The problem is they are not sure if the shop fox 6" jointer head is the generic
one that most of the 6" machines use. I want to find someone to install it so I
don't want to take it apart to get the measurements. I got the measurements of
the end of the head though.
Anyone got x-ray vision with built in measurements??
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
Isn't this the same as a Grizzly? I've been under the impression that
most Shop Fox machines are white versions of Grizzly designs intended
to be sold by retailers instead of direct from Grizzly.
Steve Knight <[email protected]> wrote:
>The problem is they are not sure if the shop fox 6" jointer head is the generic
>one that most of the 6" machines use. I want to find someone to install it so I
>don't want to take it apart to get the measurements. I got the measurements of
>the end of the head though.
> Anyone got x-ray vision with built in measurements??
Can you see the edge (end) of a knife?
The thickness, width and length of the knife are all you need.
Tom
"Steve Knight" <[email protected]> wrote in message
news:[email protected]...
> The problem is they are not sure if the shop fox 6" jointer head is the
generic
> one that most of the 6" machines use. I want to find someone to install it
so I
> don't want to take it apart to get the measurements. I got the
measurements of
> the end of the head though.
> Anyone got x-ray vision with built in measurements??
>
>
> --
> Knight-Toolworks & Custom Planes
> Custom made wooden planes at reasonable prices
> See http://www.knight-toolworks.com For prices and ordering instructions.
On Thu, 3 Feb 2005 06:36:37 -0500, "David F. Eisan"
<[email protected]> wrote:
>Steve,
>
>Have you contacted these people?
>
>http://www.byrdtool.com/
>
oops I forgot to post their link that's who I am getting it from. they are not
positive if the head is the generic one or not. but I hope it is. I ordered it
(a few weeks) and if not when I remove the old one I can measure it.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
On Thu, 3 Feb 2005 05:24:02 -0500, "Thomas Bunetta" <[email protected]> wrote:
>Can you see the edge (end) of a knife?
>The thickness, width and length of the knife are all you need.
>
spiral cutter head. not the carbide knives. I left the link out sorry about
that.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
dOn Thu, 03 Feb 2005 23:29:54 GMT, Larry Kraus <[email protected]> wrote:
>Isn't this the same as a Grizzly? I've been under the impression that
>most Shop Fox machines are white versions of Grizzly designs intended
>to be sold by retailers instead of direct from Grizzly.
that's what I am thinking but not sure. the people at shopfox did not really
give me much of an answer on it. all they were worried about was the void
warranty.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
Steve,
Have you contacted these people?
http://www.byrdtool.com/
Take care,
David.
"Steve Knight" <[email protected]> wrote in message
news:[email protected]...
> The problem is they are not sure if the shop fox 6" jointer head is the
generic
> one that most of the 6" machines use. I want to find someone to install it
so I
> don't want to take it apart to get the measurements. I got the
measurements of
> the end of the head though.
> Anyone got x-ray vision with built in measurements??
>
>
> --
> Knight-Toolworks & Custom Planes
> Custom made wooden planes at reasonable prices
> See http://www.knight-toolworks.com For prices and ordering instructions.