There is another dremel question floating around, but I don't believe it
addresses my question. I use my Dremel to sand tight corners in wood
projects. But the behavior of the Dremel concerns me. When I use it, put
it on 'high' and sand away the stairsteps that the jigsaw leaves in tight
corners, I notice that after removing the Dremel from the surface of the
wood that it begins to speed up alarmingly - running extremely fast and
accelerating. In a situation like this I'll switch it to low speed and wait
for it to drop down. But even on 'low' it will rev up after removing it
from the work piece. Is this normal behavior, is the Dremel speeding up to
cool itself down (I notice vanes in the body of it attached to the motor),
or is this some condition that indicates a problem with the Dremel. I don't
believe myself to be pressing down on the dremel attachment too much - after
all I'm sanding wood not grinding rusty steel.
Eigenvector wrote:
> There is another dremel question floating around, but I don't believe
> it addresses my question. I use my Dremel to sand tight corners in
> wood projects. But the behavior of the Dremel concerns me. When I
> use it, put it on 'high' and sand away the stairsteps that the jigsaw
> leaves in tight corners, I notice that after removing the Dremel from
> the surface of the wood that it begins to speed up alarmingly -
> running extremely fast and accelerating. In a situation like this
> I'll switch it to low speed and wait for it to drop down. But even
> on 'low' it will rev up after removing it from the work piece. Is
> this normal behavior, is the Dremel speeding up to cool itself down
> (I notice vanes in the body of it attached to the motor), or is this
> some condition that indicates a problem with the Dremel. I don't
> believe myself to be pressing down on the dremel attachment too much
> - after all I'm sanding wood not grinding rusty steel.
Normal. Back off on the pressure you apply and let the tool do the work.
"HeyBub" <[email protected]> wrote in message
news:[email protected]...
> Eigenvector wrote:
>> There is another dremel question floating around, but I don't believe
>> it addresses my question. I use my Dremel to sand tight corners in
>> wood projects. But the behavior of the Dremel concerns me. When I
>> use it, put it on 'high' and sand away the stairsteps that the jigsaw
>> leaves in tight corners, I notice that after removing the Dremel from
>> the surface of the wood that it begins to speed up alarmingly -
>> running extremely fast and accelerating. In a situation like this
>> I'll switch it to low speed and wait for it to drop down. But even
>> on 'low' it will rev up after removing it from the work piece. Is
>> this normal behavior, is the Dremel speeding up to cool itself down
>> (I notice vanes in the body of it attached to the motor), or is this
>> some condition that indicates a problem with the Dremel. I don't
>> believe myself to be pressing down on the dremel attachment too much
>> - after all I'm sanding wood not grinding rusty steel.
>
> Normal. Back off on the pressure you apply and let the tool do the work.
So the shaft of the attachment isn't supposed to bend in a tight arc from
all the pressure I'm exerting on it? Just kidding, fair enough I'll ease up
on the pressure some more.
"Eigenvector" <[email protected]> wrote in
news:[email protected]:
>
> "HeyBub" <[email protected]> wrote in message
> news:[email protected]...
>> Normal. Back off on the pressure you apply and let the tool do the
>> work.
>
> So the shaft of the attachment isn't supposed to bend in a tight arc
> from all the pressure I'm exerting on it? Just kidding, fair enough
> I'll ease up on the pressure some more.
>
>
>
Also, listen to the tool when you apply it to the work. Does it slow
down when it's pressed to the work? That's normal (but too much is not
letting the tool work, of course).
Puckdropper
--
Wise is the man who attempts to answer his question before asking it.
To email me directly, send a message to puckdropper (at) fastmail.fm