> Has anyone here tried this stuff on cherry? Good results?
I've just recently used it on a bookshelf made from poplar - I was very
happy with the results. It took a few more coats than brushing on poly,
but much easier - no worries about runs, drips, brush marks, etc...
I can't imagine that using it on cherry would be any different.
"RonB" <[email protected]> wrote in message
news:k6GHg.104804$LF4.14883@dukeread05...
>
> "bob" <[email protected]> wrote in message
> news:[email protected]...
> > Has anyone here tried this stuff on cherry? Good results?
> >
> >
> Not on cherry yet. I have used it on top of Minwax stain on Oak, Walnut
and
> Maple with very nice results. I have also applied it to seal up Baltic
> Birch plywood with good results.
>
> It takes longer to build up than brushed poly. If you are used to
brushing
> two coats of poly, plan on about four coats of the wiping poly. Good news
> is that it drys fairly quickly (2-3 hours in low humidity). Otherwise
> pretty much the same process as brush or spray. I usually apply a couple
of
> light coats without sanding and then sand lightly between coats. The
wiping
> pretty well does away with bubble, streak and sag problems; but you still
> have to knock some dust loose.
>
> All experince is with the semi-gloss. However if you want to add slightly
> more gloss on the last coat or two, try not shaking the can and pour
> lightly. It keeps the dulling agent from suspending and (I think) it adds
a
> little gloss.
>
> Good Luck
> RonB
>
>
Thanks. Looking back through usenet archives, there seems to be the
suggestion that it contains oil as well, but there is no mention of this on
the Minwax website. I was planning to oil the cherry first, but if the stuff
already has oil in it, I can skip the step. I'll prolly just buy some and do
a few tests.
--
Bob
Travel and Astronomy Photos
http://www3.sympatico.ca/bomo
Thanks for the replies. What I've ended up using is Deftoil tung-poly
finish, and the results on the cherry are absolutely stunning.
I also did a little ad hoc experiment on the weekend. I applied several
differnet oils (tung, tung-poly, linseed, tung-teak) to a bunch of different
pieces of cherry I'm using for the kitchen island. There was a slab of
cherry veneer 3/4 ply, 1/4 ply, and a couple of solid planks of sapwood and
heartwood. I applied the same set of oils to each board, and left them out
in the sun all day, each one half covered.
The results were quite striking, even for just one day of sunlight. I may
post photos when I get a chance. I knew the bare wood would darken, but was
more curious to see how the oiled parts darkened.
People often don't want to "wait" for cherry, but really, you don't have to
wait long.
--
Bob
Travel and Astronomy Photos
http://www3.sympatico.ca/bomo
"mac davis" <[email protected]> wrote in message
news:[email protected]...
> On Fri, 25 Aug 2006 12:35:35 -0400, "bob" <[email protected]> wrote:
>
> >Has anyone here tried this stuff on cherry? Good results?
>
> I've used it on cherry bowls and liked the result.... more "hand rubbed"
look
> and less like plastic coated..
>
> It darkens the cherry a bit, but most folks like that and season it to
make it
> darker..
> Mac
>
> https://home.comcast.net/~mac.davis
> https://home.comcast.net/~mac.davis/wood_stuff.htm
> Thanks. Looking back through usenet archives, there seems to be the
> suggestion that it contains oil as well, but there is no mention of this
> on
> the Minwax website. I was planning to oil the cherry first, but if the
> stuff
> already has oil in it, I can skip the step. I'll prolly just buy some and
> do
> a few tests.
>
>
Without looking at the can I do believe it contains some Linseed Oil. I
have used quite a bit of danish and tung oil over the years and the wiping
poly applies pretty much the same way. However, you usually don't have to
worry about it drying.
RonB
"bob" <[email protected]> wrote in message
news:[email protected]...
>
> "RonB" <[email protected]> wrote in message
> news:k6GHg.104804$LF4.14883@dukeread05...
>>
>> "bob" <[email protected]> wrote in message
>> news:[email protected]...
>> > Has anyone here tried this stuff on cherry? Good results?
>> >
>> >
>> Not on cherry yet. I have used it on top of Minwax stain on Oak, Walnut
> and
>> Maple with very nice results. I have also applied it to seal up Baltic
>> Birch plywood with good results.
>>
>> It takes longer to build up than brushed poly. If you are used to
> brushing
>> two coats of poly, plan on about four coats of the wiping poly. Good
>> news
>> is that it drys fairly quickly (2-3 hours in low humidity). Otherwise
>> pretty much the same process as brush or spray. I usually apply a couple
> of
>> light coats without sanding and then sand lightly between coats. The
> wiping
>> pretty well does away with bubble, streak and sag problems; but you still
>> have to knock some dust loose.
>>
>> All experince is with the semi-gloss. However if you want to add
>> slightly
>> more gloss on the last coat or two, try not shaking the can and pour
>> lightly. It keeps the dulling agent from suspending and (I think) it
>> adds
> a
>> little gloss.
>>
>> Good Luck
>> RonB
>>
>>
>
> Thanks. Looking back through usenet archives, there seems to be the
> suggestion that it contains oil as well, but there is no mention of this
> on
> the Minwax website. I was planning to oil the cherry first, but if the
> stuff
> already has oil in it, I can skip the step. I'll prolly just buy some and
> do
> a few tests.
>
I have used it many times; works fine.
No oil, just dilute poly with some additives (at least I think it has
additives, since it works better than poly I have diluted myself.)
I often oil the whole piece and then put poly on the top surface.
Use gloss finish. You can then dull it down with fine steelwool if you
want.
"bob" <[email protected]> wrote in message
news:[email protected]...
> Has anyone here tried this stuff on cherry? Good results?
>
>
Not on cherry yet. I have used it on top of Minwax stain on Oak, Walnut and
Maple with very nice results. I have also applied it to seal up Baltic
Birch plywood with good results.
It takes longer to build up than brushed poly. If you are used to brushing
two coats of poly, plan on about four coats of the wiping poly. Good news
is that it drys fairly quickly (2-3 hours in low humidity). Otherwise
pretty much the same process as brush or spray. I usually apply a couple of
light coats without sanding and then sand lightly between coats. The wiping
pretty well does away with bubble, streak and sag problems; but you still
have to knock some dust loose.
All experince is with the semi-gloss. However if you want to add slightly
more gloss on the last coat or two, try not shaking the can and pour
lightly. It keeps the dulling agent from suspending and (I think) it adds a
little gloss.
Good Luck
RonB
On Fri, 25 Aug 2006 12:35:35 -0400, "bob" <[email protected]> wrote:
>Has anyone here tried this stuff on cherry? Good results?
I've used it on cherry bowls and liked the result.... more "hand rubbed" look
and less like plastic coated..
It darkens the cherry a bit, but most folks like that and season it to make it
darker..
Mac
https://home.comcast.net/~mac.davis
https://home.comcast.net/~mac.davis/wood_stuff.htm
"bob" <[email protected]> wrote in message
news:[email protected]...
> Has anyone here tried this stuff on cherry? Good results?
>
>
> --
> Bob
>
YES! I used it on a cherry dining table with excellent results. You can
see it here:
http://www.garagewoodworks.com/Cherry_Table.htm
I finished the finish with 4F pumice.
--
Stoutman
http://www.garagewoodworks.com