On 3 Jun 2005 17:53:41 -0400, [email protected] (DoN. Nichols) wrote:
> The "jet mirror" -- is that mounted in a ring into which turbine
>blades dovetail? Ir is it a ring gear of some sort?
That's one of the little ones. I've made several.
That particular one is just a knife-edge seal - the diagonal bars round
the edge hold it in place and there are a couple of sharp rings on the
inside edge to form the seal. Some of the others are "stator" rings -
static vanes at the end of the compresor stage.
http://codesmiths.com/shed/mirrors/
(new selling site is under development - visit the market stall if
you're in Bristol)
In article <[email protected]>,
R.H. <[email protected]> wrote:
>Another set has just been posted:
>
>http://puzzlephotos.blogspot.com/
>
>
>Rob
>
>
363. One set of magic words is "split-image rangefinder".
More probably, the OP is thinking of "beam splitter".
364.
365. a *LOUSY* picture of a campo.
366. the rack and pinion section of a lever-handle cork screw.
367. finger pulse-rate monitor
368. at first glance it looks like a home-made drive gear
replacement for an electric can-opener, but it can't be that.
(the screw-head and rubber grommet would keep the can from contacting
the drive gear.)
doesn't appear to be a 'slot cutter', the 'teeth' are way too irregular
for that.
By elimination it has to be a sex aid for when a rhinoceros mates with
an elephant. "ele-phino"
369. second lousiest picture of the week.
squeezing or crimping tool of some sort
R.H. <[email protected]> wrote:
> http://puzzlephotos.blogspot.com/
#363: Periscope? No.
#364: tip of a umbrella
#365: Capotasta (SP) used for guitars (tuning)
#366: Cork puller. Italian style, made in millions
#367: Sensor for heart beat rate (clamped on finger)
#368: Well, he needed a sawblade that will not cut.
So he abused a good one until it suited.
#369: Tool for widening tubes
Nick (this time I got it right with the numbers :-))
--
"Wissenschafts"-Sendung auf einem der Privat-Kanäle:
"Der Behälter fasst 200.000 Kubik-Liter."
Wie viele Quadrat-Stunden braucht es dann wohl, um ihn voll zu bekommen?
DeepDiver wrote:
> "Julie" <[email protected]> wrote in message
> news:[email protected]...
>
>>R.H. wrote:
>>
>>>Another set has just been posted:
>>>
>>>http://puzzlephotos.blogspot.com/
>>>
>>
>>363. Hall of mirrors for mice
>>364. Washington Monument, for mice
>>365. Capatult for mice
>>366. Corkscrew
>>367. Electronic metronome
>>368. Merry-go-round for mice
>>369. Capult for mice
>
>
> Actually Julie, #369 is a Mouse Juicer (for making delicious
> freshly-squeezed-mice drinks!)
>
> ;)
>
> - Michael
>
"Mmmm.. that's great mouse:-D"
"R.H." <[email protected]> wrote in message
news:[email protected]...
> Another set has just been posted:
>
> http://puzzlephotos.blogspot.com/
>
>
> Rob
>
>
363 Periscope
364 Bullet Calibration Thing - Ring Sizing Thing?
365 Guitar Capo
366 Corkscrew
367 Chronographic Device? - Stopwatch?
368 A Screw-in cog device.
369 High leverage pliers.
matalog.
From rec.crafts.metalworking:
363 Dunno and can't wait to find out! Would have thought periscope but
that hardly seems "amazing"...
364 ?
365 Looks like a capo. The pad looks too short for a guitar so maybe for a
banjo or some special purpose for guitar.
366 Cork screw / remover
367 Pulse or O2 sensor to be placed on the finger
368 ?
369 Saw two of those at an auction Saturday but wasn't there when they
auctioned them so don't know. Looks like it's to spread something?
Best Regards,
Keith Marshall
[email protected]
"I'm not grown up enough to be so old!"
"R.H." <[email protected]> wrote in message
news:[email protected]...
> Another set has just been posted:
>
> http://puzzlephotos.blogspot.com/
>
>
> Rob
>
>
R.H. wrote:
> 365. 3-String capo
Minor clarification from the web site-- this isn't so much for "tuning"
the guitar as it is for reorienting the string configuration-- I guess
you could say that "tunes" the guitar, but I think of tuning the guitar
as making sure the pitches are accurate, sometimes using a tuning device.
Okay, to explain:
A guitar's standard open tuning is E A D G B E (low to high).
A standard (full-sized) capo, will cover all six of those strings to
produce a different base pitch. One such base pitch might be G C F Bb D
G -- this would be the effect of the capo on the 3rd fret.
The Shubb partial capo covers only three strings of the instrument,
which allows for open chords using the capo. I.e. if I place the
3-string capo on the 2nd fret, I can get E A E A C# E, which is an open
a-major chord.
Now, personally, even though I own one, I think the Shubb capo is not a
particularly good product. It might work well for some instruments, but
it doesn't for mine, so I actually made up a whole set of partial capos,
and use them for different purposes:
http://juliewaters.com/how.php
--julie
_what
> was it made FOR?_ i.e. what was that specific purpose?
I was going to leave this as a "cliffhanger" until next week, but if you
really want to know I guess I can spill it now. Here is the description
that Elijah provided to me:
"This is a saw for a depth controlled cut of plastic, specifically for
cutting open a "wall wart" without damaging the transformer inside. I needed
to resolder the output wires after they broke at the edge of the box. I put
this in the chuck of a drill press, turned it on, then moved the transformer
box around to cut it open along the existing seam."
In article <[email protected]>,
"R.H." <[email protected]> wrote:
>Another set has just been posted:
>
>http://puzzlephotos.blogspot.com/
>
>
>Rob
363. Breast enhancement goggles.
364. Person confuser.
365. 3.5 inches of pure terror. In the right context, anyway.
366. "Swiss army knife" that McGuyver's alcoholic brother, Kevin, uses
to make mixed drinks out of almost anything.
367. Fingertip shift light.
368. Screw frock. The purpose is to sound dirty.
369. Toenail clipper for people with wicked foot fungus.
Posted from RCM.
--
B.B. --I am not a goat! thegoat4 at airmail dot net
http://web2.airmail.net/thegoat4/
"R.H." <[email protected]> wrote in news:AGyne.12691$XA6.5255
@tornado.ohiordc.rr.com:
> Another set has just been posted:
>
> http://puzzlephotos.blogspot.com/
>
>
> Rob
>
>
363 - Hard to see the angles of the prisms, but if they're the right ones,
you can make an anamorphic projection lens with them.
"R.H." <[email protected]> wrote in news:AGyne.12691$XA6.5255
@tornado.ohiordc.rr.com:
#363 - Can be used to make an interferometer.
--
Dan
"R.H." <[email protected]> wrote in message
news:[email protected]...
> Another set has just been posted:
>
> http://puzzlephotos.blogspot.com/
>
>
> Rob
>
>
364. Tire Inflation Gauge
All but the first have been answered correctly, I'll go ahead and give the
answer to that one also, I usually don't get very many guesses after the
first day.
Spoilers
.
.
.
.
.
.
.
.
.
.
.
.
.
.
363. The prisms can be used to make an optical device called a pseudoscope.
I made a separate page with more info on this one:
http://pseudoscope.blogspot.com/
364. Tire gauge
365. 3-String capo
366. Corkscrew
367. Pulse monitor
368. Saw blade
369. Nutcracker
More photos and links can be found on the answer page:
http://pzphotosan67.blogspot.com/
Rob
In article <[email protected]>,
R.H. <[email protected]> wrote:
>Another set has just been posted:
>
363: Periscope
364: Pressure gauge, ancestor of the pencil-type tire gauge.
365: Clamp
366: Wing-type corkscrew, derided by "Wine for Dummies"
367: Pulse monitor
368: It's a toothed wheel with a screw through it, isolated from the
head by a rubber washer. As for what it's made for... dunno
369: Crimping tool
--
There's no such thing as a free lunch, but certain accounting practices can
result in a fully-depreciated one.
"Matalog" <[email protected]> writes:
> 367 Chronographic Device? - Stopwatch?
I think it's a sensor you place on your finger, such as one measuring
the amount of oxygen in your blood, or perhaps pulse, or blood
pressure.
> 368 A Screw-in cog device.
It might be a crude slot cutter, or else a knob.
--
Sending unsolicited commercial e-mail to this account incurs a fee of
$500 per message, and acknowledges the legality of this contract.
R.H. wrote:
>Another set has just been posted:
>
>http://puzzlephotos.blogspot.com/
>
>
>Rob
>
>
>
>
From Rec.woodworking
#363: Mirror? The prisms will bend light around a corner. So it would
act like a mirror?
#364: Hmm. Maybe a tool for security fasteners?
#365: ??
#366: Corkscrew
#367: Stopwatch / heart rate monitor?
#368: Dunno
#369: Dunno
"RAM^3" <[email protected]> wrote in message
news:[email protected]...
> "R.H." <[email protected]> wrote in message
> news:[email protected]...
>> Another set has just been posted:
>>
>> http://puzzlephotos.blogspot.com/
>>
>>
>> Rob
>>
>>
>
> 364. Tire Inflation Gauge
363 I go along with the "periscope"
364 Tire pressure gauge sounds as good as anything else.
365 Capo sounds good
366 Yup, corkscrew
367 What everyone else says
368 Damfino
369 ?? Is it supposed to be used by pulling up on the handle or pushing
down? Mounted on a board, looks like push down. Some kind of cobbler's tool?
Reminds me of a tool used for spreading battery cable terminals, but that
wouldn't be mounted like that.
--
Nahmie
The greatest headaches are those we cause ourselves.
In article <[email protected]>,
R.H. <[email protected]> wrote:
>Another set has just been posted:
>
>http://puzzlephotos.blogspot.com/
O.K. Posting from rec.crafts.metalworking again:
363) Various things could be made from one or more prisms. The one
which first pops into my mind is a simple periscope. (But a
better one than can be made with just mirrors.) I used to get
old tank periscope prisms, and pair them up as a kid. (I had a
nice surplus store in town, which I frequented.)
364) Hmm ... sort of looks like an old powder gauge. I think that
it is adjusted for capacity with the screw on the bottom, and it
may bayonet into place on a reloading press or somewhere nearby
using the two key slots in the larger hole.
365) A "capo" -- for holding the strings to a fret on a stringed
instrument like a guitar or a banjo, to allow changing keys
without having to retune everything -- or without having to
learn alternate fingerings to play in another key. I think that
this one must be for a banjo, as it does not appear to be wide
enough to get all of the strings on a guitar. (And even if it
is used on a 5-string banjo, it only needs to cover the first
four -- the fifth starts at a different place, and may have a
sliding equivalent for just that one string bolted to the neck.
366) A "winged" corkscrew. The gears on the sides are rotated by
pressing the wings down, and they engage the square slots in the
shaft leading to the corkscrew, pulling it up.
367) This one looks to me like a pulse rate monitor -- perhaps worn
by a walker or a jogger. It apparently has a choice of audio
output (beeps, I guess), or a readout on the display -- and an
ability to measure time as well. The spring on the back goes
around a finger, with the finger resting in the contoured
groove, and the little pair of rectangles measuring the pulse,
either by IR or electrical contacts.
368) It is either a makeshift circular saw (tiny) or a milling
cutter. I hope that there are *two* nuts on the other side, or
it will unscrew if chucked in a normal drill motor (electric
drill). And the teeth are not oriented to use one in reverse
which would tighten the nut.
That almost looks like a faucet washer under the screw head.
Could it have been to clean grunge out of an old faucet?
369) It looks as though it is for stretching chain links or perhaps
rings to crimp into farm animals for identification. It is
certainly not for crimping them, however.
Now to see what others have said.
Enjoy,
DoN.
--
Email: <[email protected]> | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---
In article <[email protected]>,
Mark and Kim Smith <[email protected]> wrote:
>R.H. wrote:
>
>>Another set has just been posted:
>>
>>http://puzzlephotos.blogspot.com/
>>
>>
>>Rob
>>
>>
>>
>>
> From Rec.woodworking
>
>#363: Mirror? The prisms will bend light around a corner. So it would
>act like a mirror?
Even better -- the two in cooperation can produce an image
without the usual left-for-right reversal. Thus, you can see yourself
as others see you. (But you would need larger ones for that.)
Enjoy,
DoN.
--
Email: <[email protected]> | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---
In article <[email protected]>,
Andy Dingley <[email protected]> wrote:
>On 3 Jun 2005 00:40:50 -0400, [email protected] (DoN. Nichols) wrote:
>
>>>#363: Mirror? The prisms will bend light around a corner. So it would
>>>act like a mirror?
>>
>> Even better -- the two in cooperation can produce an image
>>without the usual left-for-right reversal. Thus, you can see yourself
>>as others see you. (But you would need larger ones for that.)
>
>Here's a bathroom cabinet I made recently.
>http://codesmiths.com/shed/furniture/cabinets/swarf/
>
>Note the mirrors.
Nice. You even have a partial image of you in the "jet mirror",
showing the expected reversal (as indicated by the finger pushing the
shutter release).
The "jet mirror" -- is that mounted in a ring into which turbine
blades dovetail? Ir is it a ring gear of some sort?
Enjoy,
DoN.
--
Email: <[email protected]> | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---
In article <[email protected]>,
R.H. <[email protected]> wrote:
>All but the first have been answered correctly, I'll go ahead and give the
>answer to that one also, I usually don't get very many guesses after the
>first day.
[ ... ]
>363. The prisms can be used to make an optical device called a pseudoscope.
>I made a separate page with more info on this one:
>
>http://pseudoscope.blogspot.com/
Nice! And nice to see another facet of Wheatstone's interests.
(He was the inventor of the English system concertina (which is one of
my special interests), among other things.)
Enjoy,
DoN.
--
Email: <[email protected]> | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---
In article <[email protected]>,
Andy Dingley <[email protected]> wrote:
>On 3 Jun 2005 17:53:41 -0400, [email protected] (DoN. Nichols) wrote:
>
>> The "jet mirror" -- is that mounted in a ring into which turbine
>>blades dovetail? Ir is it a ring gear of some sort?
>
>That's one of the little ones. I've made several.
>
>That particular one is just a knife-edge seal - the diagonal bars round
>the edge hold it in place and there are a couple of sharp rings on the
>inside edge to form the seal. Some of the others are "stator" rings -
>static vanes at the end of the compresor stage.
Thanks.
I presume that these were pulled from over-time engines?
Enjoy,
DoN.
--
Email: <[email protected]> | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---
* [email protected]
> 363 Periscope
I also thought so, but "amazing" and "not familiar with" didn't sound
right.
> 367 Chronographic Device? - Stopwatch?
Rythm counter? Speed measurment device?
--
Jon Haugsand
Dept. of Informatics, Univ. of Oslo, Norway, mailto:[email protected]
http://www.ifi.uio.no/~jonhaug/, Phone: +47 22 85 24 92
On Thu, 02 Jun 2005 07:37:04 GMT, "R.H."
<[email protected]> wrote in rec.woodworking:
>Another set has just been posted:
>
>http://puzzlephotos.blogspot.com/
363. Star Wars weapons guidance system, circa 1952?
364. Tire Pressure Gauge, circa 1932
366. Corkscrew, or chromium phallus from planet Zeptor
367. Pulse monitor, circa 1982
368. Catch-wheel/movement for a very primitive watch
(possibly from planet Zeptor)
369. A numerical progression of simple multiples of '3'.
Alt: a barbers' child detention device, circa 1942
--
+ TomH + antonomasia-at-canada-dot-com
A: Because it messes up the order in which people normally read text.
Q: Why is top-posting such a bad thing?
A: Top-posting.
Q: What is the most annoying thing on usenet and in e-mail?
Also: http://www.blakjak.demon.co.uk/gey_chr0.htm
"Julie" <[email protected]> wrote in message
news:[email protected]...
> R.H. wrote:
>> Another set has just been posted:
>>
>> http://puzzlephotos.blogspot.com/
>>
>
> 363. Hall of mirrors for mice
> 364. Washington Monument, for mice
> 365. Capatult for mice
> 366. Corkscrew
> 367. Electronic metronome
> 368. Merry-go-round for mice
> 369. Capult for mice
Actually Julie, #369 is a Mouse Juicer (for making delicious
freshly-squeezed-mice drinks!)
;)
- Michael
DoN. Nichols wrote:
> 365) A "capo" -- for holding the strings to a fret on a stringed
> instrument like a guitar or a banjo, to allow changing keys
> without having to retune everything -- or without having to
> learn alternate fingerings to play in another key. I think that
> this one must be for a banjo, as it does not appear to be wide
> enough to get all of the strings on a guitar.
It's not for a banjo.
--julie
"Julie" <[email protected]> wrote in message
news:[email protected]...
> R.H. wrote:
> > 365. 3-String capo
>
> Minor clarification from the web site-- this isn't so much for "tuning"
> the guitar as it is for reorienting the string configuration...
Thanks for the follow-up.
On Fri, 03 Jun 2005 19:03:36 +0000, R.H. wrote:
>
> 368. Saw blade
I'm terribly disappointed here. The original says:
368. 1-1/2" long, thanks to Elijah for this photo, it's a tool he made for
a very specific purpose. What is it and what was it made for?
Well, yeah, OK, saw blade, albeit a pretty cruddy one, but _what
was it made FOR?_ i.e. what was that specific purpose?
Don't tease. ;-)
Thanks,
Rich
[crossposted to:
rec.antiques,rec.crafts.metalworking,rec.puzzles,rec.woodworking,sci.electronics.design
I've set followups-to to rec.puzzles,sci.electronics.design - please
manage crossposted followups-to intelligently. :-) ]
On Fri, 03 Jun 2005 21:10:27 +0000, R.H. wrote:
>> http://puzzlephotos.blogspot.com/
Rich Grise wrote:
Re: Item #368
> _what
>> was it made FOR?_ i.e. what was that specific purpose?
>
> I was going to leave this as a "cliffhanger" until next week, but if you
> really want to know I guess I can spill it now. Here is the description
> that Elijah provided to me:
>
> "This is a saw for a depth controlled cut of plastic, specifically for
> cutting open a "wall wart" without damaging the transformer inside. I
> needed to resolder the output wires after they broke at the edge of the
> box. I put this in the chuck of a drill press, turned it on, then moved
> the transformer box around to cut it open along the existing seam."
Thanks! I'm sharing this with sci.electronics.design, because there
are always people who want to hack their wall warts! :-)
Cheers!
Rich
On 3 Jun 2005 00:40:50 -0400, [email protected] (DoN. Nichols) wrote:
>>#363: Mirror? The prisms will bend light around a corner. So it would
>>act like a mirror?
>
> Even better -- the two in cooperation can produce an image
>without the usual left-for-right reversal. Thus, you can see yourself
>as others see you. (But you would need larger ones for that.)
Here's a bathroom cabinet I made recently.
http://codesmiths.com/shed/furniture/cabinets/swarf/
Note the mirrors.
"R.H." <[email protected]> wrote in message
news:[email protected]...
> Another set has just been posted:
>
> http://puzzlephotos.blogspot.com/
>
>
> Rob
>
>
363 - Periscope
358 - Ice cube tray
365 - Jar opener
366 - Cork screw
367 - Pulse monitor
368 - Ratchet wheel
> 369 ?? Is it supposed to be used by pulling up on the handle or pushing
> down? Mounted on a board, looks like push down. Some kind of cobbler's
tool?
> Reminds me of a tool used for spreading battery cable terminals, but that
> wouldn't be mounted like that.
Yes, the handle is meant to push down, though the jaws don't close very much
when it is depressed, I posted a photo of it in this position on the answer
page.
Rob