I've found *lots* of sources for *triple* bead cutters similar to this:
http://www.grizzly.com/products/item.cfm?itemnumber=C2095
Anybody know of a source for something like this that will cut four (or more)
beads at a time? I'd prefer a shaper cutter, but router bits will do.
Yes, I know I can make multiple passes. I'll be doing that anyway, as I need
to put at least eight beads (ten would be better) on a board. With a
triple-bead cutter, I'll have to make three passes, including resetting the
cutter height (or adding spacers, or putting the wood on a purpose-build
sled). I figure that, with a four-bead cutter, I could make one pass, flip the
board, and make a second pass, without readjusting anything.
TIA...
--
Regards,
Doug Miller (alphageek at milmac dot com)
Nobody ever left footprints in the sands of time by sitting on his butt.
And who wants to leave buttprints in the sands of time?
In article <45Z5e.258$%[email protected]>, "BobS" <[email protected]> wrote:
>How about a 5-bead cutter from Delta ?
>
>http://store.yahoo.com/ekimco/09-195.html
>Here's a pic of one from:
>http://www.amazon.
com/exec/obidos/ASIN/B00004WHZ7/eneva-20/102-8835499-7146523
>Bob S.
Cool - thanks, Bob. All I came up with when I searched was single- and
triple-bead cutters. Didn't see that one. That'll do pretty well, I think.
Looks a bit scary - I'm accustomed to the safety cutters. Either way, though,
the shaper demands (and gets) respect.
>
>"Doug Miller" <[email protected]> wrote in message
>news:[email protected]...
>> I've found *lots* of sources for *triple* bead cutters similar to this:
>> http://www.grizzly.com/products/item.cfm?itemnumber=C2095
>>
>> Anybody know of a source for something like this that will cut four (or
>more)
>> beads at a time? I'd prefer a shaper cutter, but router bits will do.
>>
>> Yes, I know I can make multiple passes. I'll be doing that anyway, as I
>need
>> to put at least eight beads (ten would be better) on a board. With a
>> triple-bead cutter, I'll have to make three passes, including resetting
>the
>> cutter height (or adding spacers, or putting the wood on a purpose-build
>> sled). I figure that, with a four-bead cutter, I could make one pass, flip
>the
>> board, and make a second pass, without readjusting anything.
>>
>> TIA...
>>
>> --
>> Regards,
>> Doug Miller (alphageek at milmac dot com)
>>
>> Nobody ever left footprints in the sands of time by sitting on his butt.
>> And who wants to leave buttprints in the sands of time?
>
>
--
Regards,
Doug Miller (alphageek at milmac dot com)
Nobody ever left footprints in the sands of time by sitting on his butt.
And who wants to leave buttprints in the sands of time?
How about a 5-bead cutter from Delta ?
http://store.yahoo.com/ekimco/09-195.html
Bob S.
"Doug Miller" <[email protected]> wrote in message
news:[email protected]...
> I've found *lots* of sources for *triple* bead cutters similar to this:
> http://www.grizzly.com/products/item.cfm?itemnumber=C2095
>
> Anybody know of a source for something like this that will cut four (or
more)
> beads at a time? I'd prefer a shaper cutter, but router bits will do.
>
> Yes, I know I can make multiple passes. I'll be doing that anyway, as I
need
> to put at least eight beads (ten would be better) on a board. With a
> triple-bead cutter, I'll have to make three passes, including resetting
the
> cutter height (or adding spacers, or putting the wood on a purpose-build
> sled). I figure that, with a four-bead cutter, I could make one pass, flip
the
> board, and make a second pass, without readjusting anything.
>
> TIA...
>
> --
> Regards,
> Doug Miller (alphageek at milmac dot com)
>
> Nobody ever left footprints in the sands of time by sitting on his butt.
> And who wants to leave buttprints in the sands of time?
Doug Miller wrote:
> I've found *lots* of sources for *triple* bead cutters similar to this:
> http://www.grizzly.com/products/item.cfm?itemnumber=C2095
>
> Anybody know of a source for something like this that will cut four (or more)
> beads at a time? I'd prefer a shaper cutter, but router bits will do.
>
> Yes, I know I can make multiple passes. I'll be doing that anyway, as I need
> to put at least eight beads (ten would be better) on a board. With a
> triple-bead cutter, I'll have to make three passes, including resetting the
> cutter height (or adding spacers, or putting the wood on a purpose-build
> sled). I figure that, with a four-bead cutter, I could make one pass, flip the
> board, and make a second pass, without readjusting anything.
>
> TIA...
>
> --
> Regards,
> Doug Miller (alphageek at milmac dot com)
>
> Nobody ever left footprints in the sands of time by sitting on his butt.
> And who wants to leave buttprints in the sands of time?
Received a pricecutter.com paper catalog today and there on the front
page is a photo of a router bit that will cut five beads. It is a
tenoning bit with wide flanges top and bottom but perhaps you can use it.
mahalo,
jo4hn
Did a little more searching and of course all roads lead to Amazon - who
say - Not Available. But search on the part number - oh hell, here I am
trying to tell you how to search.......;-)
Yer welcome - hope you can find it. Looks like a real finger-getter too.
Bob S.
"Doug Miller" <[email protected]> wrote in message
news:[email protected]...
> In article <45Z5e.258$%[email protected]>, "BobS"
<[email protected]> wrote:
> >How about a 5-bead cutter from Delta ?
> >
> >http://store.yahoo.com/ekimco/09-195.html
> >Here's a pic of one from:
>
> >http://www.amazon.
> com/exec/obidos/ASIN/B00004WHZ7/eneva-20/102-8835499-7146523
>
> >Bob S.
>
> Cool - thanks, Bob. All I came up with when I searched was single- and
> triple-bead cutters. Didn't see that one. That'll do pretty well, I think.
>
> Looks a bit scary - I'm accustomed to the safety cutters. Either way,
though,
> the shaper demands (and gets) respect.
>
> >
> >"Doug Miller" <[email protected]> wrote in message
> >news:[email protected]...
> >> I've found *lots* of sources for *triple* bead cutters similar to this:
> >> http://www.grizzly.com/products/item.cfm?itemnumber=C2095
> >>
> >> Anybody know of a source for something like this that will cut four (or
> >more)
> >> beads at a time? I'd prefer a shaper cutter, but router bits will do.
> >>
> >> Yes, I know I can make multiple passes. I'll be doing that anyway, as I
> >need
> >> to put at least eight beads (ten would be better) on a board. With a
> >> triple-bead cutter, I'll have to make three passes, including resetting
> >the
> >> cutter height (or adding spacers, or putting the wood on a
purpose-build
> >> sled). I figure that, with a four-bead cutter, I could make one pass,
flip
> >the
> >> board, and make a second pass, without readjusting anything.
> >>
> >> TIA...
> >>
> >> --
> >> Regards,
> >> Doug Miller (alphageek at milmac dot com)
> >>
> >> Nobody ever left footprints in the sands of time by sitting on his
butt.
> >> And who wants to leave buttprints in the sands of time?
> >
> >
>
> --
> Regards,
> Doug Miller (alphageek at milmac dot com)
>
> Nobody ever left footprints in the sands of time by sitting on his butt.
> And who wants to leave buttprints in the sands of time?
Here's a pic of one from:
http://www.amazon.com/exec/obidos/ASIN/B00004WHZ7/eneva-20/102-8835499-7146523
Bob S.
"Doug Miller" <[email protected]> wrote in message
news:[email protected]...
> I've found *lots* of sources for *triple* bead cutters similar to this:
> http://www.grizzly.com/products/item.cfm?itemnumber=C2095
>
> Anybody know of a source for something like this that will cut four (or
more)
> beads at a time? I'd prefer a shaper cutter, but router bits will do.
>
> Yes, I know I can make multiple passes. I'll be doing that anyway, as I
need
> to put at least eight beads (ten would be better) on a board. With a
> triple-bead cutter, I'll have to make three passes, including resetting
the
> cutter height (or adding spacers, or putting the wood on a purpose-build
> sled). I figure that, with a four-bead cutter, I could make one pass, flip
the
> board, and make a second pass, without readjusting anything.
>
> TIA...
>
> --
> Regards,
> Doug Miller (alphageek at milmac dot com)
>
> Nobody ever left footprints in the sands of time by sitting on his butt.
> And who wants to leave buttprints in the sands of time?