Today, my new Yorkcraft 8" jointer arrived. Over the weekend I was
thinking of how many people it would take to get the thing down to my
basement, and around a corner on the stairs. Looking at the crate, and
realizing how big this sucker really is, it may just have to live in the
basement.
Has anyone tried to get a monster like this down a flight of stairs with
a corner, without completly disassembling the thing? I'm thinking if it
goes downstairs at all, it may be easiest to do so while it's crated up.
But then, if I ever move, I'd probably have to disassemble and get it
back up in pieces.
Would moving straps work? I'm thinking of the ones I've seen movers put
over their shoulders to carry heavy appliances, pianos, etc. with two
people.
I like the idea, but I don't think it would work for me. The stairs
down to the basement have a landing and a right angle to negotiate. I
take it you had a straight flight of stairs, if so that would make sense
to use the stretcher to slide down.
Stephen M wrote:
> I took mine around a corner and up a flight of stairs.
>
>
> Here's how:
>
> I built a stretcher out of 2 2x4's. 2 7' long pieces, and 2 crossbars about
> a foot long. Assemble like a tall "H" with two crossbars. attach this to the
> bottom of the table assembly. Then you can lift from then ends while
> supporting from the center.
>
> For the stairs, we slid it on the stretcher.
>
> Does that make sense?
>
> We were able to do this with 2 40-ish not-especially-big guys. (but is was
> all we could handle).
>
> -Steve
>
>
>
>
> "Dave Miller" <[email protected]> wrote in message
> news:[email protected]...
>
>>Today, my new Yorkcraft 8" jointer arrived. Over the weekend I was
>>thinking of how many people it would take to get the thing down to my
>>basement, and around a corner on the stairs. Looking at the crate, and
>>realizing how big this sucker really is, it may just have to live in the
>>basement.
>>
>>Has anyone tried to get a monster like this down a flight of stairs with
>>a corner, without completly disassembling the thing? I'm thinking if it
>>goes downstairs at all, it may be easiest to do so while it's crated up.
>> But then, if I ever move, I'd probably have to disassemble and get it
>>back up in pieces.
>>
>>Would moving straps work? I'm thinking of the ones I've seen movers put
>>over their shoulders to carry heavy appliances, pianos, etc. with two
>>people.
>>
>
>
>
In article <[email protected]>, [email protected] says...
> Has anyone tried to get a monster like this down a flight of stairs with
> a corner, without completly disassembling the thing? I'm thinking if it
> goes downstairs at all, it may be easiest to do so while it's crated up.
> But then, if I ever move, I'd probably have to disassemble and get it
> back up in pieces.
>
Think rope and pulley. You'd have to rerig at the corner, which might
be difficult if there's no landing.
If it's a curve with no landing, rather than a 90 degree corner, it
might go all the way with the one rigging.
--
Homo sapiens is a goal, not a description
"Dave Miller" <[email protected]> wrote in message
news:[email protected]...
> Today, my new Yorkcraft 8" jointer arrived. Over the weekend I was
> thinking of how many people it would take to get the thing down to my
> basement, and around a corner on the stairs. Looking at the crate, and
> realizing how big this sucker really is, it may just have to live in the
> basement.
>
> Has anyone tried to get a monster like this down a flight of stairs with
> a corner, without completly disassembling the thing? I'm thinking if it
> goes downstairs at all, it may be easiest to do so while it's crated up.
> But then, if I ever move, I'd probably have to disassemble and get it
> back up in pieces.
>
> Would moving straps work? I'm thinking of the ones I've seen movers put
> over their shoulders to carry heavy appliances, pianos, etc. with two
> people.
>
If you have two people - rope and pulley is the way to go. If just carrying
it and someone slips going down the stairs - bad news.
Attach rope to unit. One person at top of stairs controls rope. Lower person
pulls the unit down - a stair at a time - upper person keeps tension on rope
and keeps it from sliding or dropping. Stop at the 90 degree landing.
Reposition and repeat. Should balance the load so that neither has the full
weight. Easier to do that explain .
Good luck -
Vic
If the jointer is removed from the base, a couple of strong guys should be
able to negotiate the stairs. I hope you enjoy your 8 inch Yorkcraft as much
as I enjoy mine. The YC-8 is a very under-rated machine, mine was way out
of adjustment when I got it. A dial indicator and a little persistance have
brought everything into line. Now it makes flat stock out of warped and
straight edges out of wainy.
Dave
I took mine around a corner and up a flight of stairs.
Here's how:
I built a stretcher out of 2 2x4's. 2 7' long pieces, and 2 crossbars about
a foot long. Assemble like a tall "H" with two crossbars. attach this to the
bottom of the table assembly. Then you can lift from then ends while
supporting from the center.
For the stairs, we slid it on the stretcher.
Does that make sense?
We were able to do this with 2 40-ish not-especially-big guys. (but is was
all we could handle).
-Steve
"Dave Miller" <[email protected]> wrote in message
news:[email protected]...
> Today, my new Yorkcraft 8" jointer arrived. Over the weekend I was
> thinking of how many people it would take to get the thing down to my
> basement, and around a corner on the stairs. Looking at the crate, and
> realizing how big this sucker really is, it may just have to live in the
> basement.
>
> Has anyone tried to get a monster like this down a flight of stairs with
> a corner, without completly disassembling the thing? I'm thinking if it
> goes downstairs at all, it may be easiest to do so while it's crated up.
> But then, if I ever move, I'd probably have to disassemble and get it
> back up in pieces.
>
> Would moving straps work? I'm thinking of the ones I've seen movers put
> over their shoulders to carry heavy appliances, pianos, etc. with two
> people.
>
"Dave Miller" <[email protected]> wrote in message
news:[email protected]...
> I like the idea, but I don't think it would work for me. The stairs
> down to the basement have a landing and a right angle to negotiate. I
> take it you had a straight flight of stairs, if so that would make sense
> to use the stretcher to slide down.
That was up.
The stretcher was only a couple inches longer than the jointer and the same
width. It removes any temptation to lift from the ends of the infeed and
outfeed (which I hear is a no-no).
I still think it could work for you just to give you safe holding and a
place to tie a rope if need be.
-s
try small wheels attached to a scrap of ply. but does not the yorkcraft
jointer have its own wheels? the thing to do would be to put some ply on the
stairs and let roll down under your control
good luck
Len
"Dave Miller" <[email protected]> wrote in message
news:[email protected]...
> Today, my new Yorkcraft 8" jointer arrived. Over the weekend I was
> thinking of how many people it would take to get the thing down to my
> basement, and around a corner on the stairs. Looking at the crate, and
> realizing how big this sucker really is, it may just have to live in the
> basement.
>
> Has anyone tried to get a monster like this down a flight of stairs with a
> corner, without completly disassembling the thing? I'm thinking if it
> goes downstairs at all, it may be easiest to do so while it's crated up.
> But then, if I ever move, I'd probably have to disassemble and get it back
> up in pieces.
>
> Would moving straps work? I'm thinking of the ones I've seen movers put
> over their shoulders to carry heavy appliances, pianos, etc. with two
> people.
>