why

vinel10 wrote:

> I have tried to get some information off this group and my messages is not
>even posted can some one tell me WHY
>
>

Apparently, you can post but not see your own posts.
Is it this one?

I have a 10inch craftsmans table saw model 113.298.240 serial and
date code 4229.po.788 the problem the blade is misaligned
from the cutoff groves its only about 1/32 but it hangs up on the back cut
any help as to how to adjust it thanks


>
>
>
>-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
>http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
>-----== Over 100,000 Newsgroups - 19 Different Servers! =-----
>
>

The Cabal strikes again?

charlie b

jo4hn wrote:
> labac on si ereht

And I thought it was because he was using TEST as a subject in a
non-test NG.

Dave in Fairfax
--
Dave Leader
reply-to doesn't work
use:
daveldr at att dot net
American Association of Woodturners
http://www.woodturner.org
Capital Area Woodturners
http://www.capwoodturners.org/

On 30 Aug 2004 13:31:43 GMT, John Doe <[email protected]> wrote:
> charlie b <[email protected]> wrote in
> news:[email protected]:
>
>> The Cabal strikes again?
>>
>
> There Is No Cabal
>

The absense of evidence for The Cabal is PROOF of the existance of The
Cabel.

Now where'd a put my tin-foil hat.

On Sun, 29 Aug 2004 20:01:47 -0400, Bill Schnakenberg <[email protected]>
wrote:

>vinel10 wrote:
>
>> I have tried to get some information off this group and my messages is not
>>even posted can some one tell me WHY
>>
>>
>
>Apparently, you can post but not see your own posts.
>Is it this one?
>
>I have a 10inch craftsmans table saw model 113.298.240 serial and
>date code 4229.po.788 the problem the blade is misaligned
>from the cutoff groves its only about 1/32 but it hangs up on the back cut
>any help as to how to adjust it thanks
>
>
>>
>>
>>
>>-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
>>http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
>>-----== Over 100,000 Newsgroups - 19 Different Servers! =-----
>>
>>

Bill,

That is the one he's concerned about. And it does look like he's unable to read
his own posts and possibly any replies to those posts. I'm in contact with him
via email. I suspect there is some setting/filter/etc. on his newsreader that is
interfering with his getting the headers/messages.

Tom Veatch
Wichita, KS USA

In article <[email protected]>,
vinel10 <[email protected]> wrote:
> I have tried to get some information off this group and my messages is not
>even posted can some one tell me WHY
>

You posted usiing plastic bits -- wooden ones are required in this group.

On Sun, 29 Aug 2004 18:50:13 -0400, "vinel10" <[email protected]> wrote:

> I have tried to get some information off this group and my messages is not
>even posted can some one tell me WHY
>
>
>
>
>-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
>http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
>-----== Over 100,000 Newsgroups - 19 Different Servers! =-----

Cannot give you any reason why the messages aren't being posted. This particular
message made it.

Rec.woodworking is NOT a moderated newsgroup so the messages do not go through
any kind of screening prior to posting. I would look to your ISP for answers.
Also, depending on the ISP, there may be some delay before the message appears.
So, be sure and give the system sufficient time before you assume that it has
been diverted or otherwise lost in the great bit bucket. How much time is
enough? Beats me.

But, please understand that there is no "overseer of the forum" who decides
whether a message is posted or has the ability to remove a message after it has
been posted.

Tom Veatch
Wichita, KS USA

charlie b <[email protected]> wrote in
news:[email protected]:

> The Cabal strikes again?
>

There Is No Cabal

Tom Veatch <[email protected]> wrote in
news:[email protected]:

> And it does look like he's
> unable to read his own posts and possibly any replies to those posts.
> I'm in contact with him via email. I suspect there is some
> setting/filter/etc. on his newsreader that is interfering with his
> getting the headers/messages.

If you can get him to use something other than Outlook Express, that
would probably help a lot. There is some weird combination of settings
in OE which automatically marks one's own posts as "read", and then
hides all read posts.

John

On Sun, 29 Aug 2004 18:50:13 -0400, "vinel10"
<[email protected]> wrote:

> I have tried to get some information off this group and my messages is not
>even posted can some one tell me WHY
>
>
>
In Outlook Express don't you need to hit "Send/Receive" to get it to
send a message?

Occasionally, when I post (using Agent) it will post immediately or
wait until I exit the application. I don't know why, but I guess I
would if I were the developer.

labac on si ereht
4j

Edwin Pawlowski wrote:

> "vinel10" <[email protected]> wrote in message
>
>>I have tried to get some information off this group and my messages is not
>>even posted can some one tell me WHY
>
>
> You have not been approved by the cabal
>
>

"vinel10" <[email protected]> wrote in message
> I have tried to get some information off this group and my messages is not
> even posted can some one tell me WHY

You have not been approved by the cabal

It's laying on top of the jacket with the LONG sleeves.

On Mon, 30 Aug 2004 14:30:26 GMT, "U-CDK_CHARLES\\Charles" <"Charles
Krug"@cdksystems.com> wrote:

>Now where'd a put my tin-foil hat.

On Sun, 29 Aug 2004 18:50:13 -0400, "vinel10"
<[email protected]> vaguely proposed a theory
......and in reply I say!:

remove ns from my header address to reply via email

Well, I found one of yours, with a reply, on Craftsman Table Saws.

> I have tried to get some information off this group and my messages is not
>even posted can some one tell me WHY
>
>
>
>
>-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
>http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
>-----== Over 100,000 Newsgroups - 19 Different Servers! =-----

*****************************************************
I have decided that I should not be offended by
anybody's behaviour but my own......the theory's
good, anyway.