Sorry for the basic question, but I find I have a lot of trouble laying
out accurate curves when marking out cuts. For example, right now I am
making a small table for a theater set that will have flat cutout
cabriole legs cut from 1/2" plywood. When I am marking the curves on
the wood to be cut, I can't seem to get a smooth single line. Any
suggestions?
Thanks,
Richard
if you can get a set of french curves to the scale of your work, they
help a lot. they take a bit of fussing with, but the result is worth
it.
you can also use a sprung lath and some ducks or pins.
sometimes I do a lot of it by eye- first at arms length with a big
pencil, get the curve approximate- really just to scale. then use a
rule and find any spots that have to be located- the length of the leg
and the points where it fastens to the apron in your case. then lay it
flat on a high bench and get your eye down to a low angle so you are
seeing a lot of foreshortening. at this angle you can only judge a
short section of curve at a time, but you can really see the fairness
of that section. you'll have to rotate the sheet about to maintain a
useful angle and stand it up frequently to check it at arm's length.
with this method it is possible to make some very pretty curves at any
scale you wish.
I personnaly use CAD and just plot it out but you can create a ships
curve by just using a very thin piece of stock or edge banding and
setting some pins (nails) at specific points on the curve and bending
the stock around the pins. Just do some grid work on the original
drawing to determine the x-y location of the salient points on the
curve.
You can create a thin piece of stock by ripping a 4/4 board at the
table saw just to straighten one edge, then kick the fence over the
thickness of the blade + a shy 1/8" and rip it again, leaving a nice
thin piece of drop.
darkon wrote:
> Richard <[email protected]> wrote:
>
> > Sorry for the basic question, but I find I have a lot of trouble
> > laying out accurate curves when marking out cuts. For example,
> > right now I am making a small table for a theater set that will
> > have flat cutout cabriole legs cut from 1/2" plywood. When I am
> > marking the curves on the wood to be cut, I can't seem to get a
> > smooth single line. Any suggestions?
>
> Yet another way: get a cheap metal yardstick or ruler, drill holes in
> each end, loop string or wire through the holes, tie the ends together,
> put a stick in the string, then twist the string to bow the yardstick.
> Twist until you get the curvature you want. Of course, if you want it
> TOO curved, you'll end up making a permanent kink in the
> yardstick/ruler, but I'm sure you can find other springy materials to
> make a bow from.
this is ok for regular curves- ones with a single radius. a trammel is
better, though, if you have room to use it.
a cabriole leg wants curves with smoothly changing radii, though.
Thanks for all the help everyone! I had never heard of ship curves, but
that is exactly the solution I was looking for. I have no trouble
laying out the lines in a scale plan with a french curve, but even
using a grid I was unable to connect the points smoothly. I think the
flexible straightedge will work perfectly.
Thanks,
Richard
On 11 Aug 2005 10:56:28 -0700, "Richard" <[email protected]> wrote:
>When I am marking the curves on
>the wood to be cut, I can't seem to get a smooth single line. Any
>suggestions?
Do it first on suitably stiff cardboard. When "close" with a heavier
line, cut that carefully. Use as a template and draw easily around it
on the wood. ...unless you're a total klutz, then get someone else to
do that part. I did a toybox, and put on some cartoon drawings I'd
spent a week [it felt like a week] copying from drawings copied
through the internet. Several stages to get what I wanted, since I
draw stick-people. My daughter painted the characters when the
outlines were done, or it would have looked like Hell. It now looks
great.
Richard wrote:
> Sorry for the basic question, but I find I have a lot of trouble laying
> out accurate curves when marking out cuts. For example, right now I am
> making a small table for a theater set that will have flat cutout
> cabriole legs cut from 1/2" plywood. When I am marking the curves on
> the wood to be cut, I can't seem to get a smooth single line. Any
> suggestions?
The magic word is "Batten", basically a flexible straight edge that
allows you to connect the dots along a curved shape.
You lay out a lot of cambers building a boat.
The following are a few methods I've used.
Large cambers, say 10-15 ft long.
Layout the points, the use a pilot drill for an 8d finish nail and
insert nail.
Use a flat aluminum bar, say 1" wide, 1/16" thick a8 96" long as a
batten placing it against nails and tracing the curve.
(SFWIW, have even used a piece of 1/2" PVC water pipe as a batten in a
pinch)
Cut curve proud and finish as req'd for the piece.
Small cambers such as might be found on a piece of furniture.
Use a flexible spline curve sold by a good drafting supply house.
They are about 18" long and can bent by hand to conform to the curve,
then trace curve.
Again, cut proud and finish as req'd.
HTH
Lew
Richard wrote:
> Sorry for the basic question, but I find I have a lot of trouble laying=
> out accurate curves when marking out cuts. For example, right now I am
> making a small table for a theater set that will have flat cutout
> cabriole legs cut from 1/2" plywood. When I am marking the curves on
> the wood to be cut, I can't seem to get a smooth single line. Any
> suggestions?
>=20
> Thanks,
> Richard
>=20
Buy a French curve. Available at fine (and not so fine) art and drafting =
supply stores.
--=20
Will R.
Jewel Boxes and Wood Art
http://woodwork.pmccl.com
The power of accurate observation is commonly called cynicism by those=20
who have not got it.=94 George Bernard Shaw
"Richard" <[email protected]> wrote in message
news:[email protected]...
> Sorry for the basic question, but I find I have a lot of trouble laying
> out accurate curves when marking out cuts. For example, right now I am
> making a small table for a theater set that will have flat cutout
> cabriole legs cut from 1/2" plywood. When I am marking the curves on
> the wood to be cut, I can't seem to get a smooth single line. Any
> suggestions?
>
> Thanks,
> Richard
Get a set of "ships" curves, they are longer and more suitable than "french
"curves...........mjh
Richard <[email protected]> wrote:
> Sorry for the basic question, but I find I have a lot of trouble
> laying out accurate curves when marking out cuts. For example,
> right now I am making a small table for a theater set that will
> have flat cutout cabriole legs cut from 1/2" plywood. When I am
> marking the curves on the wood to be cut, I can't seem to get a
> smooth single line. Any suggestions?
Yet another way: get a cheap metal yardstick or ruler, drill holes in
each end, loop string or wire through the holes, tie the ends together,
put a stick in the string, then twist the string to bow the yardstick.
Twist until you get the curvature you want. Of course, if you want it
TOO curved, you'll end up making a permanent kink in the
yardstick/ruler, but I'm sure you can find other springy materials to
make a bow from.
Make a template of 1/4 to 1/2 MDF or plywood. Freehand the curve onto that
and sand it to shape. Easier to sand something smooth than to sand something
jagged. Sanding will naturally flow things together. Once completed, use to
mark workpieces. An advantage is that they will all be the same.
"Richard" <[email protected]> wrote in message
news:[email protected]...
> Sorry for the basic question, but I find I have a lot of trouble laying
> out accurate curves when marking out cuts. For example, right now I am
> making a small table for a theater set that will have flat cutout
> cabriole legs cut from 1/2" plywood. When I am marking the curves on
> the wood to be cut, I can't seem to get a smooth single line. Any
> suggestions?
>
> Thanks,
> Richard
>