I'm building some desk drawers out of plywood. To hide the edges of the
plywood, I banded them with a thin piece of pine. The trouble is, I got
ahead of myself and would like to remove the banding.
I could cut the banding off with the table saw without a problem, but In
true Norm fashion I shot a couple of nails in until the glue dried. Any
suggestions on how to remove the banding without messing up the plywood?
The glue was Titebond II.
Puckdropper
On 2011-10-17 04:37:23 +0000, Richard said:
> On 10/16/2011 8:09 AM, Leon wrote:
>> On 10/15/2011 7:32 PM, Larry Jaques wrote:
>>> On 15 Oct 2011 23:51:04 GMT, Puckdropper
>>> <puckdropper(at)yahoo(dot)com> wrote:
>>>
>>>> I'm building some desk drawers out of plywood. To hide the edges of the
>>>> plywood, I banded them with a thin piece of pine. The trouble is, I got
>>>> ahead of myself and would like to remove the banding.
>>>
>>> A hot iron would take the banding right off, Pucky. It wouldn't,
>>> however, clean up the edge. What does "ahead of myself" mean here?
>>
>> He used nails to reinforce the banding, are you suggesting he burn the
>> banding off with the iron? I suspect the banding would burn before the
>> adhesive warmed up. ;~)
>
>
> I'd thing the adhesive would release first - just using a hot iron.
>
> I'd also not expect to reuse it...
That depends on the banding material and the adhesive. If it is the
iron on veneer type, then this might work. But if it is solid wood, it
woudl be mroe difficult.
"Mike Marlow" <[email protected]> wrote in news:6cfa3$4e9a26c0
[email protected]:
> Puckdropper wrote:
>> I'm building some desk drawers out of plywood. To hide the edges of
>> the plywood, I banded them with a thin piece of pine. The trouble
>> is, I got ahead of myself and would like to remove the banding.
>>
>> I could cut the banding off with the table saw without a problem, but
>> In true Norm fashion I shot a couple of nails in until the glue
>> dried. Any suggestions on how to remove the banding without messing
>> up the plywood?
>>
>> The glue was Titebond II.
>>
>
> Read the Titebond web site. Heat will loosen it. If they are just
> finishing nails and you didn't go crazy with them - just cut them off.
>
I did not know about the heat. Maybe I can get the glue to loosen and
get a good grip on the nails once the pieces have separated.
Puckdropper
Larry Jaques <[email protected]> wrote in
news:[email protected]:
> On 15 Oct 2011 23:51:04 GMT, Puckdropper
> <puckdropper(at)yahoo(dot)com> wrote:
>
>>I'm building some desk drawers out of plywood. To hide the edges of
>>the plywood, I banded them with a thin piece of pine. The trouble is,
>>I got ahead of myself and would like to remove the banding.
>
> A hot iron would take the banding right off, Pucky. It wouldn't,
> however, clean up the edge. What does "ahead of myself" mean here?
>
Once the nails are gone or at least below the surface, sand paper would
clean up the edges nicely.
What "ahead of myself" means is I cut some wood strips and glued them on
the plywood before I had all the strips cut. I changed my mind on how to
build things so I've got 3 drawer fronts with banding I don't want and 3
without.
Puckdropper
Puckdropper <puckdropper(at)yahoo(dot)com> wrote in
news:[email protected]:
> I'm building some desk drawers out of plywood. To hide the edges of
> the plywood, I banded them with a thin piece of pine. The trouble is,
> I got ahead of myself and would like to remove the banding.
>
> I could cut the banding off with the table saw without a problem, but
> In true Norm fashion I shot a couple of nails in until the glue dried.
> Any suggestions on how to remove the banding without messing up the
> plywood?
>
> The glue was Titebond II.
>
> Puckdropper
I wound up using a combination of methods... I started with a chisel
and pried the banding off until it broke (usually around the first
nail.) Once enough of the nail was exposed I tried to pull the nail (1
1/4" brad nail). Some pulled, others I had to bury in the plywood.
Some sanding to remove the bits that were glued tight and I've got a set
of drawers that match.
Puckdropper
Puckdropper wrote:
> "Mike Marlow" <[email protected]> wrote in
> news:6cfa3$4e9a26c0 [email protected]:
>
>> Puckdropper wrote:
>>> I'm building some desk drawers out of plywood. To hide the edges of
>>> the plywood, I banded them with a thin piece of pine. The trouble
>>> is, I got ahead of myself and would like to remove the banding.
>>>
>>> I could cut the banding off with the table saw without a problem,
>>> but In true Norm fashion I shot a couple of nails in until the glue
>>> dried. Any suggestions on how to remove the banding without messing
>>> up the plywood?
>>>
>>> The glue was Titebond II.
>>>
>>
>> Read the Titebond web site. Heat will loosen it. If they are just
>> finishing nails and you didn't go crazy with them - just cut them
>> off.
>>
>
> I did not know about the heat. Maybe I can get the glue to loosen and
> get a good grip on the nails once the pieces have separated.
>
I felt so informed when I wrote that! Turns out that just a week and a half
ago I was in a similar situation and had to look it up myself...
--
-Mike-
[email protected]
Puckdropper wrote:
> I'm building some desk drawers out of plywood. To hide the edges of
> the plywood, I banded them with a thin piece of pine. The trouble
> is, I got ahead of myself and would like to remove the banding.
>
> I could cut the banding off with the table saw without a problem, but
> In true Norm fashion I shot a couple of nails in until the glue
> dried. Any suggestions on how to remove the banding without messing
> up the plywood?
>
> The glue was Titebond II.
>
Read the Titebond web site. Heat will loosen it. If they are just
finishing nails and you didn't go crazy with them - just cut them off.
--
-Mike-
[email protected]
On 15 Oct 2011 23:51:04 GMT, Puckdropper
<puckdropper(at)yahoo(dot)com> wrote:
>I'm building some desk drawers out of plywood. To hide the edges of the
>plywood, I banded them with a thin piece of pine. The trouble is, I got
>ahead of myself and would like to remove the banding.
A hot iron would take the banding right off, Pucky. It wouldn't,
however, clean up the edge. What does "ahead of myself" mean here?
--
Happiness lies in the joy of achievement and the thrill of creative effort.
-- Franklin D. Roosevelt
On 10/15/2011 7:32 PM, Larry Jaques wrote:
> On 15 Oct 2011 23:51:04 GMT, Puckdropper
> <puckdropper(at)yahoo(dot)com> wrote:
>
>> I'm building some desk drawers out of plywood. To hide the edges of the
>> plywood, I banded them with a thin piece of pine. The trouble is, I got
>> ahead of myself and would like to remove the banding.
>
> A hot iron would take the banding right off, Pucky. It wouldn't,
> however, clean up the edge. What does "ahead of myself" mean here?
>
> --
> Happiness lies in the joy of achievement and the thrill of creative effort.
> -- Franklin D. Roosevelt
He used nails to reinforce the banding, are you suggesting he burn the
banding off with the iron? I suspect the banding would burn before the
adhesive warmed up. ;~)
"Puckdropper" <puckdropper(at)yahoo(dot)com> wrote in message
news:[email protected]...
> I'm building some desk drawers out of plywood. To hide the edges of the
> plywood, I banded them with a thin piece of pine. The trouble is, I got
> ahead of myself and would like to remove the banding.
>
> I could cut the banding off with the table saw without a problem, but In
> true Norm fashion I shot a couple of nails in until the glue dried. Any
> suggestions on how to remove the banding without messing up the plywood?
>
> The glue was Titebond II.
>
> Puckdropper
To get the nails out, if you have a plug cutter cut around the nail. Pry the
round piece of the band away and pull the nails out. Then table saw the band
off. WW
On 10/15/2011 6:51 PM, Puckdropper wrote:
> I'm building some desk drawers out of plywood. To hide the edges of the
> plywood, I banded them with a thin piece of pine. The trouble is, I got
> ahead of myself and would like to remove the banding.
>
> I could cut the banding off with the table saw without a problem, but In
> true Norm fashion I shot a couple of nails in until the glue dried. Any
> suggestions on how to remove the banding without messing up the plywood?
...
Assuming you didn't put a zillion in and they're not 16d spikes, take an
old blade and just go ahead and cut.
Or, assuming the banding isn't important (you can make more), dig out
enough of a hole around them and pull 'em.
--
On 10/16/2011 8:09 AM, Leon wrote:
> On 10/15/2011 7:32 PM, Larry Jaques wrote:
>> On 15 Oct 2011 23:51:04 GMT, Puckdropper
>> <puckdropper(at)yahoo(dot)com> wrote:
>>
>>> I'm building some desk drawers out of plywood. To hide the edges of the
>>> plywood, I banded them with a thin piece of pine. The trouble is, I got
>>> ahead of myself and would like to remove the banding.
>>
>> A hot iron would take the banding right off, Pucky. It wouldn't,
>> however, clean up the edge. What does "ahead of myself" mean here?
>>
>> --
>> Happiness lies in the joy of achievement and the thrill of creative
>> effort.
>> -- Franklin D. Roosevelt
>
> He used nails to reinforce the banding, are you suggesting he burn the
> banding off with the iron? I suspect the banding would burn before the
> adhesive warmed up. ;~)
I'd thing the adhesive would release first - just using a hot iron.
I'd also not expect to reuse it...
On 10/16/2011 11:37 PM, Richard wrote:
> On 10/16/2011 8:09 AM, Leon wrote:
>> On 10/15/2011 7:32 PM, Larry Jaques wrote:
>>> On 15 Oct 2011 23:51:04 GMT, Puckdropper
>>> <puckdropper(at)yahoo(dot)com> wrote:
>>>
>>>> I'm building some desk drawers out of plywood. To hide the edges of the
>>>> plywood, I banded them with a thin piece of pine. The trouble is, I got
>>>> ahead of myself and would like to remove the banding.
>>>
>>> A hot iron would take the banding right off, Pucky. It wouldn't,
>>> however, clean up the edge. What does "ahead of myself" mean here?
>>>
>>> --
>>> Happiness lies in the joy of achievement and the thrill of creative
>>> effort.
>>> -- Franklin D. Roosevelt
>>
>> He used nails to reinforce the banding, are you suggesting he burn the
>> banding off with the iron? I suspect the banding would burn before the
>> adhesive warmed up. ;~)
>
>
> I'd thing the adhesive would release first - just using a hot iron.
>
> I'd also not expect to reuse it...
That may all depend on the thickness of the thin banding. LOL
I have scorched 1/16"veneer edge banding with an iron but when He
mentioned using nails to hold it in place I immediately ruled out
veneer. The thinnest banding I have used with nails was 1/4" thick. My
finish nailer sinks the heads 1/8" deep, My brad nailer does not sink
the heads so I would not use it at all. I still believe that might take
an exceptionally long time to remove with an iron.