A few months ago I added a 12" disk sander to my collection of sanders and
while I thought it would be one of those luxury sanders, I have found that
it has already seen more action than my OS Spindle sander that I have had
for 2 plus years.
I had an on site job in January that required lots of random length trim to
be added to a some kitchen cabinets. I took my miter saw and my 12" disk
sander. I cut the piece of trim close and tweaked with the sander. The
resulting miters came out perfect with no splintering or tear out.
Yesterday I visited the same customer to add 7" diameter columns between his
dining room and living room. More trim was used to match the shoe moldings
on the oak floors and again I used the 12" disk sander to make all the
miters. This time however I left the miter saw at home and took my
Milwaukee jig saw to get close on the lengths. With 80 grip paper on the
sander I was able to miter 1/2" x3/4" Oak shoe molding faster and with much
nicer results than using the miter saw. Sanding 45 degree bevels on the oak
moldings is quick and accurate.
Next time you have short pieces to miter you might consider the disk sander
for a safer and accurate alternative.
George wrote:
>
> "Leon" <[email protected]> wrote in message
> news:[email protected]...
<trim>
>> ...I cut the piece of trim close and tweaked with
>> the sander. The resulting miters came out perfect with no splintering
>> or tear out.
<trim>
>> With 80 grip paper on the sander I was able to miter 1/2" x3/4" Oak
>> shoe molding faster and with much nicer results than using the miter
>> saw. Sanding 45 degree bevels on the oak moldings is quick and accurate.
>> Next time you have short pieces to miter you might consider the disk
>> sander for a safer and accurate alternative.
>>
>>
> Already do, but owners of the lesser models with a simple rod and
> pressed trunnions are best advised to go to a human-powered shooting board.
I would have thought that doing the final adjustment on the miter saw
would have been more accurate and faster, assuming the blade was sharp
enough to not tear the wood, proper backer board, etc. I'm surprised you
were able to get those results with the 7" columns! I'll definitely have
to consider that next time.
--
Dekker
www.WoodworkDetails.com
"Leon" <[email protected]> wrote in message
news:[email protected]...
>A few months ago I added a 12" disk sander to my collection of sanders and
>while I thought it would be one of those luxury sanders, I have found that
>it has already seen more action than my OS Spindle sander that I have had
>for 2 plus years.
> I had an on site job in January that required lots of random length trim
> to be added to a some kitchen cabinets. I took my miter saw and my 12"
> disk sander. I cut the piece of trim close and tweaked with the sander.
> The resulting miters came out perfect with no splintering or tear out.
> Yesterday I visited the same customer to add 7" diameter columns between
> his dining room and living room. More trim was used to match the shoe
> moldings on the oak floors and again I used the 12" disk sander to make
> all the miters. This time however I left the miter saw at home and took
> my Milwaukee jig saw to get close on the lengths. With 80 grip paper on
> the sander I was able to miter 1/2" x3/4" Oak shoe molding faster and with
> much nicer results than using the miter saw. Sanding 45 degree bevels on
> the oak moldings is quick and accurate.
> Next time you have short pieces to miter you might consider the disk
> sander for a safer and accurate alternative.
>
>
Already do, but owners of the lesser models with a simple rod and pressed
trunnions are best advised to go to a human-powered shooting board.
Leon wrote:
> A few months ago I added a 12" disk sander to my collection of
sanders and
> while I thought it would be one of those luxury sanders, I have
found that
> it has already seen more action than my OS Spindle sander that I
have had
> for 2 plus years.
<snip>
You have just discovered what every boat builder knows.
A 12" disk sander is just about the most important tool you can have
for finish work on a boat.
BTW, Bingham shows how to build one with basically left overs.
Lew
Leon wrote:
> That is what I have been using it for however I actually bought it
with the
> idea of sanding smooh the box joint corners on small boxes. Hoping
to not
> round the corners over as is the case when using the finish sander
or ROS.
Doubt the grit would make much difference on a box joint, but if you
can justify the dedicated set up, I'd probably consider building a
dedicated disk sander using 100 grit along with a jig to clamp the box
and keep it square for the final finish sanding.
Even with a disk sander, you will either round over the corners or not
get a square finish, if you try to free hand.
Lew
"Dekker" <[email protected]> wrote in message
news:[email protected]...
>
>
>
> I would have thought that doing the final adjustment on the miter saw
> would have been more accurate and faster, assuming the blade was sharp
> enough to not tear the wood, proper backer board, etc. I'm surprised you
> were able to get those results with the 7" columns! I'll definitely have
> to consider that next time.
Understand that the shoe moldings went around The Square base and capitols
and this is a rather heavy bench top 12" disk sander.
That said however I have cut plenty of 2" long shoe moldings and with a
miter saw it gets dicey when working off the tail gate of the truck and not
all your hold downs and clamps are available. The cut pieces often fly in
all directions.
Also consider, you sand to the pencil or scribed line rather than work for
the blade to hit the mark. Kick back is very unlikely. You are not likely
to cut any body parts off.
Best of all, the NOISE level is reduced dramatically.
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
>
> You have just discovered what every boat builder knows.
>
> A 12" disk sander is just about the most important tool you can have for
> finish work on a boat.
>
> BTW, Bingham shows how to build one with basically left overs.
>
> Lew
OK, on a side note. Since you apparently have this style sander also, what
grit do you prefer? I think mine came with 80 and that piece still looks
new. I picked up a 120 thinking I would change it out but have not yet.
I was thinking also of cutting the center out of a 12" 120 and a 80 grit
disk so that you end up with a 8" diameter hole in the center of both disks.
Stick the 12", 80 grit ring on the disk and the 8", 120 grit circle in the
center of the 80 grit ring. The result hopefully would give you a fast
cutting outer ring and a smoother cutting inner circle.
Have you ever heard of that?
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
>
> You have just discovered what every boat builder knows.
>
> A 12" disk sander is just about the most important tool you can have for
> finish work on a boat.
>
> BTW, Bingham shows how to build one with basically left overs.
>
> Lew
Well I am certainly glad that I am well preceded with this discovery. ;~)
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
> Leon wrote:
> > OK, on a side note. Since you apparently have this style sander
> also, what
> > grit do you prefer?
>
> Think of this tool as an abrasive cutting, not a finishing device.
That is what I have been using it for however I actually bought it with the
idea of sanding smooh the box joint corners on small boxes. Hoping to not
round the corners over as is the case when using the finish sander or ROS.
Leon wrote:
> OK, on a side note. Since you apparently have this style sander
also, what
> grit do you prefer?
Think of this tool as an abrasive cutting, not a finishing device.
Haven't looked in a while, but think they are 50-60 grit disks.
Use PSA disks from Klingspor, which, BTW, is a total PITA unless you
use the tool at least weekly to keep the cement working.
Trying to mix two different grits on the same disk just seems like a
lot of work for little return.
No proof, just gut feel.
Lew