In article <[email protected]>, Max
<[email protected]> wrote:
> By chance, is there anyone here who would happen to know which SCMS (with a
> ten inch blade preferably) has the widest (longest?) cutting ability.
> I want to replace a radial arm saw and I want the widest possible cut.
>
> TIA.
> Max
Dewalt makes a 12" blade model that cuts 16" with some alterations to
raise the table to take full advantage of the blade diameter.
I have a 10" Makita, love the saw but it is heavy and it has a large
footprint, though not as heavy as other brands. If it will only sit on
a bench in your shop this is not important.
I have used an 8 1/2" Dewalt and would actually love to have a smaller
saw like it, I am short, 5' 7" and find reaching around the Makita to
tilt the blade a bit awkward, I have also used a 12" Makita and it is
even more so. This has to do with the design of the bench it is sitting
on in the shop, at a site on a workmate it is easier to step around it.
Most dimensional lumber falls within the 12" cutting capacity anything
wider is usually a panel and I would cut that on the table saw with a
sled.
Frank C.
--
http:sawdustmaking.com
On Oct 31, 4:19 pm, "Max" <[email protected]> wrote:
> By chance, is there anyone here who would happen to know which SCMS (with a
> ten inch blade preferably) has the widest (longest?) cutting ability.
> I want to replace a radial arm saw and I want the widest possible cut.
>
> TIA.
> Max
I have a Hitachi C10FSH (10") and I can crosscut a 1x12 with no
problems. I think it could go maybe 1/2" further, but I've never
really tried.
With my saw I've cut 2' wide pieces of plywood with no problems by
just flipping it over and lining it up. The only thing I don't like is
the handle. It's parallel to the blade, not perpendicular, and makes
left hand cutting a PITA.
-Nathan
On Oct 31, 8:43 pm, "Max" <[email protected]> wrote:
> "Swingman" <[email protected]> wrote in message
>
> news:[email protected]...
>
>
>
>
>
> > "Max" wrote in message
> >> By chance, is there anyone here who would happen to know which SCMS (with
> > a
> >> ten inch blade preferably) has the widest (longest?) cutting ability.
> >> I want to replace a radial arm saw and I want the widest possible cut.
>
> > I think you'll find that they all max out at 12" cross cut capacity for a
> > 10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which
> > do.
>
> > A 12", like the DeWalt, should get you up to around a 16" cross cut
> > capacity.
>
> > --
> >www.e-woodshop.net
> > Last update: 10/25/07
> > KarlC@ (the obvious)
>
> I might have to go to a 12". hmmm. :-(
> Thanks,
>
> Max
The only way I know of to get a 12" to go all the way up to a 16" cut
is to buy or use a special accessory that raises up the level of the
table to the maximum diameter of the blade. I'm pretty sure DeWalt
makes one, but I don't know anything else about it.
On Nov 1, 7:15 am, "Jon" <[email protected]> wrote:
> The Makita LS1013 you can control the depth of cut, it does make pretty nice
> dado's using a Freud blade. Just mark the borders with a scribe and have at
> it.
>
> Jon
>
> "Max" <[email protected]> wrote in message
>
> news:Ni9Wi.7742$%[email protected]...
>
>
>
> > "Swingman" <[email protected]> wrote in message
> >news:[email protected]...
>
> >> "Max" wrote in message
> >>> By chance, is there anyone here who would happen to know which SCMS
> >>> (with
> >> a
> >>> ten inch blade preferably) has the widest (longest?) cutting ability.
> >>> I want to replace a radial arm saw and I want the widest possible cut.
>
> >> I think you'll find that they all max out at 12" cross cut capacity for a
> >> 10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which
> >> do.
>
> >> A 12", like the DeWalt, should get you up to around a 16" cross cut
> >> capacity.
>
> >> --
> >>www.e-woodshop.net
> >> Last update: 10/25/07
> >> KarlC@ (the obvious)
>
> > I might have to go to a 12". hmmm. :-(
> > Thanks,
>
> > Max
And conveniently enough, the LS1013F is at Amazon for $499, plus you
get a $50 gift card for another purchase at Amazon. Not too shabby!
On Oct 31, 8:43 pm, "Max" <[email protected]> wrote:
> "Swingman" <[email protected]> wrote in message
>
> news:[email protected]...
>
>
>
>
>
> > "Max" wrote in message
> >> By chance, is there anyone here who would happen to know which SCMS (with
> > a
> >> ten inch blade preferably) has the widest (longest?) cutting ability.
> >> I want to replace a radial arm saw and I want the widest possible cut.
>
> > I think you'll find that they all max out at 12" cross cut capacity for a
> > 10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which
> > do.
>
> > A 12", like the DeWalt, should get you up to around a 16" cross cut
> > capacity.
>
> > --
> >www.e-woodshop.net
> > Last update: 10/25/07
> > KarlC@ (the obvious)
>
> I might have to go to a 12". hmmm. :-(
> Thanks,
>
> Max
I've lusted after a scms for a couple of years now, but with limited
space at home just haven't brought myself to spending the money on
one ... yet.
Anyway, one consideration is the cost of 12" blades vs. 10" blades,
especially if you want to stock a variety of blades to use for
different tasks.
Mark
p.s. when/if I do get one, it'll likely be a 10" Bosch 4410L or the
Makita LS1013
On Nov 1, 12:57 pm, mac davis <[email protected]> wrote:
> On Thu, 01 Nov 2007 03:18:06 GMT, "Max" <[email protected]> wrote:
>
> <snip>
>
> >I *think* there's a Bosch with belt drive.
> >http://tinyurl.com/275qu3
>
> >I'm giving that saw some serious consideration.
> >You're right about using the proper blade. I've heard some real stories.
>
> >Thanks again for the input.
>
> >Max
>
> I don't know if this is a consideration, but early slide saws got a lot of
> complaints that the slider flexed on long cuts and they weren't as accurate as
> non-sliders... Maybe this has been corrected or was just a myth..
> Possibly just a problem on cheap saws?
>
> mac
>
> Please remove splinters before emailing
I've noticed that the slider (often) consists of two bars. I've seen
them side-by-side on some models, and one-atop-the-other on other
models. I'd expect the side-by-side design to have a lot less
sideways play. Does anyone have experience with both types to confirm
this?
Mark
On Nov 3, 8:59 pm, "Max" <[email protected]> wrote:
> "redbelly" wrote
>
> > I've lusted after a scms for a couple of years now, but with limited
> > space at home just haven't brought myself to spending the money on
> > one ... yet.
>
> > Anyway, one consideration is the cost of 12" blades vs. 10" blades,
> > especially if you want to stock a variety of blades to use for
> > different tasks.
>
> > Mark
>
> > p.s. when/if I do get one, it'll likely be a 10" Bosch 4410L or the
> > Makita LS1013
>
> It hadn't occurred to me to consider different blades. How many different
> tasks could one do with a *miter* saw?
>
> Max
I was thinking more of cutting different materials with it. If you're
just going to cut wood, and never plastic, aluminum, or steel, then
probably one blade would suit you.
Mark
On Nov 4, 12:22 pm, mac davis <[email protected]> wrote:
> On Sun, 04 Nov 2007 12:09:41 -0000, redbelly <[email protected]> wrote:
> >On Nov 3, 8:59 pm, "Max" <[email protected]> wrote:
> >> "redbelly" wrote
>
> >> > I've lusted after a scms for a couple of years now, but with limited
> >> > space at home just haven't brought myself to spending the money on
> >> > one ... yet.
>
> >> > Anyway, one consideration is the cost of 12" blades vs. 10" blades,
> >> > especially if you want to stock a variety of blades to use for
> >> > different tasks.
>
> >> > Mark
>
> >> > p.s. when/if I do get one, it'll likely be a 10" Bosch 4410L or the
> >> > Makita LS1013
>
> >> It hadn't occurred to me to consider different blades. How many different
> >> tasks could one do with a *miter* saw?
>
> >> Max
>
> >I was thinking more of cutting different materials with it. If you're
> >just going to cut wood, and never plastic, aluminum, or steel, then
> >probably one blade would suit you.
>
> >Mark
>
> I don't have a slider, so I pretty much use a "general purpose" blade on it..
>
> Comparing a slider to a RAS, however, I'd want both a cross cut and plywood
> blade, I think..
>
> I use crosscut, rip, dado and plywood blades on the RAS, so would you use the
> same on a CMS with a slider?
>
>
No. You don't need a rip and can't use a dado. The arbor isn't long
enough.
Jon <[email protected]> wrote:
Ditto for Bosh 4410. Depth of cut control, no problems making dados, very
comfortable, dual bevel, front control, precise. Highly recommended, I
simply love it.
> The Makita LS1013 you can control the depth of cut, it does make pretty nice
> dado's using a Freud blade. Just mark the borders with a scribe and have at
> it.
> Jon
> "Max" <[email protected]> wrote in message
> news:Ni9Wi.7742$%[email protected]...
>>
>> "Swingman" <[email protected]> wrote in message
>> news:[email protected]...
>>>
>>> "Max" wrote in message
>>>> By chance, is there anyone here who would happen to know which SCMS
>>>> (with
>>> a
>>>> ten inch blade preferably) has the widest (longest?) cutting ability.
>>>> I want to replace a radial arm saw and I want the widest possible cut.
>>>
>>> I think you'll find that they all max out at 12" cross cut capacity for a
>>> 10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which
>>> do.
>>>
>>> A 12", like the DeWalt, should get you up to around a 16" cross cut
>>> capacity.
>>>
>>> --
>>> www.e-woodshop.net
>>> Last update: 10/25/07
>>> KarlC@ (the obvious)
>>
>> I might have to go to a 12". hmmm. :-(
>> Thanks,
>>
>> Max
>>
>>
>>
---
******************************************************************
* KSI@home KOI8 Net < > The impossible we do immediately. *
* Las Vegas NV, USA < > Miracles require 24-hour notice. *
******************************************************************
--
Posted via a free Usenet account from http://www.teranews.com
"Max" <[email protected]> wrote in message
news:[email protected]...
>
> "mac davis" <[email protected]> wrote in message
> news:[email protected]...
>> On Thu, 01 Nov 2007 03:18:06 GMT, "Max" <[email protected]>
>> wrote:
>>
>> <snip>
>>
>>>I *think* there's a Bosch with belt drive.
>>>http://tinyurl.com/275qu3
>>>
>>>I'm giving that saw some serious consideration.
>>>You're right about using the proper blade. I've heard some real stories.
>>>
>>>Thanks again for the input.
>>>
>>>Max
>>>
>> I don't know if this is a consideration, but early slide saws got a lot
>> of
>> complaints that the slider flexed on long cuts and they weren't as
>> accurate as
>> non-sliders... Maybe this has been corrected or was just a myth..
>> Possibly just a problem on cheap saws?
>>
>>
>> mac
>>
>> Please remove splinters before emailing
>
> Yup. Some of the reviews I read mentioned that problem. Particularly the
> DeWalt.
> Still thinking Bosch.
>
I have the 12" Dewalt slider and don't have any problems with wandering on
any cuts. When I switched to a slider from the Dewalt 12" chopsaw I was
concerned, and even kept the old saw setup, but never had any problems.
Good luck with your purchase.
"Max" wrote in message
> By chance, is there anyone here who would happen to know which SCMS (with
a
> ten inch blade preferably) has the widest (longest?) cutting ability.
> I want to replace a radial arm saw and I want the widest possible cut.
I think you'll find that they all max out at 12" cross cut capacity for a
10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which do.
A 12", like the DeWalt, should get you up to around a 16" cross cut
capacity.
--
www.e-woodshop.net
Last update: 10/25/07
KarlC@ (the obvious)
"Swingman" <[email protected]> wrote in message
news:[email protected]...
>
> "Max" wrote in message
>> By chance, is there anyone here who would happen to know which SCMS (with
> a
>> ten inch blade preferably) has the widest (longest?) cutting ability.
>> I want to replace a radial arm saw and I want the widest possible cut.
>
> I think you'll find that they all max out at 12" cross cut capacity for a
> 10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which
> do.
>
> A 12", like the DeWalt, should get you up to around a 16" cross cut
> capacity.
>
> --
> www.e-woodshop.net
> Last update: 10/25/07
> KarlC@ (the obvious)
I might have to go to a 12". hmmm. :-(
Thanks,
Max
"goaway" wrote
> Max
> There are two features you would lose. The first is dado. The
> second is the ability to set the cut depth. Never tried this on my sliding
> compound. What you gain is very fast and easy and accurate angle changes
> and space. BTW make sure you get the right blades for the SCMS. Really
> ugly things happen with wrong blades, I will personally attest to this.
> Certain Brother in Law swapped a blade out without checking what he put
> in. VERY VERY UGLY AND VERY DANGEROUS THINGS HAPPEN
> Keep in mind the Dewalts use a belt drive, most others are direct drive.
> Not sure that matters, but I would keep a spare belt if I had a DeWalt.
> Good luck
>
> Paul
Thanks, Paul
I very, very rarely cut dadoes with a saw. I use a router. *Mostly* because
of the odd sizes for plywood ( I have the odd size bits) and the ease of
setting up.
(I have 9 routers) And I have (homemade) cutting guides for three of them.
I *think* there's a Bosch with belt drive.
http://tinyurl.com/275qu3
I'm giving that saw some serious consideration.
You're right about using the proper blade. I've heard some real stories.
Thanks again for the input.
Max
"mac davis" <[email protected]> wrote in message
news:[email protected]...
> On Thu, 01 Nov 2007 03:18:06 GMT, "Max" <[email protected]>
> wrote:
>
> <snip>
>
>>I *think* there's a Bosch with belt drive.
>>http://tinyurl.com/275qu3
>>
>>I'm giving that saw some serious consideration.
>>You're right about using the proper blade. I've heard some real stories.
>>
>>Thanks again for the input.
>>
>>Max
>>
> I don't know if this is a consideration, but early slide saws got a lot of
> complaints that the slider flexed on long cuts and they weren't as
> accurate as
> non-sliders... Maybe this has been corrected or was just a myth..
> Possibly just a problem on cheap saws?
>
>
> mac
>
> Please remove splinters before emailing
Yup. Some of the reviews I read mentioned that problem. Particularly the
DeWalt.
Still thinking Bosch.
Max
"Frank Campbell" <[email protected]> wrote in message
news:031120070818502559%[email protected]...
> In article <[email protected]>, Max
> <[email protected]> wrote:
>
>> By chance, is there anyone here who would happen to know which SCMS (with
>> a
>> ten inch blade preferably) has the widest (longest?) cutting ability.
>> I want to replace a radial arm saw and I want the widest possible cut.
>>
>> TIA.
>> Max
>
> Dewalt makes a 12" blade model that cuts 16" with some alterations to
> raise the table to take full advantage of the blade diameter.
>
> I have a 10" Makita, love the saw but it is heavy and it has a large
> footprint, though not as heavy as other brands. If it will only sit on
> a bench in your shop this is not important.
>
> I have used an 8 1/2" Dewalt and would actually love to have a smaller
> saw like it, I am short, 5' 7" and find reaching around the Makita to
> tilt the blade a bit awkward, I have also used a 12" Makita and it is
> even more so. This has to do with the design of the bench it is sitting
> on in the shop, at a site on a workmate it is easier to step around it.
>
> Most dimensional lumber falls within the 12" cutting capacity anything
> wider is usually a panel and I would cut that on the table saw with a
> sled.
> Frank C.
>
> --
> http:sawdustmaking.com
I rarely do crosscuts on the table saw. I have my radial arm saw "tuned" for
accurate crosscuts. If I need more crosscut capacity I use a circular saw
with a guide made especially for the job. I want a good sliding compound
miter saw to replace the radial arm saw and for some miters. I have a miter
sled for my table saw that allows me to do accurate miters but I would
rather have a saw dedicated to the job, ie a SCMS. Having a little extra
capacity for 90 degree cuts would be a plus.
I've been looking at the Bosch 5412L.
Max
"klaatu" <[email protected]> wrote in message
news:[email protected]...
> On Wed, 31 Oct 2007 18:43:23 -0600, "Max"
> <[email protected]> wrote:
>
>>
>>"Swingman" <[email protected]> wrote in message
>>news:[email protected]...
>>>
>>> "Max" wrote in message
>>>> By chance, is there anyone here who would happen to know which SCMS
>>>> (with
>>> a
>>>> ten inch blade preferably) has the widest (longest?) cutting ability.
>>>> I want to replace a radial arm saw and I want the widest possible cut.
>>>
>>> I think you'll find that they all max out at 12" cross cut capacity for
>>> a
>>> 10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which
>>> do.
>>>
>>> A 12", like the DeWalt, should get you up to around a 16" cross cut
>>> capacity.
>>>
>>> --
>>> www.e-woodshop.net
>>> Last update: 10/25/07
>>> KarlC@ (the obvious)
>>
>>I might have to go to a 12". hmmm. :-(
>>Thanks,
>>
>>Max
>>
>>
> If you can hold off until Nov. 9 thru 11, take a look at
> tools-plus.com. They will have discounts on those
> days. Their prices are usually as good as Amazon
> or close. I got my TS ,jointer and planer from them.
> Look at the Makita LS1214FL Compound Miter Saw.
> $599 now and maybe 10% off on above dates.
I can hold !! If I'm buying someplace besides Amazon the prices have to be
*better*.
I have gotten very good service from Amazon.
But, Thanks.
Max
On Thu, 01 Nov 2007 03:18:06 GMT, "Max" <[email protected]> wrote:
<snip>
>I *think* there's a Bosch with belt drive.
>http://tinyurl.com/275qu3
>
>I'm giving that saw some serious consideration.
>You're right about using the proper blade. I've heard some real stories.
>
>Thanks again for the input.
>
>Max
>
I don't know if this is a consideration, but early slide saws got a lot of
complaints that the slider flexed on long cuts and they weren't as accurate as
non-sliders... Maybe this has been corrected or was just a myth..
Possibly just a problem on cheap saws?
mac
Please remove splinters before emailing
On Sun, 04 Nov 2007 12:09:41 -0000, redbelly <[email protected]> wrote:
>On Nov 3, 8:59 pm, "Max" <[email protected]> wrote:
>> "redbelly" wrote
>>
>> > I've lusted after a scms for a couple of years now, but with limited
>> > space at home just haven't brought myself to spending the money on
>> > one ... yet.
>>
>> > Anyway, one consideration is the cost of 12" blades vs. 10" blades,
>> > especially if you want to stock a variety of blades to use for
>> > different tasks.
>>
>> > Mark
>>
>> > p.s. when/if I do get one, it'll likely be a 10" Bosch 4410L or the
>> > Makita LS1013
>>
>> It hadn't occurred to me to consider different blades. How many different
>> tasks could one do with a *miter* saw?
>>
>> Max
>
>I was thinking more of cutting different materials with it. If you're
>just going to cut wood, and never plastic, aluminum, or steel, then
>probably one blade would suit you.
>
>Mark
I don't have a slider, so I pretty much use a "general purpose" blade on it..
Comparing a slider to a RAS, however, I'd want both a cross cut and plywood
blade, I think..
I use crosscut, rip, dado and plywood blades on the RAS, so would you use the
same on a CMS with a slider?
mac
Please remove splinters before emailing
On Wed, 31 Oct 2007 18:43:23 -0600, "Max" <[email protected]> wrote:
<snip>
>>
>> A 12", like the DeWalt, should get you up to around a 16" cross cut
>> capacity.
>>
>> --
>> www.e-woodshop.net
>> Last update: 10/25/07
>> KarlC@ (the obvious)
>
>I might have to go to a 12". hmmm. :-(
>Thanks,
>
>Max
>
I have a RAS in addition to my 10" CMS..
My brother bought the 12" and loves it... sliding or not, he figures bigger is
better..lol
mac
Please remove splinters before emailing
The Makita LS1013 you can control the depth of cut, it does make pretty nice
dado's using a Freud blade. Just mark the borders with a scribe and have at
it.
Jon
"Max" <[email protected]> wrote in message
news:Ni9Wi.7742$%[email protected]...
>
> "Swingman" <[email protected]> wrote in message
> news:[email protected]...
>>
>> "Max" wrote in message
>>> By chance, is there anyone here who would happen to know which SCMS
>>> (with
>> a
>>> ten inch blade preferably) has the widest (longest?) cutting ability.
>>> I want to replace a radial arm saw and I want the widest possible cut.
>>
>> I think you'll find that they all max out at 12" cross cut capacity for a
>> 10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which
>> do.
>>
>> A 12", like the DeWalt, should get you up to around a 16" cross cut
>> capacity.
>>
>> --
>> www.e-woodshop.net
>> Last update: 10/25/07
>> KarlC@ (the obvious)
>
> I might have to go to a 12". hmmm. :-(
> Thanks,
>
> Max
>
>
>
"redbelly" wrote
> I've lusted after a scms for a couple of years now, but with limited
> space at home just haven't brought myself to spending the money on
> one ... yet.
>
> Anyway, one consideration is the cost of 12" blades vs. 10" blades,
> especially if you want to stock a variety of blades to use for
> different tasks.
>
> Mark
>
> p.s. when/if I do get one, it'll likely be a 10" Bosch 4410L or the
> Makita LS1013
It hadn't occurred to me to consider different blades. How many different
tasks could one do with a *miter* saw?
Max
Max
There are two features you would lose. The first is dado. The second
is the ability to set the cut depth. Never tried this on my sliding
compound. What you gain is very fast and easy and accurate angle changes and
space. BTW make sure you get the right blades for the SCMS. Really ugly
things happen with wrong blades, I will personally attest to this. Certain
Brother in Law swapped a blade out without checking what he put in. VERY
VERY UGLY AND VERY DANGEROUS THINGS HAPPEN
Keep in mind the Dewalts use a belt drive, most others are direct drive. Not
sure that matters, but I would keep a spare belt if I had a DeWalt. Good
luck
Paul
"Max" <[email protected]> wrote in message
news:[email protected]...
> By chance, is there anyone here who would happen to know which SCMS (with
> a ten inch blade preferably) has the widest (longest?) cutting ability.
> I want to replace a radial arm saw and I want the widest possible cut.
>
> TIA.
> Max
>
"redbelly" <[email protected]> wrote in message
news:[email protected]...
> I've noticed that the slider (often) consists of two bars. I've seen
> them side-by-side on some models, and one-atop-the-other on other
> models. I'd expect the side-by-side design to have a lot less
> sideways play. Does anyone have experience with both types to confirm
> this?
>
> Mark
I was wondering the same thing. Glad you asked.
Max
On Wed, 31 Oct 2007 18:43:23 -0600, "Max"
<[email protected]> wrote:
>
>"Swingman" <[email protected]> wrote in message
>news:[email protected]...
>>
>> "Max" wrote in message
>>> By chance, is there anyone here who would happen to know which SCMS (with
>> a
>>> ten inch blade preferably) has the widest (longest?) cutting ability.
>>> I want to replace a radial arm saw and I want the widest possible cut.
>>
>> I think you'll find that they all max out at 12" cross cut capacity for a
>> 10" SCMS. I have the Makita LS1013 and I've used a Bosch, both of which
>> do.
>>
>> A 12", like the DeWalt, should get you up to around a 16" cross cut
>> capacity.
>>
>> --
>> www.e-woodshop.net
>> Last update: 10/25/07
>> KarlC@ (the obvious)
>
>I might have to go to a 12". hmmm. :-(
>Thanks,
>
>Max
>
>
If you can hold off until Nov. 9 thru 11, take a look at
tools-plus.com. They will have discounts on those
days. Their prices are usually as good as Amazon
or close. I got my TS ,jointer and planer from them.
Look at the Makita LS1214FL Compound Miter Saw.
$599 now and maybe 10% off on above dates.
"redbelly" <[email protected]> wrote in message
news:[email protected]...
> On Nov 3, 8:59 pm, "Max" <[email protected]> wrote:
>> "redbelly" wrote
>>
>> > I've lusted after a scms for a couple of years now, but with limited
>> > space at home just haven't brought myself to spending the money on
>> > one ... yet.
>>
>> > Anyway, one consideration is the cost of 12" blades vs. 10" blades,
>> > especially if you want to stock a variety of blades to use for
>> > different tasks.
>>
>> > Mark
>>
>> > p.s. when/if I do get one, it'll likely be a 10" Bosch 4410L or the
>> > Makita LS1013
>>
>> It hadn't occurred to me to consider different blades. How many
>> different
>> tasks could one do with a *miter* saw?
>>
>> Max
>
> I was thinking more of cutting different materials with it. If you're
> just going to cut wood, and never plastic, aluminum, or steel, then
> probably one blade would suit you.
>
> Mark
I have a chop saw for steel. And a power hack saw. And a cutting torch.
Can't say for sure that I would never want to cut plastic or aluminum.
Hmmm.
Max
"Frank Drackman" <[email protected]> wrote in message
news:[email protected]...
>
> "Max" <[email protected]> wrote in message
> news:[email protected]...
>>
>> "mac davis" <[email protected]> wrote in message
>> news:[email protected]...
>>> On Thu, 01 Nov 2007 03:18:06 GMT, "Max" <[email protected]>
>>> wrote:
>>>
>>> <snip>
>>>
>>>>I *think* there's a Bosch with belt drive.
>>>>http://tinyurl.com/275qu3
>>>>
>>>>I'm giving that saw some serious consideration.
>>>>You're right about using the proper blade. I've heard some real stories.
>>>>
>>>>Thanks again for the input.
>>>>
>>>>Max
>>>>
>>> I don't know if this is a consideration, but early slide saws got a lot
>>> of
>>> complaints that the slider flexed on long cuts and they weren't as
>>> accurate as
>>> non-sliders... Maybe this has been corrected or was just a myth..
>>> Possibly just a problem on cheap saws?
>>>
>>>
>>> mac
>>>
>>> Please remove splinters before emailing
>>
>> Yup. Some of the reviews I read mentioned that problem. Particularly the
>> DeWalt.
>> Still thinking Bosch.
>>
>
>
> I have the 12" Dewalt slider and don't have any problems with wandering on
> any cuts. When I switched to a slider from the Dewalt 12" chopsaw I was
> concerned, and even kept the old saw setup, but never had any problems.
>
> Good luck with your purchase.
Thank you, Sir. There's no such thing as too much advice. Just sort it out.
<G>
Max