BS says it all.
I have a bunch of blades that I need to replace.
Most of my narrower blades are Olson's.
According the box, I saved one years ago, the width of a blade is
measured from the tip of the tooth to the back of the blade.
REALLY!!! someone should tell OLSON that.
My 1/2 Olson measures nearly 5/8.
My 1/4 closer to 3/8.
My opinion of Olson blades has been pretty low, they just keep giving me
reason to lower that opinion.
The 1/2 measures 1/2 to the gullet not the tooth. WTF is wrong with them.
Their packaging, their sizing doc...
--
Jeff
On Saturday, January 23, 2016 at 2:09:16 PM UTC-6, woodchucker wrote:
> BS says it all.
> I have a bunch of blades that I need to replace.
> Most of my narrower blades are Olson's.
>
> According the box, I saved one years ago, the width of a blade is
> measured from the tip of the tooth to the back of the blade.
>
> REALLY!!! someone should tell OLSON that.
> My 1/2 Olson measures nearly 5/8.
> My 1/4 closer to 3/8.
> My opinion of Olson blades has been pretty low, they just keep giving me
> reason to lower that opinion.
>
> The 1/2 measures 1/2 to the gullet not the tooth. WTF is wrong with them.
> Their packaging, their sizing doc...
>
> --
> Jeff
Have either of you tried the Highland Hardware General Purpose Bandsaw blade? Most of the time, there is no need to adjust for drift. That cannot be said of any of the other blades I have used.
http://www.highlandwoodworking.com/general-purpose-bandsaw-blades.aspx
Deb
woodchucker <[email protected]> wrote:
> On 1/30/2016 7:57 PM, Electric Comet wrote:
>> On Sat, 23 Jan 2016 15:09:06 -0500
>> woodchucker <[email protected]> wrote:
>>
>>> According the box, I saved one years ago, the width of a blade is
>>> measured from the tip of the tooth to the back of the blade.
>>
>> i bought the ones hanging on the wall and so no box to misinterpret
>>
>> not sure who made them
>>
>> they were the right length and right tpi
>>
>> does the fact they boxes do not agree bother you or the actual dimensions
>> that are wrong for your application
>>
>>
>>
>>
> No, I just needed to know what size blades are broken to replace them.
> I just pick a blade that looks right for the job.
>
> So now that I need to replace them, I need to know what size they are.
> And when I realized that even my 1/2 blade did not measure 1/2, I
> question my understanding of what blades I need to buy.. since none
> really matched what the box said.
>
> Do I order 1/4 or 3/8
> do I order 3/16 or 1/8 you get the picture don't you.
>
>
> So what do I buy??? I guess I can take a trip 1 hour a way to Woodcraft
> and sit there with my old blades, and compare.. but that seems stupid.
>
>
Here is a link with a chart to determine how to pick the correct size
blade, or call.
http://www.allbandsawblades.com/blade_width.htm
On Sun, 31 Jan 2016 14:51:54 -0500, Ed Pawlowski <[email protected]> wrote:
>On 1/31/2016 12:49 PM, woodchucker wrote:
>
>>>
>> No, I just needed to know what size blades are broken to replace them.
>> I just pick a blade that looks right for the job.
>>
>> So now that I need to replace them, I need to know what size they are.
>> And when I realized that even my 1/2 blade did not measure 1/2, I
>> question my understanding of what blades I need to buy.. since none
>> really matched what the box said.
>>
>> Do I order 1/4 or 3/8
>> do I order 3/16 or 1/8 you get the picture don't you.
>>
>>
>> So what do I buy??? I guess I can take a trip 1 hour a way to Woodcraft
>> and sit there with my old blades, and compare.. but that seems stupid.
>>
>>
>
>What part is stupid? The driving 1 hour or comparing blades?
>
>I'd take my wife to lunch at a nice place near Woodcraft. She would
>take her Kindle and read while I'm in Woodcraft BSing with the guys there.
>
>For us, it would not be a chore but a nice day out. Semi-retired, we
>often go out to lunch an hour or two from home on my day off. I guess YMWV
We do the woodworking tour of Atlanta (Rockler, Woodcraft, Peachtree,
and Highland) about every six to eight weeks. I'll drop SWMBO off at
one of the nicer outdoor malls while I do Woodcraft and we stop at
other places she likes to browse along the way. She likes Highland,
though. It's a really neat place (with all sorts of toys on display).
On 2/1/2016 8:19 PM, woodchucker wrote:
> On 2/1/2016 8:45 AM, Leon wrote:
>> woodchucker <[email protected]> wrote:
>>> On 1/30/2016 7:57 PM, Electric Comet wrote:
>>>> On Sat, 23 Jan 2016 15:09:06 -0500
>>>> woodchucker <[email protected]> wrote:
>>>>
>>>>> According the box, I saved one years ago, the width of a blade is
>>>>> measured from the tip of the tooth to the back of the blade.
>>>>
>>>> i bought the ones hanging on the wall and so no box to misinterpret
>>>>
>>>> not sure who made them
>>>>
>>>> they were the right length and right tpi
>>>>
>>>> does the fact they boxes do not agree bother you or the actual
>>>> dimensions
>>>> that are wrong for your application
>>>>
>>>>
>>>>
>>>>
>>> No, I just needed to know what size blades are broken to replace them.
>>> I just pick a blade that looks right for the job.
>>>
>>> So now that I need to replace them, I need to know what size they are.
>>> And when I realized that even my 1/2 blade did not measure 1/2, I
>>> question my understanding of what blades I need to buy.. since none
>>> really matched what the box said.
>>>
>>> Do I order 1/4 or 3/8
>>> do I order 3/16 or 1/8 you get the picture don't you.
>>>
>>>
>>> So what do I buy??? I guess I can take a trip 1 hour a way to Woodcraft
>>> and sit there with my old blades, and compare.. but that seems stupid.
>>>
>>>
>>
>> Here is a link with a chart to determine how to pick the correct size
>> blade, or call.
>>
>> http://www.allbandsawblades.com/blade_width.htm
>>
>>
> I don't need to know what size cuts what curve, what I need to figure
> out what I broke and need to replace.
Take a look at the site and you will see that it also shows you how to
measure the blade.
On 2/1/2016 8:45 AM, Leon wrote:
> woodchucker <[email protected]> wrote:
>> On 1/30/2016 7:57 PM, Electric Comet wrote:
>>> On Sat, 23 Jan 2016 15:09:06 -0500
>>> woodchucker <[email protected]> wrote:
>>>
>>>> According the box, I saved one years ago, the width of a blade is
>>>> measured from the tip of the tooth to the back of the blade.
>>>
>>> i bought the ones hanging on the wall and so no box to misinterpret
>>>
>>> not sure who made them
>>>
>>> they were the right length and right tpi
>>>
>>> does the fact they boxes do not agree bother you or the actual dimensions
>>> that are wrong for your application
>>>
>>>
>>>
>>>
>> No, I just needed to know what size blades are broken to replace them.
>> I just pick a blade that looks right for the job.
>>
>> So now that I need to replace them, I need to know what size they are.
>> And when I realized that even my 1/2 blade did not measure 1/2, I
>> question my understanding of what blades I need to buy.. since none
>> really matched what the box said.
>>
>> Do I order 1/4 or 3/8
>> do I order 3/16 or 1/8 you get the picture don't you.
>>
>>
>> So what do I buy??? I guess I can take a trip 1 hour a way to Woodcraft
>> and sit there with my old blades, and compare.. but that seems stupid.
>>
>>
>
> Here is a link with a chart to determine how to pick the correct size
> blade, or call.
>
> http://www.allbandsawblades.com/blade_width.htm
>
>
I don't need to know what size cuts what curve, what I need to figure
out what I broke and need to replace.
--
Jeff
On Saturday, January 23, 2016 at 2:09:16 PM UTC-6, woodchucker wrote:
> BS says it all.
> I have a bunch of blades that I need to replace.
> Most of my narrower blades are Olson's.
>=20
> According the box, I saved one years ago, the width of a blade is=20
> measured from the tip of the tooth to the back of the blade.
>=20
> REALLY!!! someone should tell OLSON that.
> My 1/2 Olson measures nearly 5/8.
> My 1/4 closer to 3/8.
> My opinion of Olson blades has been pretty low, they just keep giving me=
=20
> reason to lower that opinion.
>=20
> The 1/2 measures 1/2 to the gullet not the tooth. WTF is wrong with them=
.
> Their packaging, their sizing doc...
>=20
> --=20
> Jeff
I have tried, Olson, Timberwolf, Carter and some off brands. The absolute =
best blade I have found yet is the house brand from Highland Hardware. Not=
their Woodslicer, which is a great resaw blade, or their wet wood blades b=
ut their standard house brand bandsaw blade.
Which reminds me, I need to order a couple more.
Deb
A regular toothbrush...anything harder or more coarse is likely to damage the tire on the wheel...Should only be just touching, not bearing down, so as to knock off the collected sawdust...
On Tuesday, February 2, 2016 at 10:51:35 PM UTC-5, Electric Comet wrote:
> On Tue, 2 Feb 2016 18:23:58 -0500
> woodchucker <[email protected]> wrote:
>
> > I've never seen them.
>
> me neither but have not looked hard
>
> > BTW stick a toothbrush on a piece of metal, mount it and keep the
> > wheel clean.
>
> interesting and that sounds like a good idea
>
> does a regular old toothbrush suffice
>
> i have some similar sized copper or stainless brushes
>
> > Also add dust collection, it keeps the tires from loading up and
> > adding pitch and sawdust into the tire. Even the urethanes get messy
> > if you don't have even a brush. while not perfect, it works better
> > than no brush.
>
> have this already
> the tires are going to get messy since i cut messy stuff
>
> my problem now is that i need to get something bigger
Electric Comet <[email protected]> wrote in news:n8tlo0$js5$2
@dont-email.me:
> On Wed, 3 Feb 2016 10:30:38 -0800 (PST)
> [email protected] wrote:
>
>> A regular toothbrush...anything harder or more coarse is likely to
>> damage the tire on the wheel...Should only be just touching, not
>> bearing down, so as to knock off the collected sawdust...
>
> i am going to do this for sure
>
> now i wonder if there is a pre-made one for delta 14 inch saws since
> there are so many deltas
Quit wondering... Go search. "Bandsaw wheel brush" should turn up some
good results.
Puckdropper
woodchucker <[email protected]> wrote:
> On 2/2/2016 10:50 PM, Electric Comet wrote:
>> On Tue, 2 Feb 2016 18:23:58 -0500
>> woodchucker <[email protected]> wrote:
>>
>>> I've never seen them.
>>
>> me neither but have not looked hard
>>
>>> BTW stick a toothbrush on a piece of metal, mount it and keep the
>>> wheel clean.
>>
>> interesting and that sounds like a good idea
>>
>> does a regular old toothbrush suffice
>>
>> i have some similar sized copper or stainless brushes
>>
>>> Also add dust collection, it keeps the tires from loading up and
>>> adding pitch and sawdust into the tire. Even the urethanes get messy
>>> if you don't have even a brush. while not perfect, it works better
>>> than no brush.
>>
>> have this already
>> the tires are going to get messy since i cut messy stuff
>>
>> my problem now is that i need to get something bigger
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
> I would not use copper or stainless brushes, only hair or nylon bristles.
>
Laguna uses what appears to be a cut up section of a straw push broom.
On 1/25/2016 1:13 PM, Kevin Miller wrote:
> On 01/23/2016 11:09 AM, woodchucker wrote:
>> BS says it all.
>> I have a bunch of blades that I need to replace.
>> Most of my narrower blades are Olson's.
>>
>> According the box, I saved one years ago, the width of a blade is
>> measured from the tip of the tooth to the back of the blade.
>>
>> REALLY!!! someone should tell OLSON that.
>> My 1/2 Olson measures nearly 5/8.
>> My 1/4 closer to 3/8.
>> My opinion of Olson blades has been pretty low, they just keep giving me
>> reason to lower that opinion.
>>
>> The 1/2 measures 1/2 to the gullet not the tooth. WTF is wrong with
>> them.
>> Their packaging, their sizing doc...
>
> I never bothered to measure them, but I've always been partial to
> Timberwolf blades direct from suffolkmachinery.com. You might give them
> a try...
>
> ...Kevin
They (TW) are my preffered blades for resawing.
I don't own thinner blades from them.
I am going to try the Highland woodslicer as I broke my timberwolf last
year and have been using old surplus of Olson's.. clearly not up to the
Timberwolfs.
--
Jeff
On 1/30/2016 7:57 PM, Electric Comet wrote:
> On Sat, 23 Jan 2016 15:09:06 -0500
> woodchucker <[email protected]> wrote:
>
>> According the box, I saved one years ago, the width of a blade is
>> measured from the tip of the tooth to the back of the blade.
>
> i bought the ones hanging on the wall and so no box to misinterpret
>
> not sure who made them
>
> they were the right length and right tpi
>
> does the fact they boxes do not agree bother you or the actual dimensions
> that are wrong for your application
>
>
>
>
No, I just needed to know what size blades are broken to replace them.
I just pick a blade that looks right for the job.
So now that I need to replace them, I need to know what size they are.
And when I realized that even my 1/2 blade did not measure 1/2, I
question my understanding of what blades I need to buy.. since none
really matched what the box said.
Do I order 1/4 or 3/8
do I order 3/16 or 1/8 you get the picture don't you.
So what do I buy??? I guess I can take a trip 1 hour a way to Woodcraft
and sit there with my old blades, and compare.. but that seems stupid.
--
Jeff
On 2/2/2016 10:50 PM, Electric Comet wrote:
> On Tue, 2 Feb 2016 18:23:58 -0500
> woodchucker <[email protected]> wrote:
>
>> I've never seen them.
>
> me neither but have not looked hard
>
>> BTW stick a toothbrush on a piece of metal, mount it and keep the
>> wheel clean.
>
> interesting and that sounds like a good idea
>
> does a regular old toothbrush suffice
>
> i have some similar sized copper or stainless brushes
>
>> Also add dust collection, it keeps the tires from loading up and
>> adding pitch and sawdust into the tire. Even the urethanes get messy
>> if you don't have even a brush. while not perfect, it works better
>> than no brush.
>
> have this already
> the tires are going to get messy since i cut messy stuff
>
> my problem now is that i need to get something bigger
>
>
>
>
>
>
>
>
>
I would not use copper or stainless brushes, only hair or nylon bristles.
--
Jeff
On 2/1/2016 1:13 PM, Electric Comet wrote:
> On Sun, 31 Jan 2016 12:49:30 -0500
> woodchucker <[email protected]> wrote:
>
>> Do I order 1/4 or 3/8
>> do I order 3/16 or 1/8 you get the picture don't you.
>
> yes
> good to know as i am a fairly recent owner of a bandsaw and the blades
> i have are all that was needed so far
>
> but i do not like changing the blades so i leave the one blade on
>
> until it cannot cut it
>
>
I found that doesn't work so well.
The right blade is worth the 3 or so minutes to change it.
--
Jeff
On 2/1/2016 11:23 PM, Leon wrote:
> On 2/1/2016 8:19 PM, woodchucker wrote:
>> On 2/1/2016 8:45 AM, Leon wrote:
>>> woodchucker <[email protected]> wrote:
>>>> On 1/30/2016 7:57 PM, Electric Comet wrote:
>>>>> On Sat, 23 Jan 2016 15:09:06 -0500
>>>>> woodchucker <[email protected]> wrote:
>>>>>
>>>>>> According the box, I saved one years ago, the width of a blade is
>>>>>> measured from the tip of the tooth to the back of the blade.
>>>>>
>>>>> i bought the ones hanging on the wall and so no box to misinterpret
>>>>>
>>>>> not sure who made them
>>>>>
>>>>> they were the right length and right tpi
>>>>>
>>>>> does the fact they boxes do not agree bother you or the actual
>>>>> dimensions
>>>>> that are wrong for your application
>>>>>
>>>>>
>>>>>
>>>>>
>>>> No, I just needed to know what size blades are broken to replace them.
>>>> I just pick a blade that looks right for the job.
>>>>
>>>> So now that I need to replace them, I need to know what size they are.
>>>> And when I realized that even my 1/2 blade did not measure 1/2, I
>>>> question my understanding of what blades I need to buy.. since none
>>>> really matched what the box said.
>>>>
>>>> Do I order 1/4 or 3/8
>>>> do I order 3/16 or 1/8 you get the picture don't you.
>>>>
>>>>
>>>> So what do I buy??? I guess I can take a trip 1 hour a way to
>>>> Woodcraft
>>>> and sit there with my old blades, and compare.. but that seems stupid.
>>>>
>>>>
>>>
>>> Here is a link with a chart to determine how to pick the correct size
>>> blade, or call.
>>>
>>> http://www.allbandsawblades.com/blade_width.htm
>>>
>>>
>> I don't need to know what size cuts what curve, what I need to figure
>> out what I broke and need to replace.
>
>
> Take a look at the site and you will see that it also shows you how to
> measure the blade.
Allright, I'll spend some time looking around.
--
Jeff
On 2/2/2016 11:23 AM, Electric Comet wrote:
> On Mon, 1 Feb 2016 21:25:00 -0500
> woodchucker <[email protected]> wrote:
>
>> I found that doesn't work so well.
>> The right blade is worth the 3 or so minutes to change it.
>
> takes me longer than that but i will get quicker at it in time
>
> like any other tool as it is used more and understood how it can be used
> and in what situations i will go to it more
>
> my next project is going to require a small blade so i can do some curves
>
> i am sure the tires need to be cleaned anyway
>
> since we are on blades i wonder if anyone makes a round blade for the
> bandsaw
>
> like they make for a scroll saw
>
> that would be useful for thinner stock i think but might eat up the tires
>
>
>
I've never seen them.
BTW stick a toothbrush on a piece of metal, mount it and keep the wheel
clean.
Also add dust collection, it keeps the tires from loading up and adding
pitch and sawdust into the tire. Even the urethanes get messy if you
don't have even a brush. while not perfect, it works better than no brush.
--
Jeff
woodchucker <[email protected]> wrote in news:EqKdnaSjgaHp-zvLnZ2dnUU7-
[email protected]:
> I am going to try the Highland woodslicer as I broke my timberwolf last
> year and have been using old surplus of Olson's.. clearly not up to the
> Timberwolfs.
My experience has been completely opposite that: I've gotten much better results on my saw
with Olson blades than with Timberwolf, to the point that I doubt I'll ever buy a TW blade again.
Leon <lcb11211@swbelldotnet> wrote in news:j4qdnY5caM7mDzrLnZ2dnUU7-
[email protected]:
[...]
> So for most people, they are going to have to simply hunt to find the
> brand that works best for them on their particular brand saw.
I agree. For me, on my 14" Delta, that seems to be Olson.
On 2/2/2016 5:24 PM, woodchucker wrote:
> On 2/1/2016 11:23 PM, Leon wrote:
>> On 2/1/2016 8:19 PM, woodchucker wrote:
>>> On 2/1/2016 8:45 AM, Leon wrote:
>>>> woodchucker <[email protected]> wrote:
>>>>> On 1/30/2016 7:57 PM, Electric Comet wrote:
>>>>>> On Sat, 23 Jan 2016 15:09:06 -0500
>>>>>> woodchucker <[email protected]> wrote:
>>>>>>
>>>>>>> According the box, I saved one years ago, the width of a blade is
>>>>>>> measured from the tip of the tooth to the back of the blade.
>>>>>>
>>>>>> i bought the ones hanging on the wall and so no box to misinterpret
>>>>>>
>>>>>> not sure who made them
>>>>>>
>>>>>> they were the right length and right tpi
>>>>>>
>>>>>> does the fact they boxes do not agree bother you or the actual
>>>>>> dimensions
>>>>>> that are wrong for your application
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>> No, I just needed to know what size blades are broken to replace them.
>>>>> I just pick a blade that looks right for the job.
>>>>>
>>>>> So now that I need to replace them, I need to know what size they are.
>>>>> And when I realized that even my 1/2 blade did not measure 1/2, I
>>>>> question my understanding of what blades I need to buy.. since none
>>>>> really matched what the box said.
>>>>>
>>>>> Do I order 1/4 or 3/8
>>>>> do I order 3/16 or 1/8 you get the picture don't you.
>>>>>
>>>>>
>>>>> So what do I buy??? I guess I can take a trip 1 hour a way to
>>>>> Woodcraft
>>>>> and sit there with my old blades, and compare.. but that seems stupid.
>>>>>
>>>>>
>>>>
>>>> Here is a link with a chart to determine how to pick the correct size
>>>> blade, or call.
>>>>
>>>> http://www.allbandsawblades.com/blade_width.htm
>>>>
>>>>
>>> I don't need to know what size cuts what curve, what I need to figure
>>> out what I broke and need to replace.
>>
>>
>> Take a look at the site and you will see that it also shows you how to
>> measure the blade.
> Allright, I'll spend some time looking around.
>
You will find the answer faster than responding to me. ;~)
On 01/23/2016 11:09 AM, woodchucker wrote:
> BS says it all.
> I have a bunch of blades that I need to replace.
> Most of my narrower blades are Olson's.
>
> According the box, I saved one years ago, the width of a blade is
> measured from the tip of the tooth to the back of the blade.
>
> REALLY!!! someone should tell OLSON that.
> My 1/2 Olson measures nearly 5/8.
> My 1/4 closer to 3/8.
> My opinion of Olson blades has been pretty low, they just keep giving me
> reason to lower that opinion.
>
> The 1/2 measures 1/2 to the gullet not the tooth. WTF is wrong with them.
> Their packaging, their sizing doc...
I never bothered to measure them, but I've always been partial to
Timberwolf blades direct from suffolkmachinery.com. You might give them
a try...
...Kevin
--
Kevin Miller
Juneau, Alaska
http://www.alaska.net/~atftb
"In the history of the world, no one has ever washed a rented car."
- Lawrence Summers
On 1/25/2016 7:36 PM, Doug Miller wrote:
> woodchucker <[email protected]> wrote in news:EqKdnaSjgaHp-zvLnZ2dnUU7-
> [email protected]:
>
>> I am going to try the Highland woodslicer as I broke my timberwolf last
>> year and have been using old surplus of Olson's.. clearly not up to the
>> Timberwolfs.
>
> My experience has been completely opposite that: I've gotten much better results on my saw
> with Olson blades than with Timberwolf, to the point that I doubt I'll ever buy a TW blade again.
>
I was in that camp for a while too. But you have to wonder how a company
could remain in the BS blade business if they were turning out crap.
I learned the hard way that it is the saw more than the blade.
I bought several Timberwolf blades for a new 18" Rokon BS about 9 years
ago and had trouble with 2/3's of the blades. Timberwolf even talked me
through cutting one of those blades and laying it out straight on my
garage floor to insure that it was straight. They asked the brand saw I
was using and indicated that they had been having issues with their
blades on those saws. I had a local shop make me a blade and it did
fine as did the blade that came with the saw. But no other blade worked
well consistently.
After reviewing several Laguna video's and what to look for in a BS I
ended up returning the Rikon and buying a Laguna. Timberwolf took all
the used blades back in exchange for the longer ones, 150" for the Laguna.
Now, with the Laguna, the no name freeby blades that came with the saw,
the Timberwolf, and the ResawKing all work exactly like they are suppose to.
So for most people, they are going to have to simply hunt to find the
brand that works best for them on their particular brand saw.
On Sat, 23 Jan 2016 15:09:06 -0500
woodchucker <[email protected]> wrote:
> According the box, I saved one years ago, the width of a blade is
> measured from the tip of the tooth to the back of the blade.
i bought the ones hanging on the wall and so no box to misinterpret
not sure who made them
they were the right length and right tpi
does the fact they boxes do not agree bother you or the actual dimensions
that are wrong for your application
On Sun, 31 Jan 2016 12:49:30 -0500
woodchucker <[email protected]> wrote:
> Do I order 1/4 or 3/8
> do I order 3/16 or 1/8 you get the picture don't you.
yes
good to know as i am a fairly recent owner of a bandsaw and the blades
i have are all that was needed so far
but i do not like changing the blades so i leave the one blade on
until it cannot cut it
On Mon, 1 Feb 2016 21:25:00 -0500
woodchucker <[email protected]> wrote:
> I found that doesn't work so well.
> The right blade is worth the 3 or so minutes to change it.
takes me longer than that but i will get quicker at it in time
like any other tool as it is used more and understood how it can be used
and in what situations i will go to it more
my next project is going to require a small blade so i can do some curves
i am sure the tires need to be cleaned anyway
since we are on blades i wonder if anyone makes a round blade for the
bandsaw
like they make for a scroll saw
that would be useful for thinner stock i think but might eat up the tires
On Tue, 2 Feb 2016 18:23:58 -0500
woodchucker <[email protected]> wrote:
> I've never seen them.
me neither but have not looked hard
> BTW stick a toothbrush on a piece of metal, mount it and keep the
> wheel clean.
interesting and that sounds like a good idea
does a regular old toothbrush suffice
i have some similar sized copper or stainless brushes
> Also add dust collection, it keeps the tires from loading up and
> adding pitch and sawdust into the tire. Even the urethanes get messy
> if you don't have even a brush. while not perfect, it works better
> than no brush.
have this already
the tires are going to get messy since i cut messy stuff
my problem now is that i need to get something bigger
On Wed, 3 Feb 2016 12:42:12 -0500
woodchucker <[email protected]> wrote:
> I would not use copper or stainless brushes, only hair or nylon
> bristles.
roger wilco
On Wed, 3 Feb 2016 10:30:38 -0800 (PST)
[email protected] wrote:
> A regular toothbrush...anything harder or more coarse is likely to
> damage the tire on the wheel...Should only be just touching, not
> bearing down, so as to knock off the collected sawdust...
i am going to do this for sure
now i wonder if there is a pre-made one for delta 14 inch saws since
there are so many deltas
On 1/31/2016 12:49 PM, woodchucker wrote:
>>
> No, I just needed to know what size blades are broken to replace them.
> I just pick a blade that looks right for the job.
>
> So now that I need to replace them, I need to know what size they are.
> And when I realized that even my 1/2 blade did not measure 1/2, I
> question my understanding of what blades I need to buy.. since none
> really matched what the box said.
>
> Do I order 1/4 or 3/8
> do I order 3/16 or 1/8 you get the picture don't you.
>
>
> So what do I buy??? I guess I can take a trip 1 hour a way to Woodcraft
> and sit there with my old blades, and compare.. but that seems stupid.
>
>
What part is stupid? The driving 1 hour or comparing blades?
I'd take my wife to lunch at a nice place near Woodcraft. She would
take her Kindle and read while I'm in Woodcraft BSing with the guys there.
For us, it would not be a chore but a nice day out. Semi-retired, we
often go out to lunch an hour or two from home on my day off. I guess YMWV