This is my original post:
> I made a bar/counter top out of birds-eye maple and paduk. It
> involves 4 pieces of the maple and 2 strips of the paduk, all edge
> glued together. Anyway, it is ~ 25" x 74" and now I would like to
> sand it smooth. As I don't have a drum sander, and won=92t get one
> past the finance committee, I am wondering what the most efficient way
> would be. I do have a RO sander, but even with 60 grit on it, it is
> taking a long time to get anywhere. Would a belt sander be a better
> way to go? If so, what would be the best technique to use as I have
> not worked with one before?
> Thanks,
> Jim
I just wanted to start a different thread and get some attention to
it as I need to get it done.
Thanks,
-Jim
On Sat, 10 Jan 2009 15:52:29 +0000, jtpr wrote
(in article
<43e045d1-068f-478b-803c-29b8ee200c97@r32g2000vba.googlegroups.com>):
> This is my original post:
>> I made a bar/counter top out of birds-eye maple and paduk. It
>> involves 4 pieces of the maple and 2 strips of the paduk, all edge
>> glued together. Anyway, it is ~ 25" x 74" and now I would like to
>> sand it smooth. As I don't have a drum sander, and wont get one
>> past the finance committee, I am wondering what the most efficient way
>> would be. I do have a RO sander, but even with 60 grit on it, it is
>> taking a long time to get anywhere. Would a belt sander be a better
>> way to go? If so, what would be the best technique to use as I have
>> not worked with one before?
>
>> Thanks,
>> Jim
>
> I just wanted to start a different thread and get some attention to
> it as I need to get it done.
>
> Thanks,
> -Jim
Friend o'mine just flattened up a huge glue-up with a floor sander. Took off
LOADS of stuff. Not my choice. Seemed to work well, though.
Anyway - how much stuff you wanna remove, i.e.is this a "planing" rather than
a 'sanding job? If so, the old router-on-rails trick might do it of you don't
mind the tedium
If it's just smoothing a flat surface.. wax on, wax off dear pupil.
Elbow grease and patience. (personally I'd use a belt, but I'd go finer on
the grit and KEEP IT MOVING. Diagonal to the grain.)
More cleverer folk may have more cleverer advice. Use their wisdom and profit
by it.
On Sat, 10 Jan 2009 07:52:29 -0800 (PST), jtpr <[email protected]>
wrote:
>This is my original post:
>> I made a bar/counter top out of birds-eye maple and paduk. It
>> involves 4 pieces of the maple and 2 strips of the paduk, all edge
>> glued together. Anyway, it is ~ 25" x 74" and now I would like to
>> sand it smooth. As I don't have a drum sander, and wont get one
>> past the finance committee, I am wondering what the most efficient way
>> would be. I do have a RO sander, but even with 60 grit on it, it is
>> taking a long time to get anywhere. Would a belt sander be a better
>> way to go? If so, what would be the best technique to use as I have
>> not worked with one before?
>
>> Thanks,
>> Jim
>
>I just wanted to start a different thread and get some attention to
>it as I need to get it done.
>
>Thanks,
>-Jim
Jim,
First thing that I would try is looking up woodworking and furniture
repair in the yellow pages. If the places you call can't do the work,
they might be able to point you to someone who can. I've had pretty
good luck with this approach to problems in the past.
Bill