I was by Lowes to pick up some lag bolts, for a set of wheels to move my
wood lathe. Thanks I think Leon for the video showing a perfect method..
pics later.
I saw the conversation on screws getting smaller.
Well the lags are shrinking both in length and width too.
Length has shrunk from previous screws by enough to raise my eyebrow. A
1 1/2 in screw previously measured 1 5/8 length (much older stock that I
had), now measures 1 3/8 in length.
The lag has also changed from 5/16 previously to 1/64 under.
Can't wait too see where we are going from here.
--
Jeff
On 2/12/2015 8:12 AM, Leon wrote:
> On 2/12/2015 6:40 AM, Swingman wrote:
>> A structural screw like Spax or GRK,
>> Expensive, but well worth it in strength and labor savings.
>>
>
>
> These are what I buy if strength matters, and yeah you can get them at
> the borg. ;~)
>
> http://www.homedepot.com/p/SPAX-1-4-in-x-6-in-External-Hex-Flange-Hex-Head-Lag-Screw-4571010701527/202041039
"Spax", by any other name...
;)
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
On 2/12/2015 10:48 AM, -MIKE- wrote:
> On 2/12/15 8:12 AM, Leon wrote:
>> On 2/12/2015 6:40 AM, Swingman wrote:
>>> On 2/11/2015 9:06 PM, -MIKE- wrote:
>>>
>>>> I'll never use another lag bolt again when there are structural
>>>> fasteners available that are stronger and made to much higher
>>>> standards.
>>>
>>> Yep. Been quite a few years since I've bought a lag bolt from a Borg.
>>>
>>> A structural screw like Spax or GRK, besides being hugely stronger in
>>> sheer force, has an added benefit in being easier to drive with a
>>> quality cordless drill.
>>>
>>> Expensive, but well worth it in strength and labor savings.
>>>
>>
>>
>> These are what I buy if strength matters, and yeah you can get them at
>> the borg. ;~)
>>
>> http://www.homedepot.com/p/SPAX-1-4-in-x-6-in-External-Hex-Flange-Hex-Head-Lag-Screw-4571010701527/202041039
>>
>>
>
> I love Spax.
> Next time you're there check out FastenMaster, if they're carried in
> your neck.
> I used this product on my "Sharn" and they were amazing...
> <http://www.fastenmaster.com/details/product/thrulok-screw-bolt-fastening-system.html>
>
>
>
Thanks. I think I have seen them on TOH recently.
woodchucker wrote:
>
>>I was by Lowes to pick up some lag bolts, for a set of wheels to
>>move my
>>wood lathe. Thanks I think Leon for the video showing a perfect
>>method..
>>pics later.
>>
>>I saw the conversation on screws getting smaller.
>>Well the lags are shrinking both in length and width too.
>>Length has shrunk from previous screws by enough to raise my
>>eyebrow. A
>>1 1/2 in screw previously measured 1 5/8 length (much older stock
>>that I
>>had), now measures 1 3/8 in length.
>>The lag has also changed from 5/16 previously to 1/64 under.
>>
>>Can't wait too see where we are going from here.
------------------------------------------------
Think metric standardization.
Lew
On 2/12/2015 7:40 AM, Swingman wrote:
> On 2/11/2015 9:06 PM, -MIKE- wrote:
>
>> I'll never use another lag bolt again when there are structural
>> fasteners available that are stronger and made to much higher standards.
>
> Yep. Been quite a few years since I've bought a lag bolt from a Borg.
>
> A structural screw like Spax or GRK, besides being hugely stronger in
> sheer force, has an added benefit in being easier to drive with a
> quality cordless drill.
>
> Expensive, but well worth it in strength and labor savings.
>
So SPAX doesn't fill the space on a wheel mounting plate like lags do.
I don't need heavy structural, I want to fill the space as much as possible.
I don't want the length, just noticed it was much smaller when compared
to an old lag.
And yep, spax are neat when used in the right application.
--
Jeff
On 2/11/2015 9:06 PM, -MIKE- wrote:
> I'll never use another lag bolt again when there are structural
> fasteners available that are stronger and made to much higher standards.
Yep. Been quite a few years since I've bought a lag bolt from a Borg.
A structural screw like Spax or GRK, besides being hugely stronger in
sheer force, has an added benefit in being easier to drive with a
quality cordless drill.
Expensive, but well worth it in strength and labor savings.
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
On 2/12/2015 6:40 AM, Swingman wrote:
> On 2/11/2015 9:06 PM, -MIKE- wrote:
>
>> I'll never use another lag bolt again when there are structural
>> fasteners available that are stronger and made to much higher standards.
>
> Yep. Been quite a few years since I've bought a lag bolt from a Borg.
>
> A structural screw like Spax or GRK, besides being hugely stronger in
> sheer force, has an added benefit in being easier to drive with a
> quality cordless drill.
>
> Expensive, but well worth it in strength and labor savings.
>
These are what I buy if strength matters, and yeah you can get them at
the borg. ;~)
http://www.homedepot.com/p/SPAX-1-4-in-x-6-in-External-Hex-Flange-Hex-Head-Lag-Screw-4571010701527/202041039
On Wed, 11 Feb 2015 21:37:29 -0800, "Lew Hodgett"
<[email protected]> wrote:
>
> woodchucker wrote:
>
>>
>>>I was by Lowes to pick up some lag bolts, for a set of wheels to
>>>move my
>>>wood lathe. Thanks I think Leon for the video showing a perfect
>>>method..
>>>pics later.
>>>
>>>I saw the conversation on screws getting smaller.
>>>Well the lags are shrinking both in length and width too.
>>>Length has shrunk from previous screws by enough to raise my
>>>eyebrow. A
>>>1 1/2 in screw previously measured 1 5/8 length (much older stock
>>>that I
>>>had), now measures 1 3/8 in length.
>>>The lag has also changed from 5/16 previously to 1/64 under.
>>>
>>>Can't wait too see where we are going from here.
>------------------------------------------------
>Think metric standardization.
>
>Lew
>
>
Nope, not in this case. 5/16 is as close to 8mm as damn is to
swearing. 7mm is not a "metric standard"
The length mabee - 35mm, vs 1 1/2 at 38mm and 1 5/8 at 41 (plus or
minus a few decimals)
>
On 2/11/15 9:00 PM, woodchucker wrote:
> I was by Lowes to pick up some lag bolts, for a set of wheels to move
> my wood lathe. Thanks I think Leon for the video showing a perfect
> method.. pics later.
>
> I saw the conversation on screws getting smaller. Well the lags are
> shrinking both in length and width too. Length has shrunk from
> previous screws by enough to raise my eyebrow. A 1 1/2 in screw
> previously measured 1 5/8 length (much older stock that I had), now
> measures 1 3/8 in length. The lag has also changed from 5/16
> previously to 1/64 under.
>
> Can't wait too see where we are going from here.
I'll never use another lag bolt again when there are structural
fasteners available that are stronger and made to much higher standards.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
[email protected] wrote:
> On Wed, 11 Feb 2015 22:00:43 -0500, woodchucker <[email protected]>
> wrote:
>
>> I was by Lowes to pick up some lag bolts, for a set of wheels to move my
>> wood lathe. Thanks I think Leon for the video showing a perfect method..
>> pics later.
>>
>> I saw the conversation on screws getting smaller.
>> Well the lags are shrinking both in length and width too.
>> Length has shrunk from previous screws by enough to raise my eyebrow. A
>> 1 1/2 in screw previously measured 1 5/8 length (much older stock that I
>> had), now measures 1 3/8 in length.
>> The lag has also changed from 5/16 previously to 1/64 under.
>>
>> Can't wait too see where we are going from here.
> "screwed" by the Chinese bolt manufacturers
"Crown" screws are made in Indianapolis. I stopped in once to try to
get something special. You want "How Many?" (LOL)
On 2/12/15 6:40 AM, Swingman wrote:
> On 2/11/2015 9:06 PM, -MIKE- wrote:
>
>> I'll never use another lag bolt again when there are structural
>> fasteners available that are stronger and made to much higher
>> standards.
>
> Yep. Been quite a few years since I've bought a lag bolt from a
> Borg.
>
> A structural screw like Spax or GRK, besides being hugely stronger in
> sheer force, has an added benefit in being easier to drive with a
> quality cordless drill.
>
> Expensive, but well worth it in strength and labor savings.
>
And they're not what I call "single drive." Meaning, you can back one
out and drive it back in without it breaking off like a lag bolt.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On 2/12/15 8:12 AM, Leon wrote:
> On 2/12/2015 6:40 AM, Swingman wrote:
>> On 2/11/2015 9:06 PM, -MIKE- wrote:
>>
>>> I'll never use another lag bolt again when there are structural
>>> fasteners available that are stronger and made to much higher standards.
>>
>> Yep. Been quite a few years since I've bought a lag bolt from a Borg.
>>
>> A structural screw like Spax or GRK, besides being hugely stronger in
>> sheer force, has an added benefit in being easier to drive with a
>> quality cordless drill.
>>
>> Expensive, but well worth it in strength and labor savings.
>>
>
>
> These are what I buy if strength matters, and yeah you can get them at
> the borg. ;~)
>
> http://www.homedepot.com/p/SPAX-1-4-in-x-6-in-External-Hex-Flange-Hex-Head-Lag-Screw-4571010701527/202041039
>
I love Spax.
Next time you're there check out FastenMaster, if they're carried in
your neck.
I used this product on my "Sharn" and they were amazing...
<http://www.fastenmaster.com/details/product/thrulok-screw-bolt-fastening-system.html>
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On Wed, 11 Feb 2015 22:00:43 -0500, woodchucker <[email protected]>
wrote:
>I was by Lowes to pick up some lag bolts, for a set of wheels to move my
>wood lathe. Thanks I think Leon for the video showing a perfect method..
>pics later.
>
>I saw the conversation on screws getting smaller.
>Well the lags are shrinking both in length and width too.
>Length has shrunk from previous screws by enough to raise my eyebrow. A
>1 1/2 in screw previously measured 1 5/8 length (much older stock that I
>had), now measures 1 3/8 in length.
>The lag has also changed from 5/16 previously to 1/64 under.
>
>Can't wait too see where we are going from here.
"screwed" by the Chinese bolt manufacturers