozarth wrote:
>
> [email protected] wrote:
> >
> > I would not do this by hand. You have a router table so set two pins
> > in the table top (or, better yet, a temporary table top--allows a
> > mistake or two), one on either side of the bit and spaced (from the
> > cutting edge and each other) to give you the radius you need. Use a
> > test piece or two to get it right. With this method there is no need
> > for holes in the work piece. Use the pins as guides, keeping steady
> > but light pressure against both as you rotate the work through the bit.
> >
> > You could also use one pin in the table and your fence as guides (I
> > believe).
> >
>
> More reliable (imo) is to make pattern and use double-sided tape and
> guide bearing
That's assuming the reason for the question is that you want the full
3/4" (or nearly, anyway edge rounded so you don't have a bearing
surface). That's why I think this is more reliable than the pins as you
have a clean, untouched edged...
Get you one of those router mats that sell for about $8 and use the router
by hand. Nothing moves once you set the piece on the mat. Just be sure
that the depth of the bit isn't so deep that you cut through the mat while
you rout.
And I'm not saying how I know you should avoid that....
"Ron" <[email protected]> wrote in message
news:[email protected]...
> Afternoon all,
>
> I need to round over the edge of a piece of 3/4" ROak with a 9" dia.
>
> Is there an easy and safe way to do this on a router table. I could place
> a pin
> (bolt) in the router table about 2" from the bit and use it as a guide,
> but, not sure if
> that's a good idea or not. Any thoughts on this method?
>
> Or is it better to secure it to a larger piece of wood and use a handheld
> router?
> Problem here is 'hiding' the holes on the top (good) side.
> Would carpet tape hold it in place well enough?
>
> Any suggestions would be appreciated,
> Ron
>
He probably means he wants to nose the piece...rounding from both sides, so
there's no place for the bearing to run on the second pass.
Wilson
"Robatoy" <[email protected]> wrote in message
news:[email protected]...
> In article <[email protected]>,
> "Ron" <[email protected]> wrote:
>
>> Afternoon all,
>>
>> I need to round over the edge of a piece of 3/4" ROak with a 9" dia.
>>
>> Is there an easy and safe way to do this on a router table. I could
>> place a
>> pin
>> (bolt) in the router table about 2" from the bit and use it as a guide,
>> but,
>> not sure if
>> that's a good idea or not. Any thoughts on this method?
>>
>> Or is it better to secure it to a larger piece of wood and use a handheld
>> router?
>> Problem here is 'hiding' the holes on the top (good) side.
>> Would carpet tape hold it in place well enough?
>>
>> Any suggestions would be appreciated,
>> Ron
>>
>>
>
> Is there a reason you can't use a round-over bit with a bearing?
> In that case a table would be sufficiently safe to use.
>
> http://www.carbide.com/catalog/RBits_Radius.cfm?GroupID=0201.02.01
You could clamp two pieces of wood to the router table, placing them in a
"V" angle (sort of like the flippers on a pinball machine) with the cutter
centered at the bottom of the "V". This will keep the workpiece from being
cut to deep if you do not use a bit with a bearing.
Jay
"Ron" <[email protected]> wrote in message
news:[email protected]...
> Afternoon all,
>
> I need to round over the edge of a piece of 3/4" ROak with a 9" dia.
>
> Is there an easy and safe way to do this on a router table. I could place
> a pin
> (bolt) in the router table about 2" from the bit and use it as a guide,
> but, not sure if
> that's a good idea or not. Any thoughts on this method?
>
> Or is it better to secure it to a larger piece of wood and use a handheld
> router?
> Problem here is 'hiding' the holes on the top (good) side.
> Would carpet tape hold it in place well enough?
>
> Any suggestions would be appreciated,
> Ron
>
A lot of good ideas guys, many ThankX.
This piece is to be used as a top of a plant stand. I'm planning on using
an oak balluster for the single leg.
My roundover bit does have a roller bearing.
I was planning on rounding over both sides, but, doing just the top edge
will be OK.
I do have a router mat, but, forgot all about it.
I'll probably try either the pin(s) or the V angles methods.
I'll let you know how it works out.
ThankX again,
Ron
"Ron" <[email protected]> wrote in message
news:[email protected]...
> I need to round over the edge of a piece of 3/4" ROak with a 9" dia.
Why can't you just use a roundover bit with pilot bearing in your table.
With a 9" diameter, you shouldn't need any pins, fences or anything else.
Just hold it with both hands and be careful to feed in the right direction.
I've done a lot of round over stuff using this approach and its very easy
and clean, if you have a high quality bit with good bearing.
An alternative is a hand held laminate trimmer with pilot bearing round over
bit.
Bob
"Harvey Levin" <[email protected]> wrote in message
news:8sHYd.62365$7z6.26073@lakeread04...
> Get you one of those router mats that sell for about $8 and use the router
> by hand. Nothing moves once you set the piece on the mat. Just be sure
> that the depth of the bit isn't so deep that you cut through the mat while
> you rout.
>
> And I'm not saying how I know you should avoid that....
>
Glad I'm not the only one!
--
Nahmie
Those on the cutting edge bleed a lot.
In article <[email protected]>,
"Wilson Lamb" <[email protected]> wrote:
> He probably means he wants to nose the piece...rounding from both sides, so
> there's no place for the bearing to run on the second pass.
> Wilson
ahhh..indeed.
In article <[email protected]>,
"Ron" <[email protected]> wrote:
> Afternoon all,
>
> I need to round over the edge of a piece of 3/4" ROak with a 9" dia.
>
> Is there an easy and safe way to do this on a router table. I could place a
> pin
> (bolt) in the router table about 2" from the bit and use it as a guide, but,
> not sure if
> that's a good idea or not. Any thoughts on this method?
>
> Or is it better to secure it to a larger piece of wood and use a handheld
> router?
> Problem here is 'hiding' the holes on the top (good) side.
> Would carpet tape hold it in place well enough?
>
> Any suggestions would be appreciated,
> Ron
>
>
Is there a reason you can't use a round-over bit with a bearing?
In that case a table would be sufficiently safe to use.
http://www.carbide.com/catalog/RBits_Radius.cfm?GroupID=0201.02.01