I am currently designing add-on fence 'wings' with measuring device
(left and right) for my CMS. I have room up to 56" per side. Should I
just make them 48" long as I am using T-slot extrusion for the stop
mechanism which is maximum 48"? Obviously I can add a second piece to
make up the remaining length if I make them longer.
Your input would be appreciated.
On Dec 3, 6:29 pm, "maico" <[email protected]> wrote:
> I am currently designing add-on fence 'wings' with measuring device
> (left and right) for my CMS. I have room up to 56" per side. Should I
> just make them 48" long as I am using T-slot extrusion for the stop
> mechanism which is maximum 48"? Obviously I can add a second piece to
> make up the remaining length if I make them longer.
>
> Your input would be appreciated.
Is your saw moveable? If so, I'd go with 48", but allow myself the
option to attach another full 48" section for when I need to make
longer cuts.
JP
Perhaps I should have mentioned that it is for a stationary mitre
bench.
Jay Pique wrote:
> On Dec 3, 6:29 pm, "maico" <[email protected]> wrote:
> > I am currently designing add-on fence 'wings' with measuring device
> > (left and right) for my CMS. I have room up to 56" per side. Should I
> > just make them 48" long as I am using T-slot extrusion for the stop
> > mechanism which is maximum 48"? Obviously I can add a second piece to
> > make up the remaining length if I make them longer.
> >
> > Your input would be appreciated.
>
> Is your saw moveable? If so, I'd go with 48", but allow myself the
> option to attach another full 48" section for when I need to make
> longer cuts.
>
> JP
I like your viewpoint of the 8' board: it would be a problem to split
it in half if it were a 48" fence. Mind you, there is at least another
foot between the blade and the start of the add on fence, therefore
giving me 60".
The only potential problem is possibly not having a hard stop for cuts
longer than 60". Having a physical fence there really doesn't matter
otherwise.
Thank you for your input. Is there anything else I should consider?
Morris Dovey wrote:
> maico (in [email protected]) said:
>
> | I am currently designing add-on fence 'wings' with measuring device
> | (left and right) for my CMS. I have room up to 56" per side.
> | Should I just make them 48" long as I am using T-slot extrusion for
> | the stop mechanism which is maximum 48"? Obviously I can add a
> | second piece to make up the remaining length if I make them longer.
> |
> | Your input would be appreciated.
>
> The answer depends on your work. The minimum length depends on the
> length of stock you work with. Obviously, 56" per side isn't going to
> work if you're going to be cutting 10' boards - or even if you're
> going to be cutting within 40" of the end of an 8' board.
>
> I think the most helpful response is to suggest you give some thought
> to what you're doing and work it out for yourself.
>
> --
> Morris Dovey
> DeSoto Solar
> DeSoto, Iowa USA
> http://www.iedu.com/DeSoto
maico (in [email protected]) said:
| I am currently designing add-on fence 'wings' with measuring device
| (left and right) for my CMS. I have room up to 56" per side.
| Should I just make them 48" long as I am using T-slot extrusion for
| the stop mechanism which is maximum 48"? Obviously I can add a
| second piece to make up the remaining length if I make them longer.
|
| Your input would be appreciated.
The answer depends on your work. The minimum length depends on the
length of stock you work with. Obviously, 56" per side isn't going to
work if you're going to be cutting 10' boards - or even if you're
going to be cutting within 40" of the end of an 8' board.
I think the most helpful response is to suggest you give some thought
to what you're doing and work it out for yourself.
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto