To the best of my knowledge, bandsaws cut with a downward motion and the
points of the blade should point that way too. I have a blade that looks
like the points are upside down with a relatively flat (very small angle) at
the top of each tooth and a sharp angle from the bottom to the point. Is
this ever correct or do I have a blade that was manufactured wrong?
TIA
Norm
On Jan 27, 10:29=A0am, "Norm Dresner" <[email protected]> wrote:
> To the best of my knowledge, bandsaws cut with a downward motion and the
> points of the blade should point that way too. =A0I have a blade that loo=
ks
> like the points are upside down with a relatively flat (very small angle)=
at
> the top of each tooth and a sharp angle from the bottom to the point. =A0=
Is
> this ever correct or do I have a blade that was manufactured wrong?
> =A0 =A0 TIA
> =A0 =A0 =A0 =A0 Norm
Trick for upside down and backwards (not as radical as the radial arm
saw guy) bandsaw blades or just backwards.
To get the look of rough cut cedar mill your lumber as you wood for
any project and dry fit all of the parts. Guide the faces of the cedar
that you want to look rough cut at an angle past the upside down and
backwards bandsaw blade.
I guess you could liken it to a big rasp that you use whatever
pressure you need against it to get the desired look.
Robb
On Tue, 27 Jan 2009 11:18:56 -0600, Larry Blanchard <[email protected]> wrote:
>On Tue, 27 Jan 2009 16:19:22 +0000, Norm Dresner wrote:
>
>> Many thanks to the people who wrote in to tell me that the blade was
>> inside-out. Once I flipped it, it was perfect!
>
>I've been working part time at the local Woodcraft. Don't feel alone -
>you'd be surprised how many times we get that question :-).
And they don't cut very well if the teeth are pointing up.. DAMHIKT
Also, gloves ARE recommended for handling the blades, especially when uncoiling
them or turning them right-side-out..
mac
Please remove splinters before emailing
On Tue, 27 Jan 2009 10:32:33 -0800, mac davis wrote:
> And they don't cut very well if the teeth are pointing up.. DAMHIKT
Nicely polished kerf though.
> Also, gloves ARE recommended for handling the blades, especially when
> uncoiling them or turning them right-side-out..
You hold them while uncoiling? I thought throwing them on the lawn was
the approved technique?
It's in-side-out.
Turn the blade inside-out (from it's current state), then turn it around to
point the teeth forward.
(FWIW I had to try try it with a marked up rubber band to prove it to
myself)
-Steve
"Norm Dresner" <[email protected]> wrote in message
news:[email protected]...
> To the best of my knowledge, bandsaws cut with a downward motion and the
> points of the blade should point that way too. I have a blade that looks
> like the points are upside down with a relatively flat (very small angle)
> at
> the top of each tooth and a sharp angle from the bottom to the point. Is
> this ever correct or do I have a blade that was manufactured wrong?
> TIA
> Norm
>
> Many thanks to the people who wrote in to tell me that the blade was
> inside-out. Once I flipped it, it was perfect!
>
> Once again, proving the power of the web.
Man. Had I been a few hours earlier I could have answered this for you from
experience. The shop next door has a band saw and the guy comes over to us
two days ago and says, "Hey... This blade was manufactured backwards!"
It took us a few seconds to "fix" his blade and we didn't let him see how we
did it. He walked away 10 minutes later all confused at our magic trick. :)
Apparently, when they coil them up for shipment, it is either easy to flip
them or someone does it as a prank...
Glad you got yours fixed.
Regards,
Joe Agro, Jr.
(800) 871-5022
01.908.542.0244
Automatic / Pneumatic Drills: http://www.AutoDrill.com
Multiple Spindle Drills: http://www.Multi-Drill.com
Flagship Site: http://www.Drill-N-Tap.com
V8013-R
"Norm Dresner" <[email protected]> wrote in message
news:[email protected]...
| To the best of my knowledge, bandsaws cut with a downward motion and the
| points of the blade should point that way too. I have a blade that looks
| like the points are upside down with a relatively flat (very small angle)
at
| the top of each tooth and a sharp angle from the bottom to the point. Is
| this ever correct or do I have a blade that was manufactured wrong?
| TIA
| Norm
Many thanks to the people who wrote in to tell me that the blade was
inside-out. Once I flipped it, it was perfect!
Once again, proving the power of the web.
Norm
On Tue, 27 Jan 2009 16:19:22 +0000, Norm Dresner wrote:
> Many thanks to the people who wrote in to tell me that the blade was
> inside-out. Once I flipped it, it was perfect!
I've been working part time at the local Woodcraft. Don't feel alone -
you'd be surprised how many times we get that question :-).
--
It's turtles, all the way down
On Jan 27, 1:15=A0pm, "basilisk" <[email protected]> wrote:
> "mac davis" <[email protected]> wrote in message
>
> news:[email protected]...
>
>
>
> > On Tue, 27 Jan 2009 11:18:56 -0600, Larry Blanchard <[email protected]=
m>
> > wrote:
>
> >>On Tue, 27 Jan 2009 16:19:22 +0000, Norm Dresner wrote:
>
> >>> Many thanks to the people who wrote in to tell me that the blade was
> >>> inside-out. =A0Once I flipped it, it was perfect!
>
> >>I've been working part time at the local Woodcraft. =A0Don't feel alone=
-
> >>you'd be surprised how many times we get that question :-).
>
> > And they don't cut very well if the teeth are pointing up.. DAMHIKT
>
> > Also, gloves ARE recommended for handling the blades, especially when
> > uncoiling
> > them or turning them right-side-out..
>
> One of the mills that I worked at years ago had a double band breakdown s=
aw,
> basically a sharp chain would carry a log through a right and left bandmi=
ll,
> cutting
> a slab from either side, leaving a two sided cant to pass through a gang
> saw.
>
> The bandsaws were sharpened in house and the sawfilers would occasionally
> have to turn one of these bands inside out to use on the other side of th=
e
> mill.
> These bands were 6 inches wide, 20 feet or so long and the filers made it
> look
> easy and as far as I know no one was ever hurt in the process.
> Scary stuff with that much spring steel moving all at once.
>
> basilisk- Hide quoted text -
>
> - Show quoted text -
You like big blades? Try this
http://www.garymkatz.com/OnTheRoad/hull_oaks.html
Nahmie
"mac davis" <[email protected]> wrote in message
news:[email protected]...
> On Tue, 27 Jan 2009 11:18:56 -0600, Larry Blanchard <[email protected]>
> wrote:
>
>>On Tue, 27 Jan 2009 16:19:22 +0000, Norm Dresner wrote:
>>
>>> Many thanks to the people who wrote in to tell me that the blade was
>>> inside-out. Once I flipped it, it was perfect!
>>
>>I've been working part time at the local Woodcraft. Don't feel alone -
>>you'd be surprised how many times we get that question :-).
>
> And they don't cut very well if the teeth are pointing up.. DAMHIKT
>
> Also, gloves ARE recommended for handling the blades, especially when
> uncoiling
> them or turning them right-side-out..
>
One of the mills that I worked at years ago had a double band breakdown saw,
basically a sharp chain would carry a log through a right and left bandmill,
cutting
a slab from either side, leaving a two sided cant to pass through a gang
saw.
The bandsaws were sharpened in house and the sawfilers would occasionally
have to turn one of these bands inside out to use on the other side of the
mill.
These bands were 6 inches wide, 20 feet or so long and the filers made it
look
easy and as far as I know no one was ever hurt in the process.
Scary stuff with that much spring steel moving all at once.
basilisk
Norm Dresner wrote:
> To the best of my knowledge, bandsaws cut with a downward motion and the
> points of the blade should point that way too. I have a blade that looks
> like the points are upside down with a relatively flat (very small angle) at
> the top of each tooth and a sharp angle from the bottom to the point. Is
> this ever correct or do I have a blade that was manufactured wrong?
> TIA
> Norm
>
Sounds like it is turned inside out.
--
Gerald Ross
Cochran, GA
Murphy was an optimist.
"PCPaul" <[email protected]> wrote in message
news:[email protected]...
> On Tue, 27 Jan 2009 10:32:33 -0800, mac davis wrote:
>
>> And they don't cut very well if the teeth are pointing up.. DAMHIKT
>
> Nicely polished kerf though.
>
>> Also, gloves ARE recommended for handling the blades, especially when
>> uncoiling them or turning them right-side-out..
>
> You hold them while uncoiling? I thought throwing them on the lawn was
> the approved technique?
>
Strange enough the shorter blades can eat you if you are not careful, and
tossing them in the yard is a safe method. Longer blades, mine is 150"
long, are very easily opened and closed while holding them with 2 hands.