I'm getting ready to make a new desk for my office and have ran into a bit
of a quandary. It's going to be made in sections so as to be able to get it
in and out of the room. The main question I have is how would one fasten the
leg panels to the top? I don't want to screw from the top down, but the leg
panels need to be removable. And l brackets would be seen, and I'd rather
not have that. But so far, that's my only way out. I'd really appreciate it
if I had a couple other suggestions. The leg panels are going to be on the
order of this desk from Staples.
http://www.staples.com/webapp/wcs/stores/servlet/StaplesProductDisplay?prodCatType=2&storeId=10001&catalogId=10051&langId=-1&productId=147397&cmArea=SEARCH
Just attaching the legs to the desk top. The desk itself is entirely
different. Thanks for any suggestions. BTW, I'm going to post a picture of
the desk in ABPW in case anyone is afraid to click the link.
Tim Taylor wrote:
> I'm getting ready to make a new desk for my office and have ran into a bit
> of a quandary. It's going to be made in sections so as to be able to get it
> in and out of the room. The main question I have is how would one fasten the
> leg panels to the top?
http://www.rockler.com/product.cfm?page=2334&SearchHandle=DADBDBDBDADADDDGDGGDDHDADCGFGEGFCNDFDBDGDBCNDEGFDFDECNGBDIGCDECNGEDIGGGBGGGDDEDCDGDGGGGFDADADADBDADADADBDBGLGECAGIGBHCGEHHGBHCGFDADADADEDADADADADADADADBDFDADADADBDADADADADADADADADADADADADBDADADADBDBGLGECAGIGBHCGEHHGBHCGFDADADADBDB&filter=kd%20hardware
If the link doesn't work, do search for knockdown or kd hardware
Duke of Burl wrote:
> Tim Taylor wrote:
> > I'm getting ready to make a new desk for my office and have ran into a bit
> > of a quandary. It's going to be made in sections so as to be able to get it
> > in and out of the room. The main question I have is how would one fasten the
> > leg panels to the top?
Did you google 'desk top fasteners' or 'table top fasteners'?
http://www.rockler.com/CategoryView.cfm?Cat_ID=150
"> FWIW, I have a store-bought wooden desk that has stood up fine through a
> half a dozen moves and is showing no sag or wobble after 25 years of use.
> I just pulled the drawers and examined the construction. Turns out that
> each pedestal has two pieces of steel angle securing the pedestal to the
> top, with the angle placed _inside_ the pedestal where it's not visible.
>
> If you have a pedestal with drawers on each side this would seem to be a
> very satisfactory solution. If it needs to be taken down regularly I'd
> put
> some threaded inserts in the wood rather than using wood screws--mine has
> never been apart.
> --
> --John
> to email, dial "usenet" and validate
> (was jclarke at eye bee em dot net)
Well I wasn't planning on having pedestals, just going to be flat panels. I
guess I could always mortise the angles in. That might not show too bad. I'm
still in the planning stage on the whole thing, so I'm still checking my
options. And no, it's not going to be taken apart on a regular basis. One I
get it in the room, it's going to stay. I don't think they'll let me bring
it to the funeral home, cause that's the next place I'm moving to! Thanks
John.
"Tim Taylor" <[email protected]> wrote in message
news:[email protected]...
>
> I'm getting ready to make a new desk for my office and have ran into a bit
> of a quandary. It's going to be made in sections so as to be able to get
> it in and out of the room. The main question I have is how would one
> fasten the leg panels to the top? I don't want to screw from the top down,
> but the leg panels need to be removable. And l brackets would be seen, and
> I'd rather not have that. But so far, that's my only way out. I'd really
> appreciate it if I had a couple other suggestions. The leg panels are
> going to be on the order of this desk from Staples.
>
> http://www.staples.com/webapp/wcs/stores/servlet/StaplesProductDisplay?prodCatType=2&storeId=10001&catalogId=10051&langId=-1&productId=147397&cmArea=SEARCH
>
> Just attaching the legs to the desk top. The desk itself is entirely
> different. Thanks for any suggestions. BTW, I'm going to post a picture of
> the desk in ABPW in case anyone is afraid to click the link.
>
Those things are put together with knock down or RTA (ready to assemble)
hardware. Just use what they use.
"Par" <[email protected]> wrote in message
news:[email protected]...
> Tim Taylor <[email protected]>:
>>
>> I'm getting ready to make a new desk for my office and have ran into a
>> bit
>> of a quandary. It's going to be made in sections so as to be able to get
>> it
>> in and out of the room. The main question I have is how would one fasten
>> the
>
> This might not be the way you want it, but I'm currently sitting by an
> oak desk that is from sometime in the latter half of the 19th century.
> Three parts; on my right is a set of drawers, hidden behind a door, on
> the left is a "cabinet", the desk itself has three drawers; one in the
> center and one over wash side. Basically the two sidepieces have a hole
> in the center (almost as large as the sides, minus 5 cm or so[1]), and
> the top has matching boards attached.
>
> All fits nicely together, and each piece is manageable by itself. For
> all I know it was more or less standard office furniture (it was used by
> a prison chaplain in his office before it started wandering down the
> familly).
>
> /Par
>
> [1] I can't recall the details, and would need to empty out -- and
> clean! -- the desk to be able to lift it up and check. I *think* it was
> "octagonal" holes in the top, and four boards matching the "corners" on
> the top. ASCII art time:
>
> _______
> / \ / / \ \
> / \ / / \ \
> | |
> | |
> \ / \ \ / /
> \_______/ \ \ / /
>
> Side Top
>
>
> --
> Par [email protected]
> Making mental lists of laws broken is an enjoyable pastime, but I
> recommend against putting it in writing. -- Alan J Rosenthal
Thanks Par. I think I catch what your getting at, but I'm trying not to have
anything but just a flat piece for the supports. I'll try the art thing.
___________________________________
I I
I I
I I
I I
I I
The I's are just 3/4 flat panels. I don't have a whole lot of room where
this is going to put cabinets/drawers, They're going to be on the opposite
wall. But I do appreciate the help!
Tim Taylor wrote:
>
> "Jerry" <[email protected]> wrote in message
> news:[email protected]...
>> you can do the whole thing using Kreg Pocket hole screws... easy to
>> assemble and take apart.........Jerry
>>
>
> Yea I was thinking about pocket hole screws. They would be a lot less
> visible than brackets. I had also tossed the idea of the knock down
> hardware as Duke proposed, but I put together an el cheapo shelf with
> them. Maybe cause it was an el cheapo shelf, but I didn't like the way it
> had wobble in it. I'll do some more checking. Thanks everybody.
FWIW, I have a store-bought wooden desk that has stood up fine through a
half a dozen moves and is showing no sag or wobble after 25 years of use.
I just pulled the drawers and examined the construction. Turns out that
each pedestal has two pieces of steel angle securing the pedestal to the
top, with the angle placed _inside_ the pedestal where it's not visible.
If you have a pedestal with drawers on each side this would seem to be a
very satisfactory solution. If it needs to be taken down regularly I'd put
some threaded inserts in the wood rather than using wood screws--mine has
never been apart.
--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)
"Jerry" <[email protected]> wrote in message
news:[email protected]...
> you can do the whole thing using Kreg Pocket hole screws... easy to
> assemble and take apart.........Jerry
>
Yea I was thinking about pocket hole screws. They would be a lot less
visible than brackets. I had also tossed the idea of the knock down hardware
as Duke proposed, but I put together an el cheapo shelf with them. Maybe
cause it was an el cheapo shelf, but I didn't like the way it had wobble in
it. I'll do some more checking. Thanks everybody.
Tim Taylor <[email protected]>:
>
> I'm getting ready to make a new desk for my office and have ran into a bit
> of a quandary. It's going to be made in sections so as to be able to get it
> in and out of the room. The main question I have is how would one fasten the
This might not be the way you want it, but I'm currently sitting by an
oak desk that is from sometime in the latter half of the 19th century.
Three parts; on my right is a set of drawers, hidden behind a door, on
the left is a "cabinet", the desk itself has three drawers; one in the
center and one over wash side. Basically the two sidepieces have a hole
in the center (almost as large as the sides, minus 5 cm or so[1]), and
the top has matching boards attached.
All fits nicely together, and each piece is manageable by itself. For
all I know it was more or less standard office furniture (it was used by
a prison chaplain in his office before it started wandering down the
familly).
/Par
[1] I can't recall the details, and would need to empty out -- and
clean! -- the desk to be able to lift it up and check. I *think* it was
"octagonal" holes in the top, and four boards matching the "corners" on
the top. ASCII art time:
_______
/ \ / / \ \
/ \ / / \ \
| |
| |
\ / \ \ / /
\_______/ \ \ / /
Side Top
--
Par [email protected]
Making mental lists of laws broken is an enjoyable pastime, but I
recommend against putting it in writing. -- Alan J Rosenthal