I have an old 6" delta jointer that uses the pork chop style jointer
guard. However, I don't have the jointer guard, so I would like to
fabricate one but again I don't have one to start with. Does someone
have some specifcs about this item that they could share? Like how it
works? also if someone could share the dimensions of one that they
have but best of all would be if someone could trace the outline and
include dimensions. This way I could get one fabricated and have it be
pretty close to accurate.
Thanks,
Fred
[email protected] wrote:
> Bump
Um, it was only five hours since you posted that; there's no need to
"bump" it. A lot of people only read the group once a day, if even that
often. Maybe if nobody has answered in a week....
Beyond that, despite the fact that you're reading this on Google Groups
so it looks kind of like a web board, it's not. Most of us don't read
it using Google at all, but with other programs that do a much better
job of listing which messages we haven't read yet. So the fact that a
message is "off the front page" on Google doesn't mean that people won't
see it, and bumping doesn't help.
- Brooks (who unfortunately has no access to a 6" Delta jointer, so
can't help you there.)
--
The "bmoses-nospam" address is valid; no unmunging needed.
On 3 Feb 2006 11:10:27 -0800, [email protected] wrote:
>I have an old 6" delta jointer that uses the pork chop style jointer
>guard. However, I don't have the jointer guard, so I would like to
>fabricate one but again I don't have one to start with. Does someone
>have some specifcs about this item that they could share? Like how it
>works? also if someone could share the dimensions of one that they
>have but best of all would be if someone could trace the outline and
>include dimensions. This way I could get one fabricated and have it be
>pretty close to accurate.
Has anyone gotten back to you on this? I can take a picture and email
if you like.
You might also keep an eye on Ebay. It might take a week or two but
sooner or later I suspect one will show up. There's one on there now
for an 8".
Mike O.
But it does annoy people.
"Brooks Moses" <[email protected]> wrote in message
> bumping doesn't help.
>
>
Dip.
<[email protected]> wrote in message
news:[email protected]...
> Bump
>
Bang.
<[email protected]> wrote in message
news:[email protected]...
> Bump
>
On 3 Feb 2006 11:10:27 -0800, [email protected] wrote:
>I have an old 6" delta jointer that uses the pork chop style jointer
>guard. However, I don't have the jointer guard, so I would like to
>fabricate one but again I don't have one to start with. Does someone
>have some specifcs about this item that they could share? Like how it
>works? also if someone could share the dimensions of one that they
>have but best of all would be if someone could trace the outline and
>include dimensions. This way I could get one fabricated and have it be
>pretty close to accurate.
>
>Thanks,
>
>Fred
Why don't you just get a guard from Delta?
Kapowie?
"CW" <[email protected]> wrote in message
news:[email protected]...
> Bang.
> <[email protected]> wrote in message
> news:[email protected]...
>> Bump
>>
>
>
On 6 Feb 2006 10:35:08 -0800, [email protected] wrote:
>Thanks for your help Mike. I already have a picture, what I need is
>some dimensions ie. long, wide, thick and so forth. Is there any way
>you could help me out?
These are measurements for a guard from an old style
Delta/Miwaukee Accuset 6" joiner.
This may be a little hard to describe but here goes....
Overall length 11"
Width at the widest point 7 1/2"
Width at the narrow end is 1 3/4" with the added square part (for the
spring attach) adding another 3/4" to the width at that end.
The length of the fat part of the guard where it hits the fence is
4 1/2"
Overall thickness is 7/8"
Length of the shaft is approx 3" and hangs down beyond the hole in the
joiner by about 1/4"
If you need any other measurements let me know.
Mike O.