It's been a long time since I tuned my jointer. Today, I noticed some "fla=
t spots" on the knives. I removed and sharpened them using the scary sharp=
method and a Lee Valley blade holder for doing this. They are now sharp, b=
ut I didn't try to get them razor sharp because they won't hold that edge w=
hen jointing wood.
I installed the knives so that the difference in height across a blade is =
about .002 in. I then adjusted the blades so that the max difference for t=
he 3 blades as they rotated on the cutter head was about .003 inches. =20
I then set the height of the tables and ran a test board of kiln dried popl=
ar through. I does create a flat board, but I always listen for the sound =
of a machine as it runs. It sounds like the wood chipper I use when mulchi=
ng garden and tree stuff in the Fall. The cutting depth was slightly less =
than 1/16 inch.
Is the jointer ok or,are the blades not sharp enough or, are the adjust=
ment tolerances too generous?
Len
On 5/22/2014 4:22 PM, Len wrote:
> Is the jointer ok or,are the blades not sharp enough or, are the adjustment tolerances too generous?
Sharpness is relative, and would be my first inclination to check. Did
it make the same noise with the stock running in either direction?
Did you try decreasing the cutting depth? Around 1/16" is a strong cut,
depending upon the stock.
I'm with you on the sound of things running, but the proof is in the
pudding and the state of the surface of the face/edge you joined should
tell the tale, and be the judge.
If reaches the standard you want in a "freshly jointed" edge,
particularly on stock with some grain changes. A bit of noise (without
smoke <g>) would not concern me all that much as long as the jointed
surface needs no further work/milling/sanding, etc.
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
On Thursday, May 22, 2014 4:22:43 PM UTC-5, Len wrote:
> It's been a long time since I tuned my jointer. Today, I noticed some "f=
lat spots" on the knives. I removed and sharpened them using the scary sha=
rp method and a Lee Valley blade holder for doing this. They are now sharp,=
but I didn't try to get them razor sharp because they won't hold that edge=
when jointing wood.
>=20
>=20
>=20
> I installed the knives so that the difference in height across a blade i=
s about .002 in. I then adjusted the blades so that the max difference for=
the 3 blades as they rotated on the cutter head was about .003 inches. =20
>=20
>=20
>=20
> I then set the height of the tables and ran a test board of kiln dried po=
plar through. I does create a flat board, but I always listen for the soun=
d of a machine as it runs. It sounds like the wood chipper I use when mulc=
hing garden and tree stuff in the Fall. The cutting depth was slightly les=
s than 1/16 inch.
>=20
>=20
>=20
> Is the jointer ok or,are the blades not sharp enough or, are the adju=
stment tolerances too generous?
>=20
>=20
>=20
> Len
Problem solved. One of the knives moved when I tightened it and was up =
tooo high. It was doing all the work. After an hour of fiddling it sounds=
jusssst right!
=20
Thanks for all the suggestions
Len
On 5/22/2014 4:22 PM, Len wrote:
...
"flat spots" on the knives. I removed and sharpened them using the scary
...
> I installed the knives so that the difference in height across a
> blade is about .002 in. I then adjusted the blades so that the max
> difference for the 3 blades as they rotated on the cutter head was
> about .003 inches.
>
> I then set the height of the tables and ran a test board of kiln
> dried poplar through. I does create a flat board, but I always listen for the
> sound of a machine as it runs. It sounds like the wood chipper I use
> when mulching garden and tree stuff in the Fall. The cutting depth was
> slightly less than 1/16 inch.
>
> Is the jointer ok or,are the blades not sharp enough or, are the
adjustment tolerances too generous?
I've gone to using a homemade jig w/ a set of magnets so I can't say
just how close they would mic but I'd think the heights would be better
than 3-thou a little.
I'm wondering w/ that kind of noise description--you didn't reverse them
by any chance and got wrong bevel side up?
--