Howdy,
Some time ago I bought a large Delta table saw on the mistaken
assumption that I could get 3 phase electricity for it at an affordable
price.
I don't know enough about table saws to assess its condition. But
let's assume it's "fair".
What's certain is that it's taking more room than I can afford to give
it. Therefore I'd like to sell it at the highest price that is still a
bargain for the buyer.
If any of y'all would be kind enough to share your knowledge I'll
definitely appreciate it. The saw is in Texas. It's been stored
inside but the table top is rusty. I don't have a model number or any
details but could easily get these.
Even a ballpark "high - low" value would be helpful.
Thanks,
Vernon
Thanks to everybody for your responses.
We live in Brenham, Texas. That's about 75 miles NW of Houston.
VT
R. Pierce Butler wrote:
> [email protected] wrote in news:1150604098.444476.239690
> @r2g2000cwb.googlegroups.com:
>
> > Howdy,
> >
> > Some time ago I bought a large Delta table saw on the mistaken
> > assumption that I could get 3 phase electricity for it at an affordable
> > price.
> >
> > I don't know enough about table saws to assess its condition. But
> > let's assume it's "fair".
> >
> > What's certain is that it's taking more room than I can afford to give
> > it. Therefore I'd like to sell it at the highest price that is still a
> > bargain for the buyer.
> >
> > If any of y'all would be kind enough to share your knowledge I'll
> > definitely appreciate it. The saw is in Texas. It's been stored
> > inside but the table top is rusty. I don't have a model number or any
> > details but could easily get these.
> >
> > Even a ballpark "high - low" value would be helpful.
> >
> > Thanks,
> > Vernon
> >
> >
>
> Where in Texas?
>
> Texas is kinda big.
Todd,
It did cross my mind to swap out the motor. However, the current motor
is not only big but it has some mount brackets welded to it that allow
it to tilt. That would appear to make a conversion to single phase
well beyond my attention span and possibly, ability.
VT
todd wrote:
> <[email protected]> wrote in message
> news:[email protected]...
> > Howdy,
> >
> > Some time ago I bought a large Delta table saw on the mistaken
> > assumption that I could get 3 phase electricity for it at an affordable
> > price.
> >
> > I don't know enough about table saws to assess its condition. But
> > let's assume it's "fair".
> >
> > What's certain is that it's taking more room than I can afford to give
> > it. Therefore I'd like to sell it at the highest price that is still a
> > bargain for the buyer.
> >
> > If any of y'all would be kind enough to share your knowledge I'll
> > definitely appreciate it. The saw is in Texas. It's been stored
> > inside but the table top is rusty. I don't have a model number or any
> > details but could easily get these.
> >
> > Even a ballpark "high - low" value would be helpful.
> >
> > Thanks,
> > Vernon
>
> If you need a table saw, why not swap the motor out with a single-phase
> model? I did it with a Delta jointer.
>
> todd
Pete,
I'm not sure what a VFD is. Is that a phase converter?
V
Pete C. wrote:
> todd wrote:
> >
> > <[email protected]> wrote in message
> > news:[email protected]...
> > > Howdy,
> > >
> > > Some time ago I bought a large Delta table saw on the mistaken
> > > assumption that I could get 3 phase electricity for it at an affordable
> > > price.
> > >
> > > I don't know enough about table saws to assess its condition. But
> > > let's assume it's "fair".
> > >
> > > What's certain is that it's taking more room than I can afford to give
> > > it. Therefore I'd like to sell it at the highest price that is still a
> > > bargain for the buyer.
> > >
> > > If any of y'all would be kind enough to share your knowledge I'll
> > > definitely appreciate it. The saw is in Texas. It's been stored
> > > inside but the table top is rusty. I don't have a model number or any
> > > details but could easily get these.
> > >
> > > Even a ballpark "high - low" value would be helpful.
> > >
> > > Thanks,
> > > Vernon
> >
> > If you need a table saw, why not swap the motor out with a single-phase
> > model? I did it with a Delta jointer.
> >
> > todd
>
> Or put a $200 VFD on the 3ph motor and feed it with 240V 1ph. You'll get
> the added benefits of soft start and variable speed as well which might
> be particularly nice if you use molding heads and want to slow it down a
> bit. Of course if you let it get rusty you've got a bit of a project
> reconditioning it first.
>
> Pete C.
Jim,
In this case, although the motor "just bolts to the saw", it does so by
means of mounts that are welded to the motor frame. Since the angle of
tilt indexes to an indicator, I judge that even if I were to custom fab
the ear tabs and weld 'em to the replacement motor, it would be a
precision alignment/welding job. Although I'm a fair hobbyist welder
it would appear that a single phase conversion would be a significant
undertaking.
I don't remember the HP rating of this motor but it is the size of a
small watermelon. I have a hard time imagining what kind of single
phase motor would be a suitable replacement.
On the other hand, if any of y'all have "been there and done that" I'd
love to hear your tale of glee (or woe).
I'm not a hardcore wood person. But I love quality tools and I'd love
to keep the saw if I can make it do something useful. Let's say
something wild. Like cutting wood!
Finally, to shift gears a minute... How DO you refurbish a rusty table
top?
Vernon
Jim wrote:
> <[email protected]> wrote in message
> news:[email protected]...
> > Todd,
> >
> > It did cross my mind to swap out the motor. However, the current motor
> > is not only big but it has some mount brackets welded to it that allow
> > it to tilt. That would appear to make a conversion to single phase
> > well beyond my attention span and possibly, ability.
> >
> > VT
> > todd wrote:
> >> <[email protected]> wrote in message
> >> news:[email protected]...
> >> > Howdy,
> >> >
> >> > Some time ago I bought a large Delta table saw on the mistaken
> >> > assumption that I could get 3 phase electricity for it at an affordable
> >> > price.
> >> >
> >> > I don't know enough about table saws to assess its condition. But
> >> > let's assume it's "fair".
> >> >
> >> > What's certain is that it's taking more room than I can afford to give
> >> > it. Therefore I'd like to sell it at the highest price that is still a
> >> > bargain for the buyer.
> >> >
> >> > If any of y'all would be kind enough to share your knowledge I'll
> >> > definitely appreciate it. The saw is in Texas. It's been stored
> >> > inside but the table top is rusty. I don't have a model number or any
> >> > details but could easily get these.
> >> >
> >> > Even a ballpark "high - low" value would be helpful.
> >> >
> >> > Thanks,
> >> > Vernon
> >>
> >> If you need a table saw, why not swap the motor out with a single-phase
> >> model? I did it with a Delta jointer.
> >>
> >> todd
> >
> Just buy a single phase motor that has the same horsepower rating. Then you
> would need to get a single phase switch. You buy these things at the same
> place.
>
> The motor just bolts to the saw. Surely you can figure out how to take one
> off and bolt the other one back in the same place.
>
> Jim
Wow!
So somebody has ALREADY re-invented the wheel?
Thanks!
VT
Markem sixoneeight wrote:
> On 18 Jun 2006 09:51:07 -0700, [email protected] wrote:
>
> >In this case, although the motor "just bolts to the saw", it does so by
> >means of mounts that are welded to the motor frame
>
> Replacement motors for the Unisaw are available with the mount already
> attached. 3HP ones are readily availble on ebay for under $300.
>
> Mark
> (sixoneeight) = 618
Frank and everybody,
I had to travel to Mexico City unexpectedly due to the death of a dear
old friend.
Now that I'm back, I want to thank you all for your posts, and
especially for the ebay links to replacement motors.
Since I last posted I took the saw over to our farm. I buttered the
top down with motor oil to retard further rusting.
As a result of your responses I'm much more razzed and upbeat about the
saw. But I'm also aware that I have a lot to learn about it.
Here's the little I know up to now:
It has a 1.5 (one point five) HP 3 phase motor, rated at 1725 rpm.
There is an oval cut-out in the pedestal side that allows the motor to
tilt 45 degrees in either direction without the motor end contacting
the pedestal.
A review of some of the ebay ads for replacement motors has made it
apparent that most replacement motors are rated at over 3,000 RPM.
Some of them are 3 HP or higher.
I also saw a reference to potential problems with some replacement
motors not clearing the pedestal side.
One poster inquired about the fence system. Regrettably, I'm too
ignorant of saws to know the answer. There are some rectangular slots
in the table. The saw has an accessory that fits down into one of
these grooves that has an adjustable protractor like device on it. I
think there is also a rip fence. The reason for my uncertainty is that
I think I have some accessories stored elsewhere. I need to dig these
out and get a clue.
I am remodeling a little house for conversion to a commercial purpose.
This saw would be a valuable addition to my resources.
Therefore, I will genuinely appreciate y'all continuing to kick this
tarbaby with me.
Best regards and many thanks,
Vernon
Frank Boettcher wrote:
> On 17 Jun 2006 21:14:58 -0700, [email protected] wrote:
>
> >Howdy,
> >
> >Some time ago I bought a large Delta table saw on the mistaken
> >assumption that I could get 3 phase electricity for it at an affordable
> >price.
> >
> >I don't know enough about table saws to assess its condition. But
> >let's assume it's "fair".
> >
> >What's certain is that it's taking more room than I can afford to give
> >it. Therefore I'd like to sell it at the highest price that is still a
> >bargain for the buyer.
> >
> >If any of y'all would be kind enough to share your knowledge I'll
> >definitely appreciate it. The saw is in Texas. It's been stored
> >inside but the table top is rusty. I don't have a model number or any
> >details but could easily get these.
> >
> >Even a ballpark "high - low" value would be helpful.
> >
> >Thanks,
> >Vernon
>
>
> What do you mean by "large"? Unisaw (ten inch tilting arbor), or
> larger than that (RT40)? Value is considerably different.
>
> Does it have a fence system? what kind? Impacts the value somewhat?
>
> Before you take any suggestions about replacing the motor, you need to
> have the specific model and if a Unisaw, whether it is a right tilt or
> left tilt. Motors are different. And you may have to buy a motor
> starter if you're LVC is not convertible in a cost effective manner.
> GPE (best choice) or one of the knock offs, will add $ to the motor
> phase conversion.
>
> Frank
Howdy Frank,
Thank you for taking the time to write. Actually, I'm not a complete
rube. I am just not a hard-core woodworker. I actually took a shop
course in college back before they invented electricity.
Your point about "is it a unisaw" was quite interesting. All I know is
it's a Delta and that it's a big old machine. I will strive to take
some pictures in the near future and post 'em to my web page. Then,
hopefully, y'all will be kind enough to help me kick the project along.
Regards,
Vernon
Frank Boettcher wrote:
> On 22 Jun 2006 14:26:48 -0700, [email protected] wrote:
>
> >Frank and everybody,
> >
> >I had to travel to Mexico City unexpectedly due to the death of a dear
> >old friend.
> >
> >Now that I'm back, I want to thank you all for your posts, and
> >especially for the ebay links to replacement motors.
> >
> >Since I last posted I took the saw over to our farm. I buttered the
> >top down with motor oil to retard further rusting.
> >
> >As a result of your responses I'm much more razzed and upbeat about the
> >saw. But I'm also aware that I have a lot to learn about it.
> >
> >Here's the little I know up to now:
> >
> >It has a 1.5 (one point five) HP 3 phase motor, rated at 1725 rpm.
> >There is an oval cut-out in the pedestal side that allows the motor to
> >tilt 45 degrees in either direction without the motor end contacting
> >the pedestal.
> >
> >A review of some of the ebay ads for replacement motors has made it
> >apparent that most replacement motors are rated at over 3,000 RPM.
> >Some of them are 3 HP or higher.
>
> The standard output RPM for a Unisaw is 3450. Has been for many years.
> If your saw is operating with a 1725 ouput then the motor pulley is
> not standard. Or the blade surface speed is wrong. I don't think you
> can find a 1725 single phase motor with Unisaw mount brackets in this
> day and age.
>
> Maybe it is not a Unisaw. You should post links to pictures which
> would be more helpful.
> >
> >I also saw a reference to potential problems with some replacement
> >motors not clearing the pedestal side.
> >
> >One poster inquired about the fence system. Regrettably, I'm too
> >ignorant of saws to know the answer. There are some rectangular slots
> >in the table. The saw has an accessory that fits down into one of
> >these grooves that has an adjustable protractor like device on it. I
> >think there is also a rip fence. The reason for my uncertainty is that
> >I think I have some accessories stored elsewhere. I need to dig these
> >out and get a clue.
>
> If you're actually planning to use the saw when you get it running and
> you know as little as you say, I would suggest you get some basic
> training in the safe and proper use before you strike out in that
> direction.
> >
> >I am remodeling a little house for conversion to a commercial purpose.
> >This saw would be a valuable addition to my resources.
> >
> >Therefore, I will genuinely appreciate y'all continuing to kick this
> >tarbaby with me.
> >
> >Best regards and many thanks,
> >Vernon
> >Frank Boettcher wrote:
> >> On 17 Jun 2006 21:14:58 -0700, [email protected] wrote:
> >>
> >> >Howdy,
> >> >
> >> >Some time ago I bought a large Delta table saw on the mistaken
> >> >assumption that I could get 3 phase electricity for it at an affordable
> >> >price.
> >> >
> >> >I don't know enough about table saws to assess its condition. But
> >> >let's assume it's "fair".
> >> >
> >> >What's certain is that it's taking more room than I can afford to give
> >> >it. Therefore I'd like to sell it at the highest price that is still a
> >> >bargain for the buyer.
> >> >
> >> >If any of y'all would be kind enough to share your knowledge I'll
> >> >definitely appreciate it. The saw is in Texas. It's been stored
> >> >inside but the table top is rusty. I don't have a model number or any
> >> >details but could easily get these.
> >> >
> >> >Even a ballpark "high - low" value would be helpful.
> >> >
> >> >Thanks,
> >> >Vernon
> >>
> >>
> >> What do you mean by "large"? Unisaw (ten inch tilting arbor), or
> >> larger than that (RT40)? Value is considerably different.
> >>
> >> Does it have a fence system? what kind? Impacts the value somewhat?
> >>
> >> Before you take any suggestions about replacing the motor, you need to
> >> have the specific model and if a Unisaw, whether it is a right tilt or
> >> left tilt. Motors are different. And you may have to buy a motor
> >> starter if you're LVC is not convertible in a cost effective manner.
> >> GPE (best choice) or one of the knock offs, will add $ to the motor
> >> phase conversion.
> >>
> >> Frank
On 17 Jun 2006 21:14:58 -0700, [email protected] wrote:
>Howdy,
>
>Some time ago I bought a large Delta table saw on the mistaken
>assumption that I could get 3 phase electricity for it at an affordable
>price.
>
>I don't know enough about table saws to assess its condition. But
>let's assume it's "fair".
>
>What's certain is that it's taking more room than I can afford to give
>it. Therefore I'd like to sell it at the highest price that is still a
>bargain for the buyer.
>
>If any of y'all would be kind enough to share your knowledge I'll
>definitely appreciate it. The saw is in Texas. It's been stored
>inside but the table top is rusty. I don't have a model number or any
>details but could easily get these.
>
>Even a ballpark "high - low" value would be helpful.
Others may disagree, I'd offer $600-650 for a Unisaw in "fair" shape
with a slightly rusty top. A little less if the top is really rusty-
a little more if it is in top running form.
It's worth your while to keep it and fix it up, though. Soon as you
get rid of it, you'll find a use for it.
On 17 Jun 2006 21:14:58 -0700, [email protected] wrote:
>Howdy,
>
>Some time ago I bought a large Delta table saw on the mistaken
>assumption that I could get 3 phase electricity for it at an affordable
>price.
>
>I don't know enough about table saws to assess its condition. But
>let's assume it's "fair".
>
>What's certain is that it's taking more room than I can afford to give
>it. Therefore I'd like to sell it at the highest price that is still a
>bargain for the buyer.
>
>If any of y'all would be kind enough to share your knowledge I'll
>definitely appreciate it. The saw is in Texas. It's been stored
>inside but the table top is rusty. I don't have a model number or any
>details but could easily get these.
>
>Even a ballpark "high - low" value would be helpful.
>
>Thanks,
>Vernon
What do you mean by "large"? Unisaw (ten inch tilting arbor), or
larger than that (RT40)? Value is considerably different.
Does it have a fence system? what kind? Impacts the value somewhat?
Before you take any suggestions about replacing the motor, you need to
have the specific model and if a Unisaw, whether it is a right tilt or
left tilt. Motors are different. And you may have to buy a motor
starter if you're LVC is not convertible in a cost effective manner.
GPE (best choice) or one of the knock offs, will add $ to the motor
phase conversion.
Frank
On 18 Jun 2006 09:51:07 -0700, [email protected] wrote:
>In this case, although the motor "just bolts to the saw", it does so by
>means of mounts that are welded to the motor frame
Replacement motors for the Unisaw are available with the mount already
attached. 3HP ones are readily availble on ebay for under $300.
Mark
(sixoneeight) = 618
todd wrote:
>
> <[email protected]> wrote in message
> news:[email protected]...
> > Howdy,
> >
> > Some time ago I bought a large Delta table saw on the mistaken
> > assumption that I could get 3 phase electricity for it at an affordable
> > price.
> >
> > I don't know enough about table saws to assess its condition. But
> > let's assume it's "fair".
> >
> > What's certain is that it's taking more room than I can afford to give
> > it. Therefore I'd like to sell it at the highest price that is still a
> > bargain for the buyer.
> >
> > If any of y'all would be kind enough to share your knowledge I'll
> > definitely appreciate it. The saw is in Texas. It's been stored
> > inside but the table top is rusty. I don't have a model number or any
> > details but could easily get these.
> >
> > Even a ballpark "high - low" value would be helpful.
> >
> > Thanks,
> > Vernon
>
> If you need a table saw, why not swap the motor out with a single-phase
> model? I did it with a Delta jointer.
>
> todd
Or put a $200 VFD on the 3ph motor and feed it with 240V 1ph. You'll get
the added benefits of soft start and variable speed as well which might
be particularly nice if you use molding heads and want to slow it down a
bit. Of course if you let it get rusty you've got a bit of a project
reconditioning it first.
Pete C.
When I replaced the 3-phase motor in my jointer with a single phase, it cost
me about $140. Since that was the only 3-phase equipment I had, it made
sense for me to just swap the motor. For your case, I'd take the $300 and
put it toward a rotary phase converter.
todd
<[email protected]> wrote in message
news:[email protected]...
> Wow!
>
> So somebody has ALREADY re-invented the wheel?
>
> Thanks!
>
> VT
>
> Markem sixoneeight wrote:
>> On 18 Jun 2006 09:51:07 -0700, [email protected] wrote:
>>
>> >In this case, although the motor "just bolts to the saw", it does so by
>> >means of mounts that are welded to the motor frame
>>
>> Replacement motors for the Unisaw are available with the mount already
>> attached. 3HP ones are readily availble on ebay for under $300.
>>
>> Mark
>> (sixoneeight) = 618
>
For comparison I bought a 30 year old Powermatic Model 66 two years ago
in fair condition. Somewhat rusty table with definite signs of use.
Original cast iron fence, no miter gauge, but it included the original
motor cover and a 3 ph 3 HP motor. Cleaned it up, replaced the triple
belts with power twist link belts and built my own rotary converter. I
paid $240 for the saw. I did have to pick it up and move it myself.
[email protected] wrote:
> Howdy,
>
> Some time ago I bought a large Delta table saw on the mistaken
> assumption that I could get 3 phase electricity for it at an affordable
> price.
>
> I don't know enough about table saws to assess its condition. But
> let's assume it's "fair".
>
> What's certain is that it's taking more room than I can afford to give
> it. Therefore I'd like to sell it at the highest price that is still a
> bargain for the buyer.
>
> If any of y'all would be kind enough to share your knowledge I'll
> definitely appreciate it. The saw is in Texas. It's been stored
> inside but the table top is rusty. I don't have a model number or any
> details but could easily get these.
>
> Even a ballpark "high - low" value would be helpful.
>
> Thanks,
> Vernon
>
<[email protected]> wrote in message
news:[email protected]...
> Howdy,
>
> Some time ago I bought a large Delta table saw on the mistaken
> assumption that I could get 3 phase electricity for it at an affordable
> price.
>
> I don't know enough about table saws to assess its condition. But
> let's assume it's "fair".
>
> What's certain is that it's taking more room than I can afford to give
> it. Therefore I'd like to sell it at the highest price that is still a
> bargain for the buyer.
>
> If any of y'all would be kind enough to share your knowledge I'll
> definitely appreciate it. The saw is in Texas. It's been stored
> inside but the table top is rusty. I don't have a model number or any
> details but could easily get these.
>
> Even a ballpark "high - low" value would be helpful.
>
> Thanks,
> Vernon
If you need a table saw, why not swap the motor out with a single-phase
model? I did it with a Delta jointer.
todd
<[email protected]> wrote in message
news:[email protected]...
> Todd,
>
> It did cross my mind to swap out the motor. However, the current motor
> is not only big but it has some mount brackets welded to it that allow
> it to tilt. That would appear to make a conversion to single phase
> well beyond my attention span and possibly, ability.
>
> VT
> todd wrote:
>> <[email protected]> wrote in message
>> news:[email protected]...
>> > Howdy,
>> >
>> > Some time ago I bought a large Delta table saw on the mistaken
>> > assumption that I could get 3 phase electricity for it at an affordable
>> > price.
>> >
>> > I don't know enough about table saws to assess its condition. But
>> > let's assume it's "fair".
>> >
>> > What's certain is that it's taking more room than I can afford to give
>> > it. Therefore I'd like to sell it at the highest price that is still a
>> > bargain for the buyer.
>> >
>> > If any of y'all would be kind enough to share your knowledge I'll
>> > definitely appreciate it. The saw is in Texas. It's been stored
>> > inside but the table top is rusty. I don't have a model number or any
>> > details but could easily get these.
>> >
>> > Even a ballpark "high - low" value would be helpful.
>> >
>> > Thanks,
>> > Vernon
>>
>> If you need a table saw, why not swap the motor out with a single-phase
>> model? I did it with a Delta jointer.
>>
>> todd
>
Just buy a single phase motor that has the same horsepower rating. Then you
would need to get a single phase switch. You buy these things at the same
place.
The motor just bolts to the saw. Surely you can figure out how to take one
off and bolt the other one back in the same place.
Jim
[email protected] wrote in news:1150604098.444476.239690
@r2g2000cwb.googlegroups.com:
> Howdy,
>
> Some time ago I bought a large Delta table saw on the mistaken
> assumption that I could get 3 phase electricity for it at an affordable
> price.
>
> I don't know enough about table saws to assess its condition. But
> let's assume it's "fair".
>
> What's certain is that it's taking more room than I can afford to give
> it. Therefore I'd like to sell it at the highest price that is still a
> bargain for the buyer.
>
> If any of y'all would be kind enough to share your knowledge I'll
> definitely appreciate it. The saw is in Texas. It's been stored
> inside but the table top is rusty. I don't have a model number or any
> details but could easily get these.
>
> Even a ballpark "high - low" value would be helpful.
>
> Thanks,
> Vernon
>
>
Where in Texas?
Texas is kinda big.
<[email protected]> wrote in message
news:[email protected]...
> Thanks to everybody for your responses.
>
> We live in Brenham, Texas. That's about 75 miles NW of Houston.
Hmmm . . . I kept my three-phase when I upgraded the electrical at
my house . Uh, how much you say?
--
"New Wave" Dave In Houston
Since we do not know the model, it's pretty hard to
know "exactly" what you have...
This will fix your problem on "OLDER" Unisaws.
http://cgi.ebay.com/1-5-HP-Delta-Replacement-Unisaw-Motor-Leeson_W0QQitemZ7631270852QQihZ017QQcategoryZ20789QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
If this is a newer saw, you will need a 3HP, from the same folks....
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=7631269549&ssPageName=MERC_VI_RSCC_Pr4_PcY_BIN_Stores_IT
[email protected] wrote:
> Howdy,
>
> Some time ago I bought a large Delta table saw on the mistaken
> assumption that I could get 3 phase electricity for it at an affordable
> price.
On 22 Jun 2006 14:26:48 -0700, [email protected] wrote:
>Frank and everybody,
>
>I had to travel to Mexico City unexpectedly due to the death of a dear
>old friend.
>
>Now that I'm back, I want to thank you all for your posts, and
>especially for the ebay links to replacement motors.
>
>Since I last posted I took the saw over to our farm. I buttered the
>top down with motor oil to retard further rusting.
>
>As a result of your responses I'm much more razzed and upbeat about the
>saw. But I'm also aware that I have a lot to learn about it.
>
>Here's the little I know up to now:
>
>It has a 1.5 (one point five) HP 3 phase motor, rated at 1725 rpm.
>There is an oval cut-out in the pedestal side that allows the motor to
>tilt 45 degrees in either direction without the motor end contacting
>the pedestal.
>
>A review of some of the ebay ads for replacement motors has made it
>apparent that most replacement motors are rated at over 3,000 RPM.
>Some of them are 3 HP or higher.
The standard output RPM for a Unisaw is 3450. Has been for many years.
If your saw is operating with a 1725 ouput then the motor pulley is
not standard. Or the blade surface speed is wrong. I don't think you
can find a 1725 single phase motor with Unisaw mount brackets in this
day and age.
Maybe it is not a Unisaw. You should post links to pictures which
would be more helpful.
>
>I also saw a reference to potential problems with some replacement
>motors not clearing the pedestal side.
>
>One poster inquired about the fence system. Regrettably, I'm too
>ignorant of saws to know the answer. There are some rectangular slots
>in the table. The saw has an accessory that fits down into one of
>these grooves that has an adjustable protractor like device on it. I
>think there is also a rip fence. The reason for my uncertainty is that
>I think I have some accessories stored elsewhere. I need to dig these
>out and get a clue.
If you're actually planning to use the saw when you get it running and
you know as little as you say, I would suggest you get some basic
training in the safe and proper use before you strike out in that
direction.
>
>I am remodeling a little house for conversion to a commercial purpose.
>This saw would be a valuable addition to my resources.
>
>Therefore, I will genuinely appreciate y'all continuing to kick this
>tarbaby with me.
>
>Best regards and many thanks,
>Vernon
>Frank Boettcher wrote:
>> On 17 Jun 2006 21:14:58 -0700, [email protected] wrote:
>>
>> >Howdy,
>> >
>> >Some time ago I bought a large Delta table saw on the mistaken
>> >assumption that I could get 3 phase electricity for it at an affordable
>> >price.
>> >
>> >I don't know enough about table saws to assess its condition. But
>> >let's assume it's "fair".
>> >
>> >What's certain is that it's taking more room than I can afford to give
>> >it. Therefore I'd like to sell it at the highest price that is still a
>> >bargain for the buyer.
>> >
>> >If any of y'all would be kind enough to share your knowledge I'll
>> >definitely appreciate it. The saw is in Texas. It's been stored
>> >inside but the table top is rusty. I don't have a model number or any
>> >details but could easily get these.
>> >
>> >Even a ballpark "high - low" value would be helpful.
>> >
>> >Thanks,
>> >Vernon
>>
>>
>> What do you mean by "large"? Unisaw (ten inch tilting arbor), or
>> larger than that (RT40)? Value is considerably different.
>>
>> Does it have a fence system? what kind? Impacts the value somewhat?
>>
>> Before you take any suggestions about replacing the motor, you need to
>> have the specific model and if a Unisaw, whether it is a right tilt or
>> left tilt. Motors are different. And you may have to buy a motor
>> starter if you're LVC is not convertible in a cost effective manner.
>> GPE (best choice) or one of the knock offs, will add $ to the motor
>> phase conversion.
>>
>> Frank