I am presently using a vertical raised panel bit to do some small jobs but
have taken on redoing my kitchen. Was looking at getting the new frued 2+2
raised panel cutter but would like to konw if you can make a cut in one pass
with this type of bit or do you have to adjust the fence two or three times
to take small cuts. I am using a Frued 3-1/4 HP variable speed router so I
should be OK in the Power department but would really like to know if the
extra money for the bigger bit is really worth the expence and will it save
any time.
Regards
Bill
Bill,
I've never used the bits to make mini-panel, but I have to think it
would be safer and less wear on the bit if you make multiple passes.
I have a stack of 1/4" boards that I spring clamp to the infeed and
outfeed side of my fence. After each pass, I simply remove one of the
boards from each side, thus cutting a 1/4" deeper into the panel. Its
very simple and very quick.
Would love to take credit for the idea, but its directly from one of
Pat Warner's books or a page on his website, I can't remember which.
Chuck
On Thu, 12 May 2005 13:25:38 GMT, "William Falconer"
<[email protected]> wrote:
>I am presently using a vertical raised panel bit to do some small jobs but
>have taken on redoing my kitchen. Was looking at getting the new frued 2+2
>raised panel cutter but would like to konw if you can make a cut in one pass
>with this type of bit or do you have to adjust the fence two or three times
>to take small cuts. I am using a Frued 3-1/4 HP variable speed router so I
>should be OK in the Power department but would really like to know if the
>extra money for the bigger bit is really worth the expence and will it save
>any time.
Contrary to the advice of others I've been making single-pass cuts in
red oak and ash for years with no problems. Jesada bits, instead of
Freud but no undue wear.
In denser woods, like maple, or woods prone to burn, like cherry,
multiple passes would probably be a good idea, and the 1/4" pieces
stacked against the fence, to be removed one by one, makes it about as
painless as its gonna get.
Testing with a piece of scrap will answer all your questions in very
short order.
Bill,
Woodchuck's reference to Pat Warner and his site www.patwarner.com is a good
place to learn. The idea of using the 1/4" boards in front of the fence
works great. Also consider that when routing across the grain you need to
take lighter cuts or you will get tearout. I have several sets of the Freud
raised panel bits and they have been excellent.
I made the router fence that Pat shows on his site and use a Rout-R-Lift so
height and depth of cut are micro-adjustable. I tend to take lighter cuts to
avoid tearout so I can't really tell you if you'll save time over using a
vertical bit. Depending on your fence, technique and several other factors,
I'd say the Freud bit is probably easier to use and perhaps even safer since
everything is on a nice flat surface and not being held vertically.
Bob S.
"William Falconer" <[email protected]> wrote in message
news:mPIge.106135$3V3.74301@edtnps89...
>I am presently using a vertical raised panel bit to do some small jobs but
> have taken on redoing my kitchen. Was looking at getting the new frued 2+2
> raised panel cutter but would like to konw if you can make a cut in one
> pass
> with this type of bit or do you have to adjust the fence two or three
> times
> to take small cuts. I am using a Frued 3-1/4 HP variable speed router so I
> should be OK in the Power department but would really like to know if the
> extra money for the bigger bit is really worth the expence and will it
> save
> any time.
>
>
> Regards
>
> Bill
>
>
Upscale,
Think I may have not been clear. I use the Freud horizontal (flat) type bits
for making my raised panels - not the vertical type bits. My only experience
with using a vertical panel bit was a disaster. I did not have a good fence
and wasn't able to keep the panel perpendicular to the table. That is what
prompted me to build a better fence (i.e. Pat Warner's design). Although I
haven't made a taller fence, it can be made to any (reasonable) height and
fastened to the rest of the fence - it's designed to be replaceable. After
building the fence - there was a big sale on Freud bits and that's when I
got the raised panel set and never bothered with a vertical bit again.
Sorry if my post misled you to thinking I might have known what I was
doing.........;-)
Bob S.
"Upscale" <[email protected]> wrote in message
news:[email protected]...
> "BobS" <[email protected]> wrote in message news:1hNge.27164
>> Upscale,
>> You posted your questions to the OP under my post - he may not see them.
>
> Yes I know, but you did say you were using vertical panel bits. Most if
> not
> all of the questions would apply to you as well as anyone else that uses
> vertical panel bits.
>
>
>
"BobS" <[email protected]> wrote in message news:1hNge.27164
> Upscale,
> You posted your questions to the OP under my post - he may not see them.
Yes I know, but you did say you were using vertical panel bits. Most if not
all of the questions would apply to you as well as anyone else that uses
vertical panel bits.
Build your table base up with several pieces of 1/4" ply.
Make a pass and remove a sheet. You can make the cut in
one pass but that's hard on the cutters and the router.
The Freud 2+2 is excellent.
William Falconer wrote:
> I am presently using a vertical raised panel bit to do some small jobs but
> have taken on redoing my kitchen. Was looking at getting the new frued 2+2
> raised panel cutter but would like to konw if you can make a cut in one pass
> with this type of bit or do you have to adjust the fence two or three times
> to take small cuts. I am using a Frued 3-1/4 HP variable speed router so I
> should be OK in the Power department but would really like to know if the
> extra money for the bigger bit is really worth the expence and will it save
> any time.
>
>
> Regards
>
> Bill
>
>
"BobS" <[email protected]> wrote in message news:EaJge.15589
> height and depth of cut are micro-adjustable. I tend to take lighter cuts
to
> avoid tearout so I can't really tell you if you'll save time over using a
> vertical bit. Depending on your fence, technique and several other
factors,
> I'd say the Freud bit is probably easier to use and perhaps even safer
since
> everything is on a nice flat surface and not being held vertically.
A couple of questions if I may ask about using a vertical bit.
How high a fence are you using? Did you have to adjust the height of the
fence the first few times you used a vertical panel bit?
Did you first use a regular flat panel bit and then go to the vertical bit?
What prompted you to do so?
Doing the best cut you can with both bits, what if any differences do you
notice between the vertical and flat panel bits, either the way they cut or
the finish achieved?
Thanks