"Prometheus" <[email protected]> wrote in message
news:[email protected]...
> On Thu, 21 Apr 2005 17:26:15 -0400, "sidney"
> <don'tcallmei'[email protected]> wrote:
>
> >I made a Lynn jig for cutting box joints on the table saw. Can anyone
out
> >there give me a recommmendation for what saw blade to use in this
> >application? Seems like a rip blade, while flat ground, would cause too
> >much chip-out. What other blade would give me a flat-bottomed kerf?
>
> I've got a triple-chip Freud on my table saw, and it leaves a pretty
> flat bottom on the kerf. If you're not familiar with the triple chip
> style, it is similar to a rip blade, but every other tooth has the
> corners ground off and is ten thousandths higher than the rip teeth.
> The theory is that the triple chip tooth does the hogging out, and the
> rip tooth cleans up the kerf. I'm a big fan of them, personally.
>
> Aut inveniam viam aut faciam
I'm familiar with TCG blades. Specifically, which Freud blade are you
describing?
Sid
The Lynn's jig is the bomb man ! I made one too and really like being able
to use my 1/8" blade for any width and any height - in fact, I can do
variable spacing if I want to. Using the standard jig, any error is
cummulative, with the Lynn Jig, you can adjust it out on each finger. I
don't even do any test cuts anymore.
Don
"Stephen M" <[email protected]> wrote in message
news:[email protected]...
> Personally, I would use a dado set and have "fingers" the width of the
> dado
> setting.
>
> That said, chipout should not be a concern, as that han be handled with
> backer board.
>
> -Steve
> "sidney" <don'tcallmei'[email protected]> wrote in message
> news:[email protected]...
>> I made a Lynn jig for cutting box joints on the table saw. Can anyone
>> out
>> there give me a recommmendation for what saw blade to use in this
>> application? Seems like a rip blade, while flat ground, would cause too
>> much chip-out. What other blade would give me a flat-bottomed kerf?
>>
>> TIA
>>
>>
>
>
Don,
What blade do you use with your Lynn?
Sid
"D. J. Dorn" <[email protected]> wrote in message
news:[email protected]...
> The Lynn's jig is the bomb man ! I made one too and really like being
able
> to use my 1/8" blade for any width and any height - in fact, I can do
> variable spacing if I want to. Using the standard jig, any error is
> cummulative, with the Lynn Jig, you can adjust it out on each finger. I
> don't even do any test cuts anymore.
>
> Don
>
> "Stephen M" <[email protected]> wrote in message
> news:[email protected]...
> > Personally, I would use a dado set and have "fingers" the width of the
> > dado
> > setting.
> >
> > That said, chipout should not be a concern, as that han be handled with
> > backer board.
> >
> > -Steve
> > "sidney" <don'tcallmei'[email protected]> wrote in message
> > news:[email protected]...
> >> I made a Lynn jig for cutting box joints on the table saw. Can anyone
> >> out
> >> there give me a recommmendation for what saw blade to use in this
> >> application? Seems like a rip blade, while flat ground, would cause
too
> >> much chip-out. What other blade would give me a flat-bottomed kerf?
> >>
> >> TIA
> >>
> >>
> >
> >
>
>
>> I've got a triple-chip Freud on my table saw, and it leaves a pretty
>> flat bottom on the kerf. If you're not familiar with the triple chip
>> style, it is similar to a rip blade, but every other tooth has the
>> corners ground off and is ten thousandths higher than the rip teeth.
>> The theory is that the triple chip tooth does the hogging out, and the
>> rip tooth cleans up the kerf. I'm a big fan of them, personally.
>>
>> Aut inveniam viam aut faciam
>
>I'm familiar with TCG blades. Specifically, which Freud blade are you
>describing?
The one I've got is a 60 tooth Freud industrial "Heavy-Duty
all-purpose" blade with a 10 degree hook. It's got an eighth inch
kerf, and while it doesn't leave a perfectly flat bottom, it's pretty
close. I don't have a saw with a long enough arbor for a dado stack
yet, so I use this one, and make several passes. The two tiny ledges
on either side of the cut come out very easily with a hand file or a
sharp chisel. I cut about 40 dadoes with the thing today (set of
bedside tables in maple and butternut, for the curious), and it worked
like a charm- no chip-out at all.
Aut inveniam viam aut faciam
"Ba r r y" wrote in message
> On Fri, 22 Apr 2005 06:47:44 -0500, "Swingman" wrote:
>
> >
> >"Ba r r y" wrote in message
> >
> >> Not at all. You really do have the "Beautiful People".
> >
> >Fine, if you like replacing your steak with cotton candy ...
>
> Actually, "meat with eyes" comes to mind with some of those folks.
LOL ... and with choppers that blind.
--
www.e-woodshop.net
Last update: 4/17/05
"sidney" <don'tcallmei'[email protected]> wrote in
news:[email protected]:
> I made a Lynn jig for cutting box joints on the table saw. Can anyone
> out there give me a recommmendation for what saw blade to use in this
> application? Seems like a rip blade, while flat ground, would cause
> too much chip-out. What other blade would give me a flat-bottomed
> kerf?
>
> TIA
One that your local saw blade sharpener recommends and sharpens for that
purpose. Mine sold me one for about $60, including the
penalty^H^H^H^Hsales taxes we Californians pay for the privilege of living
in this shaky land.
YWIA
Patriarch
Ba r r y <[email protected]> wrote in
news:[email protected]:
> On Thu, 21 Apr 2005 18:07:15 -0500, Patriarch
> <[email protected]> wrote:
>
>> including the
>>penalty^H^H^H^Hsales taxes we Californians pay for the privilege of
>>living in this shaky land.
>
> Not to mention looking at the "beautiful people". <G>
>
> Barry
>
Are you making fun of the Governator?
Someday, we'll straighten things out. Otherwise, Oregon and Washington
will have a severe housing shortage. ;-)
Patriarch
"Swingman" <[email protected]> wrote in news:D6qdnY9c64fUefXfRVn-
[email protected]:
>
> "Ba r r y" wrote in message
>
>> Not at all. You really do have the "Beautiful People".
>
> Fine, if you like replacing your steak with cotton candy ...
>
There's a new series, on Discovery or TLC, called "Sheer Dallas", which
seems to indicate that the phenomenon is not entirely limited to SoCal.
The promos were sufficient for me to put it on the 'long list'.
Patriarch
On Fri, 22 Apr 2005 06:47:44 -0500, "Swingman" <[email protected]> wrote:
>
>"Ba r r y" wrote in message
>
>> Not at all. You really do have the "Beautiful People".
>
>Fine, if you like replacing your steak with cotton candy ...
Actually, "meat with eyes" comes to mind with some of those folks.
Barry
"D. J. Dorn" <[email protected]> wrote in message
news:[email protected]...
> The Lynn's jig is the bomb man ! I made one too and really like being
able
> to use my 1/8" blade for any width and any height - in fact, I can do
> variable spacing if I want to. Using the standard jig, any error is
> cummulative, with the Lynn Jig, you can adjust it out on each finger. I
> don't even do any test cuts anymore.
>
Do any of you guys have the plans for the Lynn's Box Jig? I've googled for
the plans and all of the results point to netexperts which appears to be
defunct. Could someone post them up to a web site somewhere or to the
binaries group for download?
Thanks,
--
-Mike-
[email protected]
Use a blade from your dado set.
-Dan
On Thu, 21 Apr 2005 17:26:15 -0400, "sidney"
<don'tcallmei'[email protected]> wrote:
>I made a Lynn jig for cutting box joints on the table saw. Can anyone out
>there give me a recommmendation for what saw blade to use in this
>application? Seems like a rip blade, while flat ground, would cause too
>much chip-out. What other blade would give me a flat-bottomed kerf?
>
>TIA
>
Personally, I would use a dado set and have "fingers" the width of the dado
setting.
That said, chipout should not be a concern, as that han be handled with
backer board.
-Steve
"sidney" <don'tcallmei'[email protected]> wrote in message
news:[email protected]...
> I made a Lynn jig for cutting box joints on the table saw. Can anyone out
> there give me a recommmendation for what saw blade to use in this
> application? Seems like a rip blade, while flat ground, would cause too
> much chip-out. What other blade would give me a flat-bottomed kerf?
>
> TIA
>
>
On Fri, 22 Apr 2005 20:27:18 -0500, "D. J. Dorn" <[email protected]>
wrote:
>The Lynn's jig is the bomb man ! I made one too and really like being able
>to use my 1/8" blade for any width and any height - in fact, I can do
>variable spacing if I want to. Using the standard jig, any error is
>cummulative, with the Lynn Jig, you can adjust it out on each finger. I
>don't even do any test cuts anymore.
Do you have a working link to the jig plans? Everything Google turns
up is not found.
Thanks!
..Joe L
On Thu, 21 Apr 2005 17:26:15 -0400, "sidney"
<don'tcallmei'[email protected]> wrote:
>I made a Lynn jig for cutting box joints on the table saw. Can anyone out
>there give me a recommmendation for what saw blade to use in this
>application? Seems like a rip blade, while flat ground, would cause too
>much chip-out. What other blade would give me a flat-bottomed kerf?
I've got a triple-chip Freud on my table saw, and it leaves a pretty
flat bottom on the kerf. If you're not familiar with the triple chip
style, it is similar to a rip blade, but every other tooth has the
corners ground off and is ten thousandths higher than the rip teeth.
The theory is that the triple chip tooth does the hogging out, and the
rip tooth cleans up the kerf. I'm a big fan of them, personally.
Aut inveniam viam aut faciam
On Thu, 21 Apr 2005 18:07:15 -0500, Patriarch
<[email protected]> wrote:
> including the
>penalty^H^H^H^Hsales taxes we Californians pay for the privilege of living
>in this shaky land.
Not to mention looking at the "beautiful people". <G>
Barry
On Fri, 22 Apr 2005 01:27:29 -0500, Patriarch
<[email protected]> wrote:
>Are you making fun of the Governator?
Not at all. You really do have the "Beautiful People". You don't
think they could have filmed "Baywatch" here in Connecticut, do you?
I work with women who think Donald Trump is good looking without his
wallet. <G>
Barry
On Sat, 23 Apr 2005 15:44:58 GMT, Joe <[email protected]>
wrote:
>Do you have a working link to the jig plans? Everything Google turns
>up is not found.
Found it - Yahoo search turned up http://www.leestyron.com/lynnjig.php
..Joe L