Am I wrong or are parallel clamps supposed to be parallel?
On my Jets, the end clamp section tilts in a bit and the adjustable end
tilts in a bit (1/32-1/16"), after tightening.
Is there an adjustment procedure with these or are parallel clamps just
supposed to be "close to parallel?"
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
On Wed, 24 Mar 2010 16:49:21 -0500, Swingman <[email protected]> wrote:
>My Bessey's are close enough not to worry about, and the results have so
>far been perfect enough. :)
Think I remember reading that the jaw faces aren't completely parallel
until they're clamped down at which point they do align forming a
perfectly square clamping surface.
On Mar 25, 9:55=A0am, "[email protected]" <[email protected]> wrote:
> On Mar 25, 11:16=A0am, "Leon" <[email protected]> wrote:> <keith...@=
gmail.com> wrote in message
>
> >news:7fe1d981-7832-4fe4-82ed-58cb0909f6b0@g10g2000yqh.googlegroups.com..=
.
> > On Mar 25, 9:00 am, "[email protected]" <[email protected]>
>
> > > When I glue something up in the field that requires this kind of
> > > clamping, I actually level my "table" on the sawhorses by carefully
> > > leveling the material I am using for a top.
>
> > > This cuts out most of the problems.
>
> > Level or planar? =A0How level is level? =A0I see vertical glue-up jigs.
> > How do they work?
>
> > When clamping up water boards the surface absolutely myst be "Level".
>
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0????????????
>
> What is a "water board"?
Similar to a henway
On Mar 25, 7:20=A0am, "Leon" <[email protected]> wrote:
> I have Jet, Bessey, and Cabinet Master parallel clamps. =A0None of them a=
re
> parallel at some stage of tightening and or depending on the opening on t=
he
> clamps. =A0Simply put, the bar will bend and that prevents the consistant
> possibility of a perfectly parallel set of jaw faces. =A0
Mine aren't perfect, but they are close enough. I have a million
clamps, and to fight off the fact that they all twist a bit
(Besseys.... not much, though) I use a lot of clamps and a little
pressure.
> BUT these type clamps
> tend to work about as good as you could expect.
I think so. Most of the time when you see twisting or wracking it can
be minimized by reorienting the victims in the clamps.
However, when teaching others the art of the glue up, almost without
fail the most likely culprit in their glue up failure is placing the
clamps and material on an uneven surface to glue up. And uneven table
top, gluing on saw horses, etc., bring a whole different dimension non
parallel clamps.
When I glue something up in the field that requires this kind of
clamping, I actually level my "table" on the sawhorses by carefully
leveling the material I am using for a top.
This cuts out most of the problems.
Robert
"Leon" <[email protected]> wrote in
news:[email protected]:
>
>
> Where do you race? Me, I'm a typist. ;~)
>
>
Do you type with both hands at the same time? Then you're a stereo typist.
Puckdropper
--
Never teach your apprentice everything you know.
On 3/27/2010 12:25 PM, Leon wrote:
> thumb and right 2 fingers. I'd probably type with my left thumb if it were
> normal length. An alteration I made on it 20 years ago left it short. ;~)
You know what they say - Measure twice, cut once ... <g,d & r>
--
www.e-woodshop.net
Last update: 10/22/08
KarlC@ (the obvious)
"Larry Jaques" <[email protected]> wrote in message
news:[email protected]...
> On Thu, 25 Mar 2010 22:17:59 -0700 (PDT), the infamous
> "[email protected]" <[email protected]> scrawled the
>
> It couldn't be. I'm a racist. Lew said so. <g>
Where do you race? Me, I'm a typist. ;~)
On Thu, 25 Mar 2010 22:17:59 -0700 (PDT), the infamous
"[email protected]" <[email protected]> scrawled the
following:
>On Mar 25, 9:46 pm, Larry Jaques <[email protected]> wrote:
>
>> It's sheer torture, isn't it? <giggle>
>>
>> --
>> Challenges are gifts that force us to search for a new center of gravity.
>> Don't fight them. Just find a different way to stand.
>> -- Oprah Winfrey
>
>WHAT'S THIS?
>
>LJ quoting OPRAH's life lessons???
>
>OUCH!
It couldn't be. I'm a racist. Lew said so. <g>
--
"Not always right, but never uncertain." --Heinlein
-=-=-
"Lee Michaels" <leemichaels*nadaspam*@comcast.net> wrote in message
news:[email protected]...
>
> "Leon" wrote
>>
>> Where do you race? Me, I'm a typist. ;~)
> With a true talent and flair for typos. ;-)
>
>
>
Yeah there is that 2. ;~) I can't afford a spell checher that can read my
mind yet.
"Puckdropper" <puckdropper(at)yahoo(dot)com> wrote in message
news:[email protected]...
> "Leon" <[email protected]> wrote in
> news:[email protected]:
>
>>
>>
>> Where do you race? Me, I'm a typist. ;~)
>>
>>
>
> Do you type with both hands at the same time? Then you're a stereo
> typist.
I think I am a stereo pecker. ;~) Looooooooooooooooong a go I typed "good
enough". My son is about 90 words per minute. He has indicated that he has
never seen any one type as fast as me using only 2 left fingers and my right
thumb and right 2 fingers. I'd probably type with my left thumb if it were
normal length. An alteration I made on it 20 years ago left it short. ;~)
On Mar 24, 3:38=A0pm, -MIKE- <[email protected]> wrote:
> Am I wrong or are parallel clamps supposed to be parallel?
> On my Jets, the end clamp section tilts in a bit and the adjustable end
> tilts in a bit (1/32-1/16"), after tightening.
>
> Is there an adjustment procedure with these or are parallel clamps just
> supposed to be "close to parallel?"
On topic, but ... next to irrelevant:
My set of four Jets arrived today -- 2 @ 24", 2 @ 40"
The latest special "Tools & Shops" issue of FWW put them at #1 --
above Bessey, Jorgensen, and all other comers.
Here's hoping!
<[email protected]> wrote
> Most of the time when you see twisting or wracking it can
>be minimized by reorienting the victims in the clamps.
>However, when teaching others the art of the glue up, almost without
>fail the most likely culprit in their glue up failure is placing the
>clamps and material on an uneven surface to glue up. And uneven table
>top, gluing on saw horses, etc., bring a whole different dimension non
>parallel clamps.
>When I glue something up in the field that requires this kind of
>clamping, I actually level my "table" on the sawhorses by carefully
>leveling the material I am using for a top.
>This cuts out most of the problems.
>Robert
Bingo. It took me awhile to learn that but once I did it solved a lot of
frustration.
I built an assembly table with legs that could be adjusted to level.
Max
"blueman" <[email protected]> wrote in message
news:[email protected]...
> "Max" <[email protected]> writes:
>> <[email protected]> wrote
>>
>>> Most of the time when you see twisting or wracking it can
>>>be minimized by reorienting the victims in the clamps.
>>
>>>However, when teaching others the art of the glue up, almost without
>>>fail the most likely culprit in their glue up failure is placing the
>>>clamps and material on an uneven surface to glue up. And uneven table
>>>top, gluing on saw horses, etc., bring a whole different dimension non
>>>parallel clamps.
>>
>>>When I glue something up in the field that requires this kind of
>>>clamping, I actually level my "table" on the sawhorses by carefully
>>>leveling the material I am using for a top.
>>
>>>This cuts out most of the problems.
>>
>>>Robert
>>
>> Bingo. It took me awhile to learn that but once I did it solved a lot
>> of frustration.
>> I built an assembly table with legs that could be adjusted to level.
>>
>> Max
>
> Is that really necessary?
> I just have been using a 1/2 sheet of 3/4" plywood that is pretty darn
> flat so that all ends of each parallel clamp rest on the same flat
> surface. Then in turn the bases of each clamp are paralle to this
> surface as is the piece being clamped.
>
> Within reason, it doesn't matter whether this plywood top is level with
> the ground or not as long as all clamps fully rest on its surface...
>
> Am I missing something?
The concrete floor in my shop is not.........uh........shall we say,
"perfect".
I have a 3' X 5' assembly table. It consists of an angle iron frame onto
which I fastened a piece of MDO. While I don't "level" the table with
respect to the earth, I do adjust the legs to take care of a corner that may
be a bit low. I just want the table to be *flat*.
Maybe I should explain that almost everything in my shop is moveable.
(casters, etc) I can arrange tools to accommodate different activities,
woodworking, metalworking, appliance repair, auto repair..........whatever
the need. So the table may be in a different location depending on the task
at hand.
Max
On Wed, 24 Mar 2010 16:38:59 -0500, -MIKE- wrote:
> Am I wrong or are parallel clamps supposed to be parallel? On my Jets,
> the end clamp section tilts in a bit and the adjustable end tilts in a
> bit (1/32-1/16"), after tightening.
>
> Is there an adjustment procedure with these or are parallel clamps just
> supposed to be "close to parallel?"
The description of some parallel clamps (I think they were Blessy)
in one of the woodworking catalogs says that the adjustable end is
tilted 1.5 degrees. Probably so that pressure equalizes along the
face of the clamp when it is drawn tight.
--
Mike Eager
On Thu, 25 Mar 2010 16:25:15 -0500, "Leon" <[email protected]> wrote:
>
><[email protected]> wrote in message
>news:ffeb0697-26d2-4e90-a244-5c4ff3f3b53e@k19g2000yqn.googlegroups.com...
>On Mar 25, 11:16 am, "Leon" <[email protected]> wrote:
>> <[email protected]> wrote in message
>>
>> news:7fe1d981-7832-4fe4-82ed-58cb0909f6b0@g10g2000yqh.googlegroups.com...
>> On Mar 25, 9:00 am, "[email protected]" <[email protected]>
>>
>> > When I glue something up in the field that requires this kind of
>> > clamping, I actually level my "table" on the sawhorses by carefully
>> > leveling the material I am using for a top.
>>
>> > This cuts out most of the problems.
>>
>> Level or planar? How level is level? I see vertical glue-up jigs.
>> How do they work?
>>
>> When clamping up water boards the surface absolutely myst be "Level".
> ????????????
>
>What is a "water board"?
>
>Don't you watch the news?
Silly me. I thought we were talking about woodworking, for once.
On Mar 25, 9:00=A0am, "[email protected]" <[email protected]>
wrote:
> On Mar 25, 7:20=A0am, "Leon" <[email protected]> wrote:
>
> > I have Jet, Bessey, and Cabinet Master parallel clamps. =A0None of them=
are
> > parallel at some stage of tightening and or depending on the opening on=
the
> > clamps. =A0Simply put, the bar will bend and that prevents the consista=
nt
> > possibility of a perfectly parallel set of jaw faces. =A0
>
> Mine aren't perfect, but they are close enough. =A0I have a million
> clamps, and to fight off the fact that they all twist a bit
> (Besseys.... not much, though) I use a lot of clamps and a little
> pressure.
>
> > BUT these type clamps
> > tend to work about as good as you could expect.
>
> I think so. =A0Most of the time when you see twisting or wracking it can
> be minimized by reorienting the victims in the clamps.
>
> However, when teaching others the art of the glue up, almost without
> fail the most likely culprit in their glue up failure is placing the
> clamps and material on an uneven surface to glue up. =A0And uneven table
> top, gluing on saw horses, etc., bring a whole different dimension non
> parallel clamps.
>
> When I glue something up in the field that requires this kind of
> clamping, I actually level my "table" on the sawhorses by carefully
> leveling the material I am using for a top.
>
> This cuts out most of the problems.
Level or planar? How level is level? I see vertical glue-up jigs.
How do they work?
On Mar 25, 9:46 pm, Larry Jaques <[email protected]> wrote:
> It's sheer torture, isn't it? <giggle>
>
> --
> Challenges are gifts that force us to search for a new center of gravity.
> Don't fight them. Just find a different way to stand.
> -- Oprah Winfrey
WHAT'S THIS?
LJ quoting OPRAH's life lessons???
OUCH!
Robert
Is this with a load or without?
I could suspect that under load they might square up. I could also
suspect that under load they could deflect. So I am covered either way
and should come out looking pretty smart.
On Mar 24, 2:38=A0pm, -MIKE- <[email protected]> wrote:
> Am I wrong or are parallel clamps supposed to be parallel?
> On my Jets, the end clamp section tilts in a bit and the adjustable end
> tilts in a bit (1/32-1/16"), after tightening.
>
> Is there an adjustment procedure with these or are parallel clamps just
> supposed to be "close to parallel?"
>
> --
>
> =A0 -MIKE-
>
> =A0 "Playing is not something I do at night, it's my function in life"
> =A0 =A0 =A0--Elvin Jones =A0(1927-2004)
> =A0 --
> =A0http://mikedrums.com
> =A0 [email protected]
> =A0 ---remove "DOT" ^^^^ to reply
<[email protected]> wrote in message
news:0f026d40-cfe5-4852-9271-c58a4eb6f58f@q15g2000yqj.googlegroups.com...
On Mar 25, 7:20 am, "Leon" <[email protected]> wrote:
Snip
When I glue something up in the field that requires this kind of
clamping, I actually level my "table" on the sawhorses by carefully
leveling the material I am using for a top.
This cuts out most of the problems.
99% of my clamping takes place in the shop, the TS top typically is the
flattest surface and therefore is my glue up table. :)
"-MIKE-" <[email protected]> wrote in message
news:[email protected]...
> Am I wrong or are parallel clamps supposed to be parallel?
> On my Jets, the end clamp section tilts in a bit and the adjustable end
> tilts in a bit (1/32-1/16"), after tightening.
>
> Is there an adjustment procedure with these or are parallel clamps just
> supposed to be "close to parallel?"
>
>
> --
>
> -MIKE-
>
> "Playing is not something I do at night, it's my function in life"
> --Elvin Jones (1927-2004)
> --
> http://mikedrums.com
> [email protected]
> ---remove "DOT" ^^^^ to reply
I have Jet, Bessey, and Cabinet Master parallel clamps. None of them are
parallel at some stage of tightening and or depending on the opening on the
clamps. Simply put, the bar will bend and that prevents the consistant
possibility of a perfectly parallel set of jaw faces. BUT these type clamps
tend to work about as good as you could expect.
On 03/24/2010 03:38 PM, -MIKE- wrote:
> Am I wrong or are parallel clamps supposed to be parallel?
> On my Jets, the end clamp section tilts in a bit and the adjustable end
> tilts in a bit (1/32-1/16"), after tightening.
>
> Is there an adjustment procedure with these or are parallel clamps just
> supposed to be "close to parallel?"
Ideally they should be parallel. There is no adjustment.
Taunten recently did a review of parallel jaw clamps. Some of them were
noticeably better than others at keeping parallel under load.
Chris
On 3/26/2010 1:14 AM, blueman wrote:
> Is that really necessary?
> Within reason, it doesn't matter whether this plywood top is level with
> the ground or not as long as all clamps fully rest on its surface...
>
> Am I missing something?
Yep ... the quotations around the word "level" in Robert's post.
The phrase "on the same level" comes immediately to mind ...
--
www.e-woodshop.net
Last update: 10/22/08
KarlC@ (the obvious)
On Mar 25, 11:16=A0am, "Leon" <[email protected]> wrote:
> <[email protected]> wrote in message
>
> news:7fe1d981-7832-4fe4-82ed-58cb0909f6b0@g10g2000yqh.googlegroups.com...
> On Mar 25, 9:00 am, "[email protected]" <[email protected]>
>
> > When I glue something up in the field that requires this kind of
> > clamping, I actually level my "table" on the sawhorses by carefully
> > leveling the material I am using for a top.
>
> > This cuts out most of the problems.
>
> Level or planar? =A0How level is level? =A0I see vertical glue-up jigs.
> How do they work?
>
> When clamping up water boards the surface absolutely myst be "Level".
????????????
What is a "water board"?
On 3/24/2010 4:38 PM, -MIKE- wrote:
> Am I wrong or are parallel clamps supposed to be parallel?
> On my Jets, the end clamp section tilts in a bit and the adjustable end
> tilts in a bit (1/32-1/16"), after tightening.
>
> Is there an adjustment procedure with these or are parallel clamps just
> supposed to be "close to parallel?"
Considering that a clamp of that type is not machined, nor has the
production engineering methodology for precise tolerances, "close"
probably counts.
My Bessey's are close enough not to worry about, and the results have so
far been perfect enough. :)
Now, when Festool starts making parallel jaw clamps ....
--
www.e-woodshop.net
Last update: 10/22/08
KarlC@ (the obvious)
On 3/24/10 5:11 PM, SonomaProducts.com wrote:
> Is this with a load or without?
>
Both.
> I could suspect that under load they might square up.
>
I thought so, too, but they didn't.
> I could also
> suspect that under load they could deflect.
> So I am covered either way
> and should come out looking pretty smart.
>
Funny.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
"Max" <[email protected]> writes:
> <[email protected]> wrote
>
>> Most of the time when you see twisting or wracking it can
>>be minimized by reorienting the victims in the clamps.
>
>>However, when teaching others the art of the glue up, almost without
>>fail the most likely culprit in their glue up failure is placing the
>>clamps and material on an uneven surface to glue up. And uneven table
>>top, gluing on saw horses, etc., bring a whole different dimension non
>>parallel clamps.
>
>>When I glue something up in the field that requires this kind of
>>clamping, I actually level my "table" on the sawhorses by carefully
>>leveling the material I am using for a top.
>
>>This cuts out most of the problems.
>
>>Robert
>
> Bingo. It took me awhile to learn that but once I did it solved a lot
> of frustration.
> I built an assembly table with legs that could be adjusted to level.
>
> Max
Is that really necessary?
I just have been using a 1/2 sheet of 3/4" plywood that is pretty darn
flat so that all ends of each parallel clamp rest on the same flat
surface. Then in turn the bases of each clamp are paralle to this
surface as is the piece being clamped.
Within reason, it doesn't matter whether this plywood top is level with
the ground or not as long as all clamps fully rest on its surface...
Am I missing something?
<[email protected]> wrote in message
news:7fe1d981-7832-4fe4-82ed-58cb0909f6b0@g10g2000yqh.googlegroups.com...
On Mar 25, 9:00 am, "[email protected]" <[email protected]>
> When I glue something up in the field that requires this kind of
> clamping, I actually level my "table" on the sawhorses by carefully
> leveling the material I am using for a top.
>
> This cuts out most of the problems.
Level or planar? How level is level? I see vertical glue-up jigs.
How do they work?
When clamping up water boards the surface absolutely myst be "Level".
On Fri, 26 Mar 2010 23:25:40 -0400, the infamous "Lee Michaels"
<leemichaels*nadaspam*@comcast.net> scrawled the following:
>
>"Leon" wrote
>>
>> Where do you race? Me, I'm a typist. ;~)
>With a true talent and flair for typos. ;-)
I think he INVENTED them, Lee. ;/
--
"Not always right, but never uncertain." --Heinlein
-=-=-
On Thu, 25 Mar 2010 17:49:18 -0500, the infamous
"[email protected]" <[email protected]> scrawled the
following:
>On Thu, 25 Mar 2010 16:25:15 -0500, "Leon" <[email protected]> wrote:
>
>>
>><[email protected]> wrote in message
>>news:ffeb0697-26d2-4e90-a244-5c4ff3f3b53e@k19g2000yqn.googlegroups.com...
>>On Mar 25, 11:16 am, "Leon" <[email protected]> wrote:
>>> <[email protected]> wrote in message
>>>
>>> news:7fe1d981-7832-4fe4-82ed-58cb0909f6b0@g10g2000yqh.googlegroups.com...
>>> On Mar 25, 9:00 am, "[email protected]" <[email protected]>
>>>
>>> > When I glue something up in the field that requires this kind of
>>> > clamping, I actually level my "table" on the sawhorses by carefully
>>> > leveling the material I am using for a top.
>>>
>>> > This cuts out most of the problems.
>>>
>>> Level or planar? How level is level? I see vertical glue-up jigs.
>>> How do they work?
>>>
>>> When clamping up water boards the surface absolutely myst be "Level".
>> ????????????
>>
>>What is a "water board"?
>>
>>Don't you watch the news?
>
>Silly me. I thought we were talking about woodworking, for once.
It's sheer torture, isn't it? <giggle>
--
Challenges are gifts that force us to search for a new center of gravity.
Don't fight them. Just find a different way to stand.
-- Oprah Winfrey
"Upscale" <[email protected]> wrote in message
news:[email protected]...
> On Wed, 24 Mar 2010 16:49:21 -0500, Swingman <[email protected]> wrote:
>
>>My Bessey's are close enough not to worry about, and the results have so
>>far been perfect enough. :)
>
> Think I remember reading that the jaw faces aren't completely parallel
> until they're clamped down at which point they do align forming a
> perfectly square clamping surface.
That is correct however that point is at a specific pressure at any given
opening distance. Change the opening distance or pressure and you are over
or under.
<[email protected]> wrote in message
news:ffeb0697-26d2-4e90-a244-5c4ff3f3b53e@k19g2000yqn.googlegroups.com...
On Mar 25, 11:16 am, "Leon" <[email protected]> wrote:
> <[email protected]> wrote in message
>
> news:7fe1d981-7832-4fe4-82ed-58cb0909f6b0@g10g2000yqh.googlegroups.com...
> On Mar 25, 9:00 am, "[email protected]" <[email protected]>
>
> > When I glue something up in the field that requires this kind of
> > clamping, I actually level my "table" on the sawhorses by carefully
> > leveling the material I am using for a top.
>
> > This cuts out most of the problems.
>
> Level or planar? How level is level? I see vertical glue-up jigs.
> How do they work?
>
> When clamping up water boards the surface absolutely myst be "Level".
????????????
What is a "water board"?
Don't you watch the news?