Hello,
In an effort to further my woodworking skills, I started building a small
bathroom vanity. So far, I've only built the carcase and face frame. They're
made from salvaged plywood (11 ply - not sure about the veneer) that was
used as a packing crate and poplar. I plan on using poplar for the door
frame with a luan panel. Nothing fancy here, more of a learning project.
Since the plywood wasn't completely blemish free, my plan was to paint the
vanity. I also tried to use the better portions of it on the outside where
it will show, in order to minimize any blemishes from telegraphing through.
It's often been stated that poplar "takes paint very well". However, after
numerous searches, I haven't been able to find out what primer and paint
should be used. Does anyone here have any suggestions or the proper search
terms to use?
I'm also going to try to post a couple of pictures on a.b.p.w. for feedback.
Thanks in advance to those who post a reply.
Peter.
Peter Bogiatzidis wrote:
>
> It's often been stated that poplar "takes paint very well". However, after
> numerous searches, I haven't been able to find out what primer and paint
> should be used.
I'd use a good, sandable primer/sealer, like BIN. I prefer
non-waterbased primers, as they can be sanded sooner (and better) and
don't raise the grain. Zinnser Sealcoat also works as a good primer,
except it's non-pigmented and clear.
In fact, Sealcoat is one product that nearly every woodworker should
keep on hand, as it will go over or under nearly anything.
If you're buying your materials from a good local paint store, they also
will suggest a good primer.
Hey Peter,
I had a look at your photos...
looks great to me!
My hubby and I made a very similar project for a guest bath last year, out
of the same type of materials.
Since our theme in there is pretty dramatic I opted to go with black.
Rather than prime it I carefully filled and sanded any blemishes on it then
used a black semi-gloss spray that I bought at Lowes.
Personally I don't think you need any primer but you will want to sand
lightly after the first and second coats.
The guys in here helped me out a lot on another painted wood project some
time ago. You don't have to prime the wood, it will take the paint very
well. Unless you're concerned about the wood bleeding through the color,
then I don't know what to say.
Be sure to paint it when it's not too hot and take care to maintain a wet
edge between strokes. A spray will not leave brush lines but will lessen
your color choices. The great thing about a spray semi-gloss is that it is
VERY forgiving.
The results are beautiful and very durable..
I'll post a photo for you on the other group and you can see for yourself.
Kate
"Peter Bogiatzidis" <[email protected]> wrote in message
news:AT3Qj.21422$%[email protected]...
Hello,
In an effort to further my woodworking skills, I started building a small
bathroom vanity. So far, I've only built the carcase and face frame. They're
made from salvaged plywood (11 ply - not sure about the veneer) that was
used as a packing crate and poplar. I plan on using poplar for the door
frame with a luan panel. Nothing fancy here, more of a learning project.
Since the plywood wasn't completely blemish free, my plan was to paint the
vanity. I also tried to use the better portions of it on the outside where
it will show, in order to minimize any blemishes from telegraphing through.
It's often been stated that poplar "takes paint very well". However, after
numerous searches, I haven't been able to find out what primer and paint
should be used. Does anyone here have any suggestions or the proper search
terms to use?
I'm also going to try to post a couple of pictures on a.b.p.w. for feedback.
Thanks in advance to those who post a reply.
Peter.
"Peter Bogiatzidis" <[email protected]> wrote in message
news:AT3Qj.21422$%[email protected]...
> Hello,
>
> In an effort to further my woodworking skills, I started building a small
> bathroom vanity. So far, I've only built the carcase and face frame.
> They're made from salvaged plywood (11 ply - not sure about the veneer)
> that was used as a packing crate and poplar. I plan on using poplar for
> the door frame with a luan panel. Nothing fancy here, more of a learning
> project.
>
> Since the plywood wasn't completely blemish free, my plan was to paint the
> vanity. I also tried to use the better portions of it on the outside where
> it will show, in order to minimize any blemishes from telegraphing
> through.
>
> It's often been stated that poplar "takes paint very well". However, after
> numerous searches, I haven't been able to find out what primer and paint
> should be used. Does anyone here have any suggestions or the proper search
> terms to use?
>
> I'm also going to try to post a couple of pictures on a.b.p.w. for
> feedback.
>
> Thanks in advance to those who post a reply.
>
> Peter.
>
Any good quality paint will work well HOWEVER in a humid bathroom condition
I highly recommend an OIL based paint. It will not become/feel soft and
sticky when the room is humid.
Peter Bogiatzidis wrote:
...
> It's often been stated that poplar "takes paint very well". However, after
> numerous searches, I haven't been able to find out what primer and paint
> should be used. Does anyone here have any suggestions or the proper search
> terms to use?
...
Any good quality interior paint approved/recommended by the manufacturer
ed for new wood is fine. Finish you want is your choice, but normally a
vanity would get fair amount of use of a gloss, washable enamel for the
finish coat would probably be the ticket.
--
dpb wrote:
> Peter Bogiatzidis wrote:
> ...
>> It's often been stated that poplar "takes paint very well". However,
>> after numerous searches, I haven't been able to find out what primer and
>> paint should be used. Does anyone here have any suggestions or the proper
>> search terms to use?
> ...
>
> Any good quality interior paint approved/recommended by the manufacturer
> ed for new wood is fine. Finish you want is your choice, but normally a
> vanity would get fair amount of use of a gloss, washable enamel for the
> finish coat would probably be the ticket.
>
> --
I would coat it with a primer/sealer and fill in any voids.
--
"You can lead them to LINUX
but you can't make them THINK"
Running Mandriva release 2008.0 free-i586 using KDE on i586