14" Band Saw advice

Michael Faurot wrote:

> So, going to your local Harbor Freight to get a better look at their
> line of bandsaws could well be a wasted trip.
>

I have the HF 14" saw and am satisfied with it. It could be that the
blade guides were not left off the floor model but had been pinched.
Mine came with guides and a fairly sturdy (stamped steel) base. I
installed the riser kit (for a pittance) and feel that I got, at the
very least, my moneys worth.

It isn't a top end saw. It is no more than a mid-range saw. But I cut
hardwoods and wet woods with it just fine. My only real complaint is
that the dust collection leaves a little to be desired and I think that,
if I ever get into some heavy duty use of it I'll want to pop for a
stronger motor.

I got what I paid for. Plus a little.

Bill
--
I'm not not at the above address.
http://nmwoodworks.com

Rich <[email protected]> wrote:

> My father lives in central PA not far from the grizzly warehouse so
> that is a possibility for me to eliminate shipping cost. I like the
> Jet and Delta too, but thought the same as you about Delta. You pay
> for a name as well as a product. I'll have to give the Jet another
> look.

It's been awhile since I looked at the 14" saws from Jet and Delta,
but one thing I do remember that I noticed about *some* of the 14"
models from one or both of these companies is there's a few models
that do not have a quick tension release. If the saw does not have
a quick release, it means you're going to have to crank a knob or
hand wheel every time you start using the saw and keep track of the
number of turns. When you're done using it for the day, turn the
knob/hand wheel the opposite way and number of turns to release the
tension. That's a tedium I decided I did not want to be bothered
with.

The Grizzly G0555 has a quick release and it was this feature that
made it a deal clincher for me.

--

If you want to reply via email, change the obvious words to numbers and
remove ".invalid".

Rich,

"Rich" <[email protected]> wrote
> Michael,
> Thanks for the input. You are the only one who actually addressed my OP.
> Maybe I didn't state what I was looking for clearly.
>
> I am looking for a 14" band saw with a cast frame and the ability to add a
> riser in the future. Everyone seems to think for some reason that I'm
> interested in the saws in the article in FWW.

> I read the article if I had that kind of cash, . . . SNIP

I understand your dilemma. Allow me to make a few comments about my
experience, before suggesting a solution.

I agonized literally for YEARS over the necessity & expenditure for a
bandsaw. There was no way I could justify the 'top of the line' saws, or
even the 'middle of the road' ones. I read books, magazine articles, 'THIS'
forum, etc. At the time there was also a chain of *woodworking crafts* shops
that opened a store in my area. Really known for their 'catalog sales',
don't remember their name, but the 'house brand' was 'Reliant'. 'Haunted'
that shop . . got a lot of hand-tools & supplies there, plus they carried
Delta & JET as well as the Reliant line. I was therefore able to see at
least three saws, side-by-side.

First, my background is engineering, and I am a wooden boat builder. I know
from experience that 'Finishing' may only use about 5 percent of the total
materials, it may account for 50 percent of the time, and cost, of building
or manufacture. Therefore, regarding 'Fit & Finish' . . . while 'fit' may be
an indicator of the amount of care, attention to detail, and precision of
manufacture, 'finish' is much more subjective. With one company it may
indicate poor quality throughout, while with another it may indicate a
decision to put cost & time where it will add to performance & value to the
customer. Also, my greatest peeve is Corporate 'slight-of-hand' - where they
promote an a well-known 'American' image, {& cost} and the product is 'Made
in China' for a pittance.

Second, how are you going to use this saw? Occasionally, with a bit of
re-sawing . . . as in my case. Or almost continuous use to re-saw logs &
'slabs' of hardwoods.

Third, be very aware that this is a heavy piece of equipment, moving a VERY
sharp and FAST moving cutting edge, under a good bit of tension.

The 'Final Contenders' . . .
The DELTA had the 'advertising budget' and a very nice finish. A reputation
of an 'All American' brand. The fit seemed good and it was a basic saw with
the usual 'hype' about it's adjustments. Price was at the high end.

The JET had no TV commercials or sponsored any shows, and had a similar
finish to the Delta. Fit seemed just as good as Delta. No prominent mention
of Country of Manufacture, but research indicates Taiwan under careful
{on-site?} American 'spec' control. Price - very much below Delta. Fence &
Gauge - 'optional'.

'Reliant' . . . Only seen here & in their catalog. An ugly 'Green' in color
{intentionally similar to the Grizzly ??}, and relatively poor finish. Fit
was 'fair'. Fence, Gauge, and 'extras' included. Blade guide blocks - metal
{I think}. Chinese manufacture and REALLY cheap pricing. While this Company
seems to have disappeared - I was really disappointed when the local Store
went - almost all of their house-brand 'stationary tools' have been
supplanted by ones from Harbor Freight. Probably from the same Chinese
factory. In fact, an 'HF' store has opened about 30 minutes away.

MY RESULT . . . I bought the JET 14in OPEN STAND. From Amazon, on 'Special',
plus Fence, Gauge, and Shipping, included. {I should have bought the 'Height
Block' then, but didn't. Recently had to really search around to find one at
MY price}. While the Grizzly was about the same quality as the Jet {from
Catalog description and individual comments, I'd never seen one}but at a
lower initial cost. By the time Freight and Taxes {there is *one* outlet in
PA . . . about in the middle of the state !!}were factored in, it was more.

CONCLUSION . . . SHOP for a JET. However, IF you MUST 'go cheap' look at the
Harbor Freight offering. Just keep in mind the caveats, and try to
physically LOOK at one before you buy.

Regards & Good Luck,
Ron Magen
Backyard Boatshop

Ron Magen <[email protected]> wrote:

> CONCLUSION . . . SHOP for a JET. However, IF you MUST 'go cheap' look at the
> Harbor Freight offering. Just keep in mind the caveats, and try to
> physically LOOK at one before you buy.

I've been to a number of Harbor Freight stores in several different
states. In almost every one of them, looking at the big stationary
power tools can be difficult. Either the item on the floor has
been badly abused by idiot customers or whoever put the thing
together left off parts because they were too lazy to be bothered.
I mention this specifically because, at one point I was looking at
the bandsaw Harbor Freight sells. In several of the stores, I
noticed there were *no* upper or lower blade guides on the saw. I
suspect this is a case of lazy employees, but to me it was a clear
sign to avoid these things.

So, going to your local Harbor Freight to get a better look at their
line of bandsaws could well be a wasted trip.

--

If you want to reply via email, change the obvious words to numbers and
remove ".invalid".

"dpb" <[email protected]> wrote in message news:[email protected]...
> Rich wrote:
>> I've got the article. I'm not looking to go to that level though. I want
>> to keep it a bit lower cost. But thanks for the advice. I agree about the
>> x model and the power. It also has a bigger table, beefier base and
>> construction as well as a better fence. Just wondering if anone could
>> shed light on another manufacturer's product that is comparable, like
>> Rikon, Jet or Delta etc.
>
> Well, there were Jet and Delta units included in the FWW review -- Delta
> was one of the higher-priced but about the worst performer. The Jet
> performed well w/ the exception of one test -- it was the lowest-powered
> and the weighted-sled resaw test bogged it down at the higher weight.
> Note, however, that at the lower weight it was as fast as any.
>
> Don't know about Rikon -- never seen anything of theirs except in the
> magazine pictures...
>
>
I have a Jet and after I added an Iturra tension spring and started using BC
saw blades (1/2" 3 tpi skip tooth) and use moderate tension on the blade,
I've had no trouble resawing. I have the riser block installed. I aligned
the top wheel.

I'm of the opinion that you will probably have to tune any saw you buy. I'd
buy the one that I liked. That's what I did.

Rich, Mike, et al . . .

Rich -
You are very welcome. Just remember it is MY OPINION and act
accordingly.

Actually, 'born & raised' in Atlantic City, NJ. A Rhode Island 'wannabe'
since I got to know, and sailed with, a gentleman from the Narragansett Bay
area - he sails a Pearson 28, hull #4 !!

Shipping is most certainly a big factor that many people inadvertently
ignore. If memory serves, the Grizzly 'rate' was about $70. Adding 'insult
to
injury' was another $30 or so in TAX. It wasn't so much that I *liked* the
JET or Delta 'better' {I thought of them more as 'equivalent'}, but the
OVERALL total outlay was less.

Agreed, about the HF stuff. Over the years I've gotten a LOT of stuff from
them. Starting with the really *simple* stuff . . . {'A boatbuilder can
never have too many clamps !!'} Wooden 'Carpenters Clamps' are wooden
carpenters clamps, are wooden . . etc, etc.. Theirs for $3.00 or Jorgensen
for $10 ???. From there I graduated to small power tools - that I considered
'disposable' at the price - that I could 'dedicate' - rather then spend time
'swapping out' fittings. 4-1/2 in 'Angle Grinders' for $10 !! . Have 2-3 on
hand with different set-up, grinding, cutting, detail sanding, etc. 'Trim'
router for $20 . . . have one dedicated to a special extra large base. {In
fact, my neighbor - a building contractor - looked at my 'stuff', had me
take him over to the 'local outlet, and got one just to set-up for routing
door hinges !! He also 'signed-up' for the 'Flyers' and catalog!!} My
point - and mention of 'caveats was that YOU mentioned the money concerns. I
think the HF product is about the cheapest one can go. Just be warned of the
DANGER of this tool, in general, and how much that will increase if VERY
POORLY made.

MIKE - in the same vein - I wouldn't consider it a 'waste of time' to be
able to examine one for 'fit' and 'structural integrity'. Small fittings &
'knobs' that have been left off or 'gown legs' is not a specific concern.
Having a copy of the 'Assembly / Instruction' Manual will determine if these
parts come with the unit, and how they are arranged. Being able to see how
heavy castings fit, the way motor mounts are aligned & adjusted, the blade
wheel adjustment, etc - is of more importance.

As far as 'dust collection' is concerned . . from what I've read they
almost all really stink !! It's simply due to the way they work. If
'aftermarket' modified - commercially or shop-made - to really enclose the
exposed control & adjustment areas, then the air movement & dust capture
would be improved.

Regards & Good Luck,
Ron Magen
Backyard Boatshop


"Rich" <[email protected]> wrote
> Ron,
> Thanks for the great advice.
> With an email address like yours, you must be from New England also. Rhode
Islander transplanted here via the Navy.
SNIP
not far from the grizzly warehouse so that is a possibility for me to
eliminate shipping cost. I like the Jet and Delta too,
SNIP
As far as harbor freight stuff goes, I steer well clear of them unless I'm
going to buy a "single use" tool from them.

Michael,
Thanks for the input. You are the only one who actually addressed my OP.
Maybe I didn't state what I was looking for clearly.

I am looking for a 14" band saw with a cast frame and the ability to add a
riser in the future. Everyone seems to think for some reason that I'm
interested in the saws in the article in FWW.
I read the article if I had that kind of cash, I'd buy the Rikon or Grizz.
but......I was asking about a step down from the ones in the article. The
saws in the article all have steel frames. While that is better than a cast
frame, I don't have that kind of money.

I do appreciate everyone's input but I'm not really getting much feedback on
what I am looking for.

--
Rich Harris

I've got the article. I'm not looking to go to that level though. I want to
keep it a bit lower cost. But thanks for the advice. I agree about the x
model and the power. It also has a bigger table, beefier base and
construction as well as a better fence. Just wondering if anone could shed
light on another manufacturer's product that is comparable, like Rikon, Jet
or Delta etc.

--
Rich Harris

.
"Ralph E Lindberg" <[email protected]> wrote in message
news:[email protected]...
> In article <GPoBi.2178$Pa5.1833@trndny09>,
> "Rich" <[email protected]> wrote:
>
>> Finally got the green light for a band saw. (Come up with a project that
>> requires one and you are in business) I've been looking at either the new
>> Grizzly G0555x or the G0555. I'm leaning towards the x model seems to be
>> heavier built. Any advice or recomendations for either of those or
>> something
>> else in that class of saw? Thanks for the advice in advance.
>
> FWW did a review of 14 inch in their last issue. The G0457 got their
> best value (I own one, the down-side is custom blades). Of the two you
> list I would get the G0555X (MORE POWER)
>
> --
> --------------------------------------------------------
> Personal e-mail is the n7bsn but at amsat.org
> This posting address is a spam-trap and seldom read
> RV and Camping FAQ can be found at
> http://www.ralphandellen.us/rv

Leuf,
Thanks for the help. I checked out the rigid also. Thought it would be alot
of bang for the buck, but I found out there alot of complaints about
balancing and tracking of the blade. I realize you have to set up a saw in
the beginning but it seems like there alot of people out there who have been
having alot of difficulty.
Rich

Ron,
Thanks for the great advice.
With an email address like yours, you must be from New England also. Rhode
Islander transplanted here via the Navy.
I'll be using my band saw in much the same manner as you. As a matter of
fact, I'll be building a boat in the not too distant future. My father lives
in central PA not far from the grizzly warehouse so that is a possibility
for me to eliminate shipping cost. I like the Jet and Delta too, but thought
the same as you about Delta. You pay for a name as well as a product. I'll
have to give the Jet another look. As far as harbor freight stuff goes, I
steer well clear of them unless I'm going to buy a "single use" tool from
them.
With your permission I'd like to stay in touch regarding buiding a boat. I'l
send you an email via my hotmail addy if its ok.

Rich

"Ron Magen" <[email protected]> wrote in news:3aYBi.16$h06.6@trnddc03:

> Rich,
>
> "Rich" <[email protected]> wrote
>> Michael,
>> Thanks for the input. You are the only one who actually addressed my
>> OP. Maybe I didn't state what I was looking for clearly.
>>
>> I am looking for a 14" band saw with a cast frame and the ability to
>> add a riser in the future. Everyone seems to think for some reason
>> that I'm interested in the saws in the article in FWW.
>
>> I read the article if I had that kind of cash, . . . SNIP
>
> I understand your dilemma. Allow me to make a few comments about my
> experience, before suggesting a solution.
>
> I agonized literally for YEARS over the necessity & expenditure for a
> bandsaw. There was no way I could justify the 'top of the line' saws,
> or even the 'middle of the road' ones. I read books, magazine
> articles, 'THIS' forum, etc. At the time there was also a chain of
> *woodworking crafts* shops that opened a store in my area. Really
> known for their 'catalog sales', don't remember their name, but the
> 'house brand' was 'Reliant'. 'Haunted' that shop . . got a lot of
> hand-tools & supplies there, plus they carried Delta & JET as well as
> the Reliant line. I was therefore able to see at least three saws,
> side-by-side.
>
> First, my background is engineering, and I am a wooden boat builder. I
> know from experience that 'Finishing' may only use about 5 percent of
> the total materials, it may account for 50 percent of the time, and
> cost, of building or manufacture. Therefore, regarding 'Fit & Finish'
> . . . while 'fit' may be an indicator of the amount of care, attention
> to detail, and precision of manufacture, 'finish' is much more
> subjective. With one company it may indicate poor quality throughout,
> while with another it may indicate a decision to put cost & time where
> it will add to performance & value to the customer. Also, my greatest
> peeve is Corporate 'slight-of-hand' - where they promote an a
> well-known 'American' image, {& cost} and the product is 'Made in
> China' for a pittance.
>
> Second, how are you going to use this saw? Occasionally, with a bit of
> re-sawing . . . as in my case. Or almost continuous use to re-saw logs
> & 'slabs' of hardwoods.
>
> Third, be very aware that this is a heavy piece of equipment, moving a
> VERY sharp and FAST moving cutting edge, under a good bit of tension.
>
> The 'Final Contenders' . . .
> The DELTA had the 'advertising budget' and a very nice finish. A
> reputation of an 'All American' brand. The fit seemed good and it was
> a basic saw with the usual 'hype' about it's adjustments. Price was at
> the high end.
>
> The JET had no TV commercials or sponsored any shows, and had a
> similar finish to the Delta. Fit seemed just as good as Delta. No
> prominent mention of Country of Manufacture, but research indicates
> Taiwan under careful {on-site?} American 'spec' control. Price - very
> much below Delta. Fence & Gauge - 'optional'.
>
> 'Reliant' . . . Only seen here & in their catalog. An ugly 'Green' in
> color {intentionally similar to the Grizzly ??}, and relatively poor
> finish. Fit was 'fair'. Fence, Gauge, and 'extras' included. Blade
> guide blocks - metal {I think}. Chinese manufacture and REALLY cheap
> pricing. While this Company seems to have disappeared - I was really
> disappointed when the local Store went - almost all of their
> house-brand 'stationary tools' have been supplanted by ones from
> Harbor Freight. Probably from the same Chinese factory. In fact, an
> 'HF' store has opened about 30 minutes away.
>
> MY RESULT . . . I bought the JET 14in OPEN STAND. From Amazon, on
> 'Special', plus Fence, Gauge, and Shipping, included. {I should have
> bought the 'Height Block' then, but didn't. Recently had to really
> search around to find one at MY price}. While the Grizzly was about
> the same quality as the Jet {from Catalog description and individual
> comments, I'd never seen one}but at a lower initial cost. By the time
> Freight and Taxes {there is *one* outlet in PA . . . about in the
> middle of the state !!}were factored in, it was more.
>
> CONCLUSION . . . SHOP for a JET. However, IF you MUST 'go cheap' look
> at the Harbor Freight offering. Just keep in mind the caveats, and try
> to physically LOOK at one before you buy.
>
> Regards & Good Luck,
> Ron Magen
> Backyard Boatshop
>
>
>
>
>

Ron

Just a few observations to add to your conclusions. The store you are
referring to was Wood Workers Warehouse which went bankrupt about three
or four years ago after bad business decisions by their parent company. I
seem to buy most of my machines used and have a few Reliant (dust
collector and shaper). They are real reasonable used since there is no
longer any support for them, so you take a chance if parts are needed but
you are correct generic Chinese parts seem to fit most times.

I also own some Jet, bought used. The 14" BS has a riser, Carter roller
guides, and an after market fence similar to the Kreg all of which came
with it. It is the older "blue Jet" rather than the white. Recently I
cracked the pivot arm on the upper slider bracket. I immediately called
Louis Iturra for an after market replacement. (Louis is a great guy who
is the maven of band saws - call 866-883-8064 for his excellent catalog
by mail). Louis explained that the aluminum casting of this slider
frequently breaks on the older Jets and they beefed it up on the newer
ones. He sells a beefier replacement for the Delta 14" which the Jet is a
copy of. He said that the Jet, however, uses a cheaper one way press
fitting of this assembly making disassembly impossible. Therefore, the
only solution is to buy the entire assembly directly from Jet. So two
weeks and $65 later the part arrived and seems beefier. Jet took a week
and a half to send the part, although their customer service were
pleasant and helpful when I called to check.

The original casting of the Jet part had some voids in it, hence the
failure. My machines are from Taiwan and I'm not overly impressed with
their castings. Worse, however, seem to be the Harbor Freight machines
which are almost direct copies of the Jet and made in mainland China.
The HF 1236 lathe knockoff in their store shows several casting cracks
and flaws compared to my Jet 1236. HF quality is just too much of a crap
shoot for me. That said, I just bought a HF Chinese knockoff of a
pneumatic carving tool that was 7X less expensive than the Taiwanese tool
it was copied off at Woodcraft - talk about markup! For something like
that I can buy six more and toss them if they break compared to
Woodcraft. You don't really do that with bandsaws, however.

So if you listen to Louis, you look for used Delta or Rockwell bandsaws
to refurbish. I now have an old Rockwell 14" metal cutting saw that I got
for under $50 which is beat to hell and has a 3 phase motor. This winter
I'll be trying a refurb. Completed it won't save me any money compared to
the used Jet, but you can readily see the better quality.

Hope these observations help, obviously I'm a fan of waiting for used to
show up.

Jerry

--
Posted via a free Usenet account from http://www.teranews.com

Jerry,

Thanks for the reminder.

Already know about Louis . . . gotten a few things from him already . . .
plus the catalog is a nice read, anyway.

Agreed, getting a 'used but not abused . .' piece of equipment at a 'dirt
cheap price' is a very good way to go. However it is VERY dependent on {at
least} TWO things . . . a} the *availability* of the equipment in YOUR area
and b} YOUR level of 'mechanical skill' and *knowledge* of the equipment
i.e. 'DIRT' may be the operative word in the pricing. While it was one of
the avenues I explored, there was nothing in the local area - not even
'commercial' sized equipment. The likelihood that any would surface if I
waited was slim to none.

However, I did some *serious* shopping and got a good deal. As I said, in
hindsight I should have gotten the Riser {for future use}at the same time &
level of discount. While I didn't, and the price had gone up a great deal in
the interim, a bit of *serious searching* got me an 'new-in-the-box' used
one for less then that original price. But I WAS lucky.

We all have to make choices that are within our own abilities, budget, and
needs. All I'm saying is to look at ALL your options before putting your
hand in your pocket.

Regards,
Ron Magen
Backyard Boatshop

"A Lurker" <[email protected]> wrote
> "Ron Magen" <[email protected]> wrote >
> > "Rich" <[email protected]> wrote
> Ron
>
> Just a few observations to add to your conclusions. The store you are
> referring to was Wood Workers Warehouse which went bankrupt about three
> or four years ago after bad business decisions by their parent company.
SNIP
> So if you listen to Louis, you look for used Delta or Rockwell bandsaws
> to refurbish. SNIP
Completed it won't save me any money compared to the used Jet, but you can
readily see the better quality.
>
> obviously I'm a fan of waiting for used to show up.
>
> Jerry

Rich <[email protected]> wrote:

> Finally got the green light for a band saw. (Come up with a project
> that requires one and you are in business) I've been looking at either
> the new Grizzly G0555x or the G0555. I'm leaning towards the x model
> seems to be heavier built. Any advice or recomendations for either of
> those or something else in that class of saw? Thanks for the advice in
> advance.

I bought the G0555 about a year ago and have found it to be a good
saw. At the time, the G0555X was not out, so that wasn't an option
for me. If I was looking today, I'd be trying to decide between
the G0555X and the G0555 as well. But if the G0555X wasn't available,
I'd buy the G0555 again.

Awhile back, I looked at what was different on the G0555X vs. the
G0555. The main things that I remember is the G0555X has a more
powerful motor (1.5 HP), the wheels are cast iron or steel and it
comes with the re-saw fence. With my G0555, I can't say that I've
ever found its 1 HP motor lacking for any of the re-saw stuff I've
done. My saw also cuts straight so I guess I'm doing just fine with
aluminum wheels. I did buy, as an extra, the re-saw fence and that
has been well worth the extra expense.

I also bought the riser block, but have yet to install it. So far I
haven't needed to re-saw anything larger than 6". I don't know if I'll
ever install it, but I'm glad it's there if I ever do decide I need to
re-saw something bigger.

As with any saw, it works best with a good blade. Lately I've been
using the Olson blades available from Ballew[1]. These blades are
relatively inexpensive and they cut well.


[1]: http://www.ballewsawandtool.com/shop/band-saw-blades.html

--

If you want to reply via email, change the obvious words to numbers and
remove ".invalid".

Rich wrote:
> I've got the article. I'm not looking to go to that level though. I want to
> keep it a bit lower cost. But thanks for the advice. I agree about the x
> model and the power. It also has a bigger table, beefier base and
> construction as well as a better fence. Just wondering if anone could shed
> light on another manufacturer's product that is comparable, like Rikon, Jet
> or Delta etc.

Well, there were Jet and Delta units included in the FWW review -- Delta
was one of the higher-priced but about the worst performer. The Jet
performed well w/ the exception of one test -- it was the lowest-powered
and the weighted-sled resaw test bogged it down at the higher weight.
Note, however, that at the lower weight it was as fast as any.

Don't know about Rikon -- never seen anything of theirs except in the
magazine pictures...

--

Lowell Holmes wrote:
...
> I have a Jet and after I added an Iturra tension spring and started using BC
> saw blades (1/2" 3 tpi skip tooth) and use moderate tension on the blade,
> I've had no trouble resawing. I have the riser block installed. I aligned
> the top wheel.
>
> I'm of the opinion that you will probably have to tune any saw you buy. I'd
> buy the one that I liked. That's what I did.

The FWW review noted (as I did) that the Jet resaw was as good as any
(even the 3x the price General or 2x the price Laguna "best overall") in
performance except under the heavier load. That wasn't a fault of the
saw so much as that the model tested had the smallest motor of any in
the test. The tests were all done w/ the same 3 tpi 1/2" blade.

Of _course_ one would tune any saw one buys...

--

On Fri, 31 Aug 2007 18:18:29 GMT, "Rich" <[email protected]>
wrote:

>Leuf,
>Thanks for the help. I checked out the rigid also. Thought it would be alot
>of bang for the buck, but I found out there alot of complaints about
>balancing and tracking of the blade. I realize you have to set up a saw in
>the beginning but it seems like there alot of people out there who have been
>having alot of difficulty.
>Rich

I think that home depot is going to get a higher percentage of people
who know nothing about setting up the saw and just expect it to work,
so I'd read the complaints with a grain of salt. It seems to have a
decent reputation on this group, IIRC.

FWIW, I bought the 1 hp Delta closed stand model and have been
battling a vibration problem myself. Still haven't quite figured it
out. The upper wheel seems pretty well balanced but is slightly out
of round (about .02"). I thought maybe it was the blade because it
seemed to get much worse recently, but a blade change didn't help.
Then I took the blade off and checked the balancing of the wheel, put
the blade back on and it was apparently back to its normal amount of
vibration. It may be how the wheels are balanced that how they are
oriented to each other is affecting the dynamic balancing. I intend
to put some marks on the wheels and test that theory. But I digress.
My point was you can get vibration with any saw, especially in this
price bracket. At least with home depot you can pack the thing back
up and bring it back yourself (with some help from a buddy) if all
else fails. I have dealt with Grizzly CS and they are very good about
sending you out replacement parts. However the quality contol of the
replacement parts doesn't seem any better than for what comes in the
box.

One other thing about the Ridgid, you can put their mobile base on the
stand which allows the stand to still sit on the floor when it's down.
Press the foot pedal and it lifts it up. MUCH better than the POS
Delta stand mine is on, and the vibration definitely got worse with
it. Even if I stick shims under it it's still worse.


-Leuf

On Fri, 31 Aug 2007 13:37:09 GMT, "Rich" <[email protected]>
wrote:

>Michael,
>Thanks for the input. You are the only one who actually addressed my OP.
>Maybe I didn't state what I was looking for clearly.
>
>I am looking for a 14" band saw with a cast frame and the ability to add a
>riser in the future. Everyone seems to think for some reason that I'm
>interested in the saws in the article in FWW.
>I read the article if I had that kind of cash, I'd buy the Rikon or Grizz.
>but......I was asking about a step down from the ones in the article. The
>saws in the article all have steel frames. While that is better than a cast
>frame, I don't have that kind of money.
>
>I do appreciate everyone's input but I'm not really getting much feedback on
>what I am looking for.

The frames of the 14" saws you are looking at are essentially
identical. In fact you can take the riser block from most any
manufacturer and put it on just about any saw.

One big difference between Grizzly and the others is the way the motor
is mounted. Grizzly bolts theirs to the saw itself. Everyone else
either hangs it below inside the stand or has it on the stand behind
the saw, and uses the standard NEMA frame. That way you can slap any
motor you want on there at a later date. I don't think you can do
that with Grizzly.

So one option you might consider if you don't think you really need
the riser block but want to keep your options open just in case, is go
for something like the Ridgid which by the time you factor in shipping
is your cheapest option. The 3/4 hp motor should be fine without the
riser. Then you have three routes you can take. Stay with what
you've got, get the riser and a 1-1/2 hp motor, or get a larger/better
saw. You've put in a minimal investment at the beginning so you keep
your options open.

I tend to think strapping all the goodies onto the 14" saws is more of
a cash cow for the manufacturers than a huge improvement over the more
basic 14" saws. You'll get more for your money going to a larger saw.


-Leuf

On Sun, 02 Sep 2007 04:17:28 -0400, BillinDetroit <[email protected]>
wrote:

>Michael Faurot wrote:
>
>> So, going to your local Harbor Freight to get a better look at their
>> line of bandsaws could well be a wasted trip.
>>
>
>I have the HF 14" saw and am satisfied with it. It could be that the
>blade guides were not left off the floor model but had been pinched.
>Mine came with guides and a fairly sturdy (stamped steel) base. I
>installed the riser kit (for a pittance) and feel that I got, at the
>very least, my moneys worth.
>
>It isn't a top end saw. It is no more than a mid-range saw. But I cut
>hardwoods and wet woods with it just fine. My only real complaint is
>that the dust collection leaves a little to be desired and I think that,
>if I ever get into some heavy duty use of it I'll want to pop for a
>stronger motor.
>
>I got what I paid for. Plus a little.
>
>Bill

I have the ridgid/grizzly/chi-wan-ese BS and the dust collection is a joke..
little bitty connector under the table at the top of the clam shell..

I cut a 4" hole in the lower door and put a DC fitting on it, plugged up the
square hole from the original port and Y'd a 2.5" hose to as close to the bottom
of the zero clearance insert as I could.. works great, if I remember to
open/close the proper blast gates.. lol

I've read several complaints about the HF BS and suspect most are cured by
putting a real blade on it...
That, a tune up and some cool blocks should make it a very serviceable saw, for
the money..



mac

Please remove splinters before emailing

In article <GPoBi.2178$Pa5.1833@trndny09>,
"Rich" <[email protected]> wrote:

> Finally got the green light for a band saw. (Come up with a project that
> requires one and you are in business) I've been looking at either the new
> Grizzly G0555x or the G0555. I'm leaning towards the x model seems to be
> heavier built. Any advice or recomendations for either of those or something
> else in that class of saw? Thanks for the advice in advance.

FWW did a review of 14 inch in their last issue. The G0457 got their
best value (I own one, the down-side is custom blades). Of the two you
list I would get the G0555X (MORE POWER)

--
--------------------------------------------------------
Personal e-mail is the n7bsn but at amsat.org
This posting address is a spam-trap and seldom read
RV and Camping FAQ can be found at
http://www.ralphandellen.us/rv

On Thu, 30 Aug 2007 13:55:49 +0000, Rich wrote:

> I've got the article. I'm not looking to go to that level though. I want to
> keep it a bit lower cost. But thanks for the advice. I agree about the x
> model and the power. It also has a bigger table, beefier base and
> construction as well as a better fence. Just wondering if anone could shed
> light on another manufacturer's product that is comparable, like Rikon, Jet
> or Delta etc.

I bought the deluxe 14" Rikon with 13" resaw capabilities. I haven't used
it yet for fine work, but I've done quite a bit of resaw, mainly cutting
green hardwood logs for turning blocks. I'm happy. The two speeds are
nice - the low speed is really good for resaw.

I did have a problem when I got it with the table not being flat. Nobody
ages their cast iron anymore, so it could have happened on any saw in that
price range. But the point is I sent them an email one evening about the
table and got one back the next morning saying they'd send me a new table.
The new table was very flat! So I think their customer service is pretty
good.

Note: some of the high end vendors like General in Canada still do
age their castings, but nobody in the price range you're talking about.