I have googled and found out it is a POS compared to the Performax. Okay,
but I can't afford a Performax.
If I spend the time to set it up, does it actually work; or is it that
bad...?
Is sand paper still available for it, or can something else substitute?
I probably only need it once in a while, but when I need it...
Herb Robinson wrote:
> Just a tad of pressure on the end that is going under the roller. I
> stated in my earlier post, the Ryobi has a rubber feed mat which
> appears to provide a better grip. If I don't provide that extra bit
> of "push", the work will not continue to feed and the sanding drum
> causes a "dip" in the piece being sanded.
It shouldn't do that - and won't - if set up properly. Some things to
check
1. Depth of cut too deep... how much can be taken off in one bite
depends on several things - grit, wood density, wood width, feed speed.
For me, normal is about 50% feed speed, 1/64 - 1/48 with #80 or finer;
up to 1/32 with #40 and a hard wood like oak or hickory, up to 1/16
with a softer wood like butternut or walnut.
2. Pressure roller height and/or tension is incorrect.
3. Feed belt is worn
4. Longish piece that is hanging down a bit so front edge is up.
Extending the table is a *real* help.
#1 & #2 are the most likely.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
Toller wrote:
> Is sand paper still available for it, or can something else
> substitute?
You don't use sand *paper*, you use sand cloth. All you need is long
rolls, cut your own.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
Herb Robinson wrote:
> With the Performax I have to
> apply a bit of pressure when feeding the work through
Pressure where and on what?
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
I had the Ryobi and just had a heap of trouble changing the paper. About
six months ago I bought a used Performax and sold the Ryobi. I must say the
problem of changing the paper has been resolved, but for operation, actually
prefer the Ryobi. With the Performax I have to apply a bit of pressure when
feeding the work through -- didn't have to do this with the Ryobi. Also,
the Ryobi had a rubber mat where the Performax uses a sandpaper type --
believe the rubber is much better -- provides a better grip. It uses the
same roll the Performax does, but as stated in another post, you are MUCH
better off getting a large roll and cutting your own strips.
"Toller" <[email protected]> wrote in message
news:[email protected]...
>I have googled and found out it is a POS compared to the Performax. Okay,
> but I can't afford a Performax.
>
> If I spend the time to set it up, does it actually work; or is it that
> bad...?
> Is sand paper still available for it, or can something else substitute?
>
> I probably only need it once in a while, but when I need it...
>
>
Just a tad of pressure on the end that is going under the roller. I stated
in my earlier post, the Ryobi has a rubber feed mat which appears to provide
a better grip. If I don't provide that extra bit of "push", the work will
not continue to feed and the sanding drum causes a "dip" in the piece being
sanded.
"dadiOH" <[email protected]> wrote in message
news:VO0Se.72$Di4.41@trnddc07...
> Herb Robinson wrote:
>
>> With the Performax I have to
>> apply a bit of pressure when feeding the work through
>
> Pressure where and on what?
>
> --
> dadiOH
> ____________________________
>
> dadiOH's dandies v3.06...
> ...a help file of info about MP3s, recording from
> LP/cassette and tips & tricks on this and that.
> Get it at http://mysite.verizon.net/xico
>
>