ssesOn May 30, 10:32=A0am, [email protected] wrote:
> Hi,
>
> I'm an amature hobbyist. =A0I just picked up a Sears Long Bed Wood
> Lathe, Model Number 28955 and six chisels off of Kijiji. =A0I have been
> searching the net for information and manuals on the lathe but with no
> success. =A0Does anyone have any information they can share with me?
>
> Thanks,
> Sheldon
The number that you found (28955) is more similar to those found on
Atlas metalworking lathes: http://www.lathes.co.uk/craftsman/page3.html
Atlas also supplied Sears with lathes using a prefix =93101=94 in the
model number.
I can=92t say for sure who made your lathe but, Atlas made both
metalworking as well as woodworking equipment: http://www.atlas-press.com/i=
ndex.htm
(Maybe you know, but =93Sheldon=94 is also a brand of lathes:
http://www.lathes.co.uk/sheldon/index.html ) <g>
-DG
<[email protected]> wrote in message
news:[email protected]...
> Hi,
>
> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
> searching the net for information and manuals on the lathe but with no
> success. Does anyone have any information they can share with me?
>
> Thanks,
> Sheldon
Try posting to rec.crafts.woodturning. Odds are that somebody over there
owns or once owned one.
Maybe I should post a bit more detail. It has a capacity to turn a
12" diameter and 41" between centers. It has tubes that the tail
stock moves on. I'm guessing it was made by someone else for Sears.
On Sat, 30 May 2009 17:38:30 GMT, [email protected] wrote:
>Hi Len,
>
>I believe this pre-dates Craftsman. It doesn't have the Craftsman
>label. It only has the old Sears label. The only model number on it
>is 28955.
>
>Thanks.
>
>On Sat, 30 May 2009 12:13:30 -0500, "Len" <[email protected]>
>wrote:
>
>>
>><[email protected]> wrote in message
>>news:[email protected]...
>>> Hi,
>>>
>>> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
>>> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
>>> searching the net for information and manuals on the lathe but with no
>>> success. Does anyone have any information they can share with me?
>>>
>>> Thanks,
>>> Sheldon
>>
>>Is this a 'Craftsman' lathe? If so, what's the full (8 - 10 digits)
>>model number? There should be a plate or sticker somewhere with that
>>info.
>>
>>Len
>>
On 5/30/2009 11:07 AM Nova spake thus:
> [email protected] wrote:
>
>> I believe this pre-dates Craftsman. It doesn't have the Craftsman
>> label. It only has the old Sears label. The only model number on it
>> is 28955.
>
> You might find something over the "Old Woodworking Machines" web site at:
>
> http://www.owwm.com/
I was going to suggest that too, but unfortunately they seem to have
nothing on machines made by Sears, Roebuck and Co., at least none that I
could find. Anyone else have better luck? Maybe your lathe is listed
under the actual manufacturer, if you can determine who that was.
--
Found--the gene that causes belief in genetic determinism
On 5/31/2009 7:38 AM [email protected] spake thus:
> I googled "beginning lathe turning" and got lots of results:
>
> #
> Wood turning lathe tips:techniques: woodturning instruction
> It is our hope that this web site will help both beginning and
> advanced turners to increase their skills in wood turning, tool
> sharpening, and lathe use ...
> aroundthewoods.com/ - 16k - Cached - Similar pages -
> Make your own
> Contents
> Beginners
> Tips
>
> Free Video
> Intermediate to Advanced
> Woodturning lathe maintenance
> Gallery
> More results from aroundthewoods.com »
> #
> Shopsmith - Articles and Projects - Lathe Turning Tips
> Practice, sharp tools, and a reliable machine - these are the surest
> avenues to beautiful lathe turning results. And here are several tips,
> hints, ...
> drillpresstips.com/ownersite/proj_articles/lathetips.htm - 22k -
> Cached - Similar pages -
> #
> Wood Turning - Beginning by Choosing a Lathe - Seven Points to ...
> Wood Turning - Beginning by Choosing a Lathe - Seven Points to
> Consider.
> ezinearticles.com/?Wood-Turning---Beginning-by-Choosing-a-Lathe---
> Seven-Points-to-Consider&id=542794 - 50k - Cached - Similar pages -
So how, exactly, is that mish-mosh of results supposed to help the OP?
So much for the usual lame-brain "just Google it" advice.
--
Found--the gene that causes belief in genetic determinism
On 6/1/2009 1:20 PM [email protected] spake thus:
>> So how, exactly, is that mish-mosh of results supposed to help the OP?
>
> That "mish mosh" was simply an example of what the OP could easily
> have found to answer his question in the first place.
Could have easily answered *nothing*. There wasn't one single link in
that bunch that addressed his lather (a Sears).
> Its one thing to bring a serious query to the group after researching
> and finding a dearth of information or conflicting information and
> quite another to use an OP here to substitute for a little personal
> effort and responsibility.
Maybe.
A couple of people suggested the Old Woodworking Machines (OWWM) site.
While it is an interesting and useful site, it has ABSOLUTELY NO
information on his specific make of lathe (I searched it), so even that
was not very good advice.
Like I've told others here: if you can't help someone, then it's best to
just STFU.
--
Found--the gene that causes belief in genetic determinism
On May 30, 10:32=A0am, [email protected] wrote:
> Hi,
> Sheldon
I googled "beginning lathe turning" and got lots of results:
#
Wood turning lathe tips:techniques: woodturning instruction
It is our hope that this web site will help both beginning and
advanced turners to increase their skills in wood turning, tool
sharpening, and lathe use ...
aroundthewoods.com/ - 16k - Cached - Similar pages -
Make your own
Contents
Beginners
Tips
Free Video
Intermediate to Advanced
Woodturning lathe maintenance
Gallery
More results from aroundthewoods.com =BB
#
Shopsmith - Articles and Projects - Lathe Turning Tips
Practice, sharp tools, and a reliable machine - these are the surest
avenues to beautiful lathe turning results. And here are several tips,
hints, ...
drillpresstips.com/ownersite/proj_articles/lathetips.htm - 22k -
Cached - Similar pages -
#
Wood Turning - Beginning by Choosing a Lathe - Seven Points to ...
Wood Turning - Beginning by Choosing a Lathe - Seven Points to
Consider.
ezinearticles.com/?Wood-Turning---Beginning-by-Choosing-a-Lathe---
Seven-Points-to-Consider&id=3D542794 - 50k - Cached - Similar pages -
Hi Len,
I believe this pre-dates Craftsman. It doesn't have the Craftsman
label. It only has the old Sears label. The only model number on it
is 28955.
Thanks.
On Sat, 30 May 2009 12:13:30 -0500, "Len" <[email protected]>
wrote:
>
><[email protected]> wrote in message
>news:[email protected]...
>> Hi,
>>
>> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
>> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
>> searching the net for information and manuals on the lathe but with no
>> success. Does anyone have any information they can share with me?
>>
>> Thanks,
>> Sheldon
>
>Is this a 'Craftsman' lathe? If so, what's the full (8 - 10 digits)
>model number? There should be a plate or sticker somewhere with that
>info.
>
>Len
>
<[email protected]> wrote in message
news:[email protected]...
> Hi Len,
>
> I believe this pre-dates Craftsman. It doesn't have the Craftsman
> label. It only has the old Sears label. The only model number on it
> is 28955.
>
> Thanks.
>
If it's that old, I suspect it may have actually been made by Emerson
for Sears.
Emerson now makes the 'Rigid' line for Home Depot, so you might want to
take a look at the manual for the Rigid Model 14773 lathe to see if it's
close enough. Click on the "book" just about the picture at
http://www.ridgid.com/Tools/WL1200-Wood-Lathe/ to access the owners
manual.
If that's not it, try looking for a Emerson lathe manual instead of
Sears.
Len
"LD" <[email protected]> wrote in message
news:[email protected]...
> <[email protected]> wrote in message
> news:[email protected]...
>> Hi,
>>
>> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
>> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
>> searching the net for information and manuals on the lathe but with no
>> success. Does anyone have any information they can share with me?
>>
>> Thanks,
>> Sheldon
>
>
> Try posting to rec.crafts.woodturning. Odds are that somebody over there
> owns or once owned one.
Try looking here:
http://www.owwm.com/
Thanks to everyone who has responded. I have checked all the
suggested sites. I haven't found anything that has matched.
I emailed Sears directly to see if they had any information. After
half a dozen frustrating emails the closest they could find in their
database was 101.28950 where I was looking for 28955. Their model
number was for a 12" Craftsman Metal lathe made by Clausing Corp
Services. It seems that they are now Atlas.
The writing on the lathe is both in English and French. Would that
make a difference as to who made it?
On Sat, 30 May 2009 23:04:02 -0700 (PDT), [email protected] wrote:
>ssesOn May 30, 10:32 am, [email protected] wrote:
>> Hi,
>>
>> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
>> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
>> searching the net for information and manuals on the lathe but with no
>> success. Does anyone have any information they can share with me?
>>
>> Thanks,
>> Sheldon
>
>The number that you found (28955) is more similar to those found on
>Atlas metalworking lathes: http://www.lathes.co.uk/craftsman/page3.html
>Atlas also supplied Sears with lathes using a prefix 101 in the
>model number.
>I cant say for sure who made your lathe but, Atlas made both
>metalworking as well as woodworking equipment: http://www.atlas-press.com/index.htm
>
>(Maybe you know, but Sheldon is also a brand of lathes:
>http://www.lathes.co.uk/sheldon/index.html ) <g>
>-DG
In article <[email protected]>,
[email protected] says...
> Thanks to everyone who has responded. I have checked all the
> suggested sites. I haven't found anything that has matched.
>
> I emailed Sears directly to see if they had any information. After
> half a dozen frustrating emails the closest they could find in their
> database was 101.28950 where I was looking for 28955. Their model
> number was for a 12" Craftsman Metal lathe made by Clausing Corp
> Services. It seems that they are now Atlas.
>
> The writing on the lathe is both in English and French. Would that
> make a difference as to who made it?
Is it Canadian manufacture or just marketed in Canada?
Either way, there may be a different numbering system for Canada.
Why not post a picture of the unit along with all the identifying marks
somewhere and ask people to have a look.
Antique Atlas owners could probably tell you whether your craftsman was
in that lineage.
You may find some of them at
http://groups.yahoo.com/group/atlas_craftsman/
In article <[email protected]>, phorbin1
@yahoo.com says...
> In article <[email protected]>,
> [email protected] says...
> > Thanks to everyone who has responded. I have checked all the
> > suggested sites. I haven't found anything that has matched.
> >
> > I emailed Sears directly to see if they had any information. After
> > half a dozen frustrating emails the closest they could find in their
> > database was 101.28950 where I was looking for 28955. Their model
> > number was for a 12" Craftsman Metal lathe made by Clausing Corp
> > Services. It seems that they are now Atlas.
> >
> > The writing on the lathe is both in English and French. Would that
> > make a difference as to who made it?
>
> Is it Canadian manufacture or just marketed in Canada?
>
> Either way, there may be a different numbering system for Canada.
>
> Why not post a picture of the unit along with all the identifying marks
> somewhere and ask people to have a look.
>
> Antique Atlas owners could probably tell you whether your craftsman was
> in that lineage.
>
> You may find some of them at
> http://groups.yahoo.com/group/atlas_craftsman/
Whoops... I think you said before craftsman... Are you sure?
The Craftsman brand goes back to 1927.
"David Nebenzahl" <[email protected]> wrote in message
news:[email protected]...
> On 6/1/2009 1:20 PM [email protected] spake thus:
>
>>> So how, exactly, is that mish-mosh of results supposed to help the OP?
>>
>> That "mish mosh" was simply an example of what the OP could easily
>> have found to answer his question in the first place.
>
> Could have easily answered *nothing*. There wasn't one single link in that
> bunch that addressed his lather (a Sears).
>
>> Its one thing to bring a serious query to the group after researching
>> and finding a dearth of information or conflicting information and
>> quite another to use an OP here to substitute for a little personal
>> effort and responsibility.
>
> Maybe.
>
> A couple of people suggested the Old Woodworking Machines (OWWM) site.
> While it is an interesting and useful site, it has ABSOLUTELY NO
> information on his specific make of lathe (I searched it), so even that
> was not very good advice.
>
> Like I've told others here: if you can't help someone, then it's best to
> just STFU.
>
>
> --
> Found--the gene that causes belief in genetic determinism
I'm disinclined to favor "dittos" but..........ditto.
Max
"Max" <[email protected]> wrote in message
news:[email protected]...
>
>
> , [email protected] wrote:
>>>> >> Hi,
>>>>
>>>> >> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
>>>> >> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
>>>> >> searching the net for information and manuals on the lathe but with
>>>> >> no
>>>> >> success. Does anyone have any information they can share with me?
>>>>
>>>> >> Thanks,
>>>> >> Sheldon
>
>
> My son has a model 228160 that *appears* (according to the picture of the
> AMT lathe at owwm.com) to be the same lathe.
> He has the owners manual for his lathe.
> If you don't have any luck finding a source, I can make a copy of this
> manual and send it to you.
>
> Max
I just checked Sears "parts" and found this:
http://tinyurl.com/qv7r2f
or:
http://www.searspartsdirect.com/partsdirect/searchByPartDescAction!searchByPartDescription.pd?brandId=0247&productCategoryId=0728000&modelNumber=113228160&backToLink=Return+to+Sub+Components+list&partDescription=manual
On Jun 1, 8:11=A0pm, [email protected] wrote:
> Thanks to everyone who has responded. =A0I have checked all the
> suggested sites. =A0I haven't found anything that has matched.
>
> I emailed Sears directly to see if they had any information. =A0After
> half a dozen frustrating emails the closest they could find in their
> database was 101.28950 where I was looking for 28955. =A0Their model
> number was for a 12" Craftsman Metal lathe made by Clausing Corp
> Services. =A0It seems that they are now Atlas.
>
> The writing on the lathe is both in English and French. =A0Would that
> make a difference as to who made it?
>
>
>
> On Sat, 30 May 2009 23:04:02 -0700 (PDT), [email protected] wrote:
> >ssesOn May 30, 10:32=A0am, [email protected] wrote:
> >> Hi,
>
> >> I'm an amature hobbyist. =A0I just picked up a Sears Long Bed Wood
> >> Lathe, Model Number 28955 and six chisels off of Kijiji. =A0I have bee=
n
> >> searching the net for information and manuals on the lathe but with no
> >> success. =A0Does anyone have any information they can share with me?
>
> >> Thanks,
> >> Sheldon
>
> >The number that you found (28955) is more similar to those found on
> >Atlas metalworking lathes:http://www.lathes.co.uk/craftsman/page3.html
> >Atlas also supplied Sears with lathes using a prefix =93101=94 in the
> >model number.
> >I can=92t say for sure who made your lathe but, Atlas made both
> >metalworking as well as woodworking equipment:http://www.atlas-press.com=
/index.htm
>
> >(Maybe you know, but =93Sheldon=94 is also a brand of lathes:
> >http://www.lathes.co.uk/sheldon/index.html) <g>
> >-DG- Hide quoted text -
>
> - Show quoted text -
In another post where you described your lathe as having tubes for the
bed. Emerson Electric supplied Sears with some wood lathes using a
single tube (monotube) for the bed, whereas AMT (American Machine &
Tool) supplied some lathes with a bed using two tubes (1-1/4=94 dia).
Here=92s a picture of an AMT lathe: http://www.creeksidewoodshop.com/Creeks=
idewoodshop-Workshop/Lathe.JPG.
Maybe it=92s similar to yours. Sears had many suppliers:
http://www.owwm.com/craftsman/manufacturers.aspx?sort=3D1 AMT had a
prefix =93149=94 in its model number, but I had no luck searching for
149.28955. There are more experts on the OWWM website and they might
help you better if you post pictures there.
> So how, exactly, is that mish-mosh of results supposed to help the OP?
That "mish mosh" was simply an example of what the OP could easily
have found to answer his question in the first place.
Its one thing to bring a serious query to the group after researching
and finding a dearth of information or conflicting information and
quite another to use an OP here to substitute for a little personal
effort and responsibility.
Hell, he could have gone to most any decent Book Store and found three
or nine books on beginning turning and browsed through them while
sipping coffee and deciding if any were worth purchasing.
Then, after buying a basic set of turning tols and experimenting, he
might have formed a question or three worth the efforts of the readers
here.
<[email protected]> wrote in message
news:[email protected]...
> Hi,
>
> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
> searching the net for information and manuals on the lathe but with no
> success. Does anyone have any information they can share with me?
>
> Thanks,
> Sheldon
Is this the one you have or close to it. I have the same one I bought about
25 years , I would say it's a good for a hobbyist Mine has been apart for
about 5 years. I believe there still made under deferent names . What kind
of question do have, I also have the owners manual.
http://sacramento.craigslist.org/tls/1191457331.html
[email protected] wrote:
> Hi Len,
>
> I believe this pre-dates Craftsman. It doesn't have the Craftsman
> label. It only has the old Sears label. The only model number on it
> is 28955.
>
> Thanks.
>
You might find something over the "Old Woodworking Machines" web site at:
http://www.owwm.com/
--
Jack Novak
Buffalo, NY - USA
[email protected]
Hi There,
Maybe I didn't word my OP correctly. I'm looking for information on
the lathe itself, not about woodturning.
On Mon, 1 Jun 2009 13:20:48 -0700 (PDT), [email protected] wrote:
>
>> So how, exactly, is that mish-mosh of results supposed to help the OP?
>
>That "mish mosh" was simply an example of what the OP could easily
>have found to answer his question in the first place.
>
>Its one thing to bring a serious query to the group after researching
>and finding a dearth of information or conflicting information and
>quite another to use an OP here to substitute for a little personal
>effort and responsibility.
>
>Hell, he could have gone to most any decent Book Store and found three
>or nine books on beginning turning and browsed through them while
>sipping coffee and deciding if any were worth purchasing.
>
>Then, after buying a basic set of turning tols and experimenting, he
>might have formed a question or three worth the efforts of the readers
>here.
Hi Folks,.
The AMT lathe is the one! The picture is exactly like the one I have.
According to www.owwm.com it is an AMT Lathe Model 273. I have
emailed the company from where the picture came from to see if they
have an electronic manual they could share.
Thanks very much for the help.
Sheldon
On Mon, 1 Jun 2009 21:42:11 -0700 (PDT), [email protected] wrote:
>On Jun 1, 8:11 pm, [email protected] wrote:
>> Thanks to everyone who has responded. I have checked all the
>> suggested sites. I haven't found anything that has matched.
>>
>> I emailed Sears directly to see if they had any information. After
>> half a dozen frustrating emails the closest they could find in their
>> database was 101.28950 where I was looking for 28955. Their model
>> number was for a 12" Craftsman Metal lathe made by Clausing Corp
>> Services. It seems that they are now Atlas.
>>
>> The writing on the lathe is both in English and French. Would that
>> make a difference as to who made it?
>>
>>
>>
>> On Sat, 30 May 2009 23:04:02 -0700 (PDT), [email protected] wrote:
>> >ssesOn May 30, 10:32 am, [email protected] wrote:
>> >> Hi,
>>
>> >> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
>> >> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
>> >> searching the net for information and manuals on the lathe but with no
>> >> success. Does anyone have any information they can share with me?
>>
>> >> Thanks,
>> >> Sheldon
>>
>> >The number that you found (28955) is more similar to those found on
>> >Atlas metalworking lathes:http://www.lathes.co.uk/craftsman/page3.html
>> >Atlas also supplied Sears with lathes using a prefix 101 in the
>> >model number.
>> >I cant say for sure who made your lathe but, Atlas made both
>> >metalworking as well as woodworking equipment:http://www.atlas-press.com/index.htm
>>
>> >(Maybe you know, but Sheldon is also a brand of lathes:
>> >http://www.lathes.co.uk/sheldon/index.html) <g>
>> >-DG- Hide quoted text -
>>
>> - Show quoted text -
>
>In another post where you described your lathe as having tubes for the
>bed. Emerson Electric supplied Sears with some wood lathes using a
>single tube (monotube) for the bed, whereas AMT (American Machine &
>Tool) supplied some lathes with a bed using two tubes (1-1/4 dia).
>Heres a picture of an AMT lathe: http://www.creeksidewoodshop.com/Creeksidewoodshop-Workshop/Lathe.JPG.
>Maybe its similar to yours. Sears had many suppliers:
>http://www.owwm.com/craftsman/manufacturers.aspx?sort=1 AMT had a
>prefix 149 in its model number, but I had no luck searching for
>149.28955. There are more experts on the OWWM website and they might
>help you better if you post pictures there.
<[email protected]> wrote in message
news:[email protected]...
> Hi,
>
> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
> searching the net for information and manuals on the lathe but with no
> success. Does anyone have any information they can share with me?
>
> Thanks,
> Sheldon
Is this a 'Craftsman' lathe? If so, what's the full (8 - 10 digits)
model number? There should be a plate or sticker somewhere with that
info.
Len
, [email protected] wrote:
>>> >> Hi,
>>>
>>> >> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
>>> >> Lathe, Model Number 28955 and six chisels off of Kijiji. I have been
>>> >> searching the net for information and manuals on the lathe but with
>>> >> no
>>> >> success. Does anyone have any information they can share with me?
>>>
>>> >> Thanks,
>>> >> Sheldon
My son has a model 228160 that *appears* (according to the picture of the
AMT lathe at owwm.com) to be the same lathe.
He has the owners manual for his lathe.
If you don't have any luck finding a source, I can make a copy of this
manual and send it to you.
Max
Sounds like a 60's lathe maybe a 70. I remember it - but I had my 40's already
and still use that heavy iron model.
Len wrote:
> <[email protected]> wrote in message
> news:[email protected]...
>> Hi Len,
>>
>> I believe this pre-dates Craftsman. It doesn't have the Craftsman
>> label. It only has the old Sears label. The only model number on it
>> is 28955.
>>
>> Thanks.
>>
>
> If it's that old, I suspect it may have actually been made by Emerson
> for Sears.
>
> Emerson now makes the 'Rigid' line for Home Depot, so you might want to
> take a look at the manual for the Rigid Model 14773 lathe to see if it's
> close enough. Click on the "book" just about the picture at
> http://www.ridgid.com/Tools/WL1200-Wood-Lathe/ to access the owners
> manual.
>
> If that's not it, try looking for a Emerson lathe manual instead of
> Sears.
>
> Len
>
Sorry,
I just discovered that this lathe was manufactured by Emerson.
"Max" <[email protected]> wrote in message
news:[email protected]...
>
> "Max" <[email protected]> wrote in message
> news:[email protected]...
>>
>>
>> , [email protected] wrote:
>>>>> >> Hi,
>>>>>
>>>>> >> I'm an amature hobbyist. I just picked up a Sears Long Bed Wood
>>>>> >> Lathe, Model Number 28955 and six chisels off of Kijiji. I have
>>>>> >> been
>>>>> >> searching the net for information and manuals on the lathe but with
>>>>> >> no
>>>>> >> success. Does anyone have any information they can share with me?
>>>>>
>>>>> >> Thanks,
>>>>> >> Sheldon
>>
>>
>> My son has a model 228160 that *appears* (according to the picture of the
>> AMT lathe at owwm.com) to be the same lathe.
>> He has the owners manual for his lathe.
>> If you don't have any luck finding a source, I can make a copy of this
>> manual and send it to you.
>>
>> Max
>
> I just checked Sears "parts" and found this:
> http://tinyurl.com/qv7r2f
> or:
> http://www.searspartsdirect.com/partsdirect/searchByPartDescAction!searchByPartDescription.pd?brandId=0247&productCategoryId=0728000&modelNumber=113228160&backToLink=Return+to+Sub+Components+list&partDescription=manual